Toughness and R-curve behaviour of laminated Si3N4/SiCw ceramics

Laminated Si₃N₄/SiC_w ceramics were successfully prepared by tape casting and hot-pressing. Its mechanical properties were measured and the impact resistance was discussed. The toughness of the laminated Si₃N₄/SiC_w ceramics was 13.5 MPa m^1/2, which was almost 1.6 times that of Si₃N₄/SiC_w composite ceramics, namely 8.5 MPa m^1/2. Moreover, the indentation strength of laminated Si₃N₄/SiC_w ceramics was not sensitive to increasing indentation loads and exhibited a rising R-curve behaviour, indicating that the laminated Si₃N₄/SiC_w ceramics had excellent impact resistance. The improved toughness and impact resistance of laminated Si₃N₄/SiC_w ceramics was attributed to the residual stress caused by a thermal expansion coefficient mismatch between the different layers, resulting in crack deflection and bridging of SiC whiskers in the interface layer, thus consuming a large amount of fracture work.     

Development and characterisation of microporous biomimetic scaffolds loaded with magnetic nanoparticles as bone repairing material

Fine-tuning of the scaffolds structural features for bone tissue engineering can be an efficient approach to regulate the specific response of the osteoblasts. Here, we loaded magnetic nanoparticles aka superparamagnetic iron oxide nanoparticles (SPIONs) into 3D composite scaffolds based on biological macromolecules (chitosan, collagen, hyaluronic acid) and calcium phosphates for potential applications in bone regeneration, using a biomimetic approach. We assessed the effects of organic (chitosan/collagen/hyaluronic acid) and inorganic (calcium phosphates, SPIONs) phase over the final features of the magnetic scaffolds (MS). Mechanical properties, magnetic susceptibility and biological fluids retention are strongly dependent on the final composition of MS and within the recommended range for application in bone regeneration. The MS architecture/pore size can be made bespoken through changes of the final organic/inorganic ratio. The scaffolds undertake mild degradation as the presence of inorganic components hinders the enzyme catalytic activity. In vitro studies indicated that osteoblasts (SaOS-2) on MS9 had similar cell behaviour activity in comparison with the TCP control. In vivo data showed an evident development of integration and resorption of the MS composites with low inflammation activity. Current findings suggest that the combination of SPIONs into 3D composite scaffolds can be a promising toolkit for bone regeneration.     

Improvement of a commercial calcium phosphate bone cement by means of drug delivery and increased injectability

Calcium phosphate cements (CPCs) have been increasingly used as synthetic bone substitutes for repair and regeneration of bone defects given their biocompatibility, resemblance to bone and malleability. Moreover, their use as local antibiotic delivery systems is of main interest against bone infections, avoiding the adverse effects of high dosages of conventional therapy. The main goals of this work were to improve the properties of a commercial CPC (Neocement®), turning it injectable, and to provide it with a new functionality as a drug delivery system able to ensure a sustained release of an antibiotic commonly used in orthopaedics (gentamicin sulphate, GS). For this, the influence of the liquid phase amount (%LP) and type of polymer contained in the formulation (chitosan, Chi, or hydroxypropyl methylcellulose, HPMC) on the basic properties of the material was evaluated. It was found that the formulation containing 42%LP + HPMC+1.87% wt GS was the best one. It showed suitable setting and mechanical properties, and injectability around 87% (much superior to the original Neocement®, with 31%). It ensured a sustained release of GS for at least 14 days, at antibacterial levels. The antibiotic released is highly effective against S. epidermidis, but also presents some antibacterial activity against S. aureus. The CPC revealed to be non-cytotoxic. Moreover, it demonstrated good flowability and connectivity with human cadaveric trabecular bone.     

Calcium aluminate cement in castable alumina: From hydrate bonding to the in situ formation of calcium hexaluminate

Calcium hexaluminate (CA₆) is an intrinsically densification-resistant material, therefore, its porous structures are key materials for applications as high-temperature thermal insulators. This article reports on the combination of calcined alumina and calcium aluminate cement (CAC) in castable aqueous suspensions for the in situ production of porous CA₆. The CAC content (10–34 vol%) and the curing conditions ensure structural integrity prior to sintering and maximize the development of hydrated phases. Changes in physical properties, crystalline phases, and microstructure were investigated after isothermal treatments (120–1500 °C), and three sequential porogenic events were observed. The hydration of CAC preserved the water-derived pores (up to 120 °C), and the dehydroxylation of CAC hydrates (250–700 °C) generated inter-particles pores. Moreover, the in situ expansive formation of CA₂ and CA₆ (900–1500 °C) hindered densification and generated intra-particle pores. Such events differed from those observed with other CaO sources, and resulted in significantly higher pores content and lower thermal conductivity.     

Modulation of electrical transport in calcium cobaltite ceramics and thick films through microstructure control and doping

Ca₃Co₄O₉ is a promising p-type thermoelectric oxide material having intrinsically low thermal conductivity. With low cost and opportunities for automatic large scale production, thick film technologies offer considerable potential for a new generation of micro-sized thermoelectric coolers or generators. Here, based on the chemical composition optimized by traditional solid state reaction for bulk samples, we present a viable approach to modulating the electrical transport properties of screen-printed calcium cobaltite thick films through control of the microstructural evolution by optimized heat-treatment. XRD and TEM analysis confirmed the formation of high-quality calcium cobaltite grains. By creating 2.0 at% cobalt deficiency in Ca_2.7Bi_0.3Co₄O_9+δ, the pressureless sintered ceramics reached the highest power factor of 98.0 μWm^?1 K^-2 at 823 K, through enhancement of electrical conductivity by reduction of poorly conducting secondary phases. Subsequently, textured thick films of Ca_2.7Bi_0.3Co_3.92O_9+δ were efficiently tailored by controlling the sintering temperature and holding time. Optimized Ca_2.7Bi_0.3Co_3.92O_9+δ thick films sintered at 1203 K for 8 h exhibited the maximum power factor of 55.5 μWm^?1 K^-2 at 673 K through microstructure control.     

Enhancement in the osteogenesis and angiogenesis of calcium phosphate cement by incorporating magnesium-containing silicates

Based on the good osteogenic and angiogenic effects of silicon and magnesium elements, three types of micro-nano magnesium-containing silicates (MS), including akermanite (Ake, Ca₂MgSi₂O₇), diopside (Dio, CaMgSi₂O₆) and forsterite (For, Mg₂SiO₄), were incorporated into calcium phosphate cement (CPC) to improve its osteogenic and angiogenic performances for clinical application. In this present work, the physicochemical properties, osteogenesis and angiogenesis of MS/CPCs (Ake/CPCs, Dio/CPCs and For/CPCs) were investigated systematically and comparatively. The results showed that all MS/CPCs had good biomineralization and significantly stimulated the osteogenic differentiation of mBMSCs and angiogenic differentiation of HUVECs, respectively. Besides, the stimulating effects were related to not only the category of MS, but also the content of MS. The For/CPCs had a good angiogenic property but their initial setting times were beyond 60 min. The Dio/CPCs showed the lowest biological performance among the three groups of MS/CPCs due to the lower ion release (Si and Mg). The Ake was the ideal modifier that could provide CPC with appropriate physicochemical properties, better osteogenesis and angiogenesis. Simultaneously, a higher addition (10 wt%) of akermanite resulted in the best potential to bone regeneration. Taken together, this research provides an effective approach to improve the overall performance of CPC, and 10Ake/CPC is of great promising prospect in bone repair.     

碳氮分析仪测定造纸法再造烟叶中的碳酸钙含量

建立了碳氮分析仪法测定造纸法再造烟叶中碳酸钙含量的方法。通过热催化高温氧化反应对样品进行消解,检测经高温分解产生的CO_2气体,分别用不同的前处理方法,测定样品中的总碳和有机碳,用差量法计算出无机碳后,依据碳和碳酸钙分子量的换算,计算得出样品中碳酸钙的含量。结果显示:①待测液线性响应对应的最高碳含量为36mg;②样品本底碳量为14.5mg时,当加标碳量分别为2.5、5.0、7.0mg时平行检测3次的变异系数分别为7.60%、6.25%、3.77%;③方法的回收率范围为85.96%～111.16%;④方法的检出限和定量限分别为0.013mg和0.04mg。方法适合于测定造纸法再造烟叶中碳酸钙的含量。     

Simple and novel synthesis of zirconia whiskers from a phosphate flux

High quality zirconia whiskers have been successfully prepared by molten salt method, using zirconium oxychloride (ZrOCl₂·8H₂O) and sodium phosphate tribasic dodecahydrate (Na₃PO₄·12H₂O) as precursor and molten salt, respectively. The effects of types of molten salt and heat treatment temperature on the formation of zirconia whiskers were characterized by XRD, Raman, DTA-TG, FE-SEM, TEM, SAED and HR-TEM. When Na₃PO₄·12H₂O is utilized as molten salt and the heat treatment temperature is 900?°C, the as-prepared zirconia whiskers with length ranging from 4?µm to 8?µm show an average aspect ratio of 25. The obtained ZrO₂ whiskers with monoclinic structure are elongated along [010] direction and exhibit a smooth surface with no distinct defects. The XRD and Raman results reveal that the phase transformation from tetragonal zirconia to monoclinic zirconia occurs with the increased crystal size and the water quenching treatment can significantly reduce the content of sodium zirconium phosphate [Na_9–4×Zr_x(PO₄)₃] in the final product. The growth mechanism of zirconia whiskers is supposed to be a dissolution-precipitation process. Since the sodium zirconium phosphate [Na_9–4×Zr_x(PO₄)₃] effectively promotes the dissolution of zirconia in liquid molten salt, zirconia can grow into zirconia whiskers according to its anisotropy.     

High-temperature stability of Mg(Al,Cr)2O4 spinel co-existing with calcium aluminates in air

Cr₂O₃ is a well-known corrosion resistant oxide used in refractory applications. However, it can oxidize into toxic and water-soluble Cr(VI) compounds upon reaction with calcium aluminate cement phases in the presence of oxygen, which subsequently causes disposal problems after use. This study describes the extent to which chromium in the spinel Mg(Al,Cr)₂O₄ phase can be oxidized to Cr(VI) when it reacts with the calcium aluminate cement phases C₁₂A₇, CA, CA₂ and free CaO at 1300 °C in air, using XRD, XPS and leaching tests (TRGS 613 standard) as analytical tools. On reaction with CaO, the Mg(Al,Cr^III)₂O₄ spinel mainly transformed into hauyne (Ca₄Al₆Cr^VIO₁₆) and Ca₅Cr₃O₁₂ which contains both Cr(IV) and Cr(VI). The reaction of C₁₂A₇ and CA with the spinel phase also resulted in the formation of Ca₄Al₆CrO₁₆. Conversely, the reaction of Mg(Al,Cr^III)₂O₄ spinel with CA₂ resulted in the formation of only a trace amount of Cr(VI). Water-soluble Cr(VI) leached in large quantities (>100 mg/L) from samples where the Mg(Al,Cr^III)₂O₄ reacted with either C₁₂A₇ or CA. Almost no Cr(VI) leached from the sample when Mg(Al,Cr^III)₂O₄ reacted with CaO, using the standard TRGS 613 leach test, but a significant amount of Cr(VI) was released into solution when leached with a HCl solution for 12 h. Both Cr(IV) and Cr(VI) present in the Ca₅Cr₃O₁₂ dissolved into acidic solution. Only a small amount of Cr(VI) leached from the sample that resulted when spinel was reacted with CA₂, even after a prolonged HCl leach. Cr(III) in spinel Mg(Al,Cr)₂O₄ is very stable and does not leach in either distilled water or acidic solution.