Colossal dielectric response and relaxation behavior in novel system of Zr4+ and Nb5+ co-substituted CaCu3Ti4O12 ceramics

In this work, we developed a novel system of isovalent Zr⁴⁺ and donor Nb⁵⁺ co-doped CaCu₃Ti₄O₁₂ (CCTO) ceramics to enhance dielectric response. The influences of Zr⁴⁺ and Nb⁵⁺ co-substituting on the colossal dielectric response and relaxation behavior of the CCTO ceramics fabricated by a conventional solid-phase synthesis method were investigated methodically. Co-doping of Zr⁴⁺ and Nb⁵⁺ ions leads to a significant reduction in grain size for the CCTO ceramics sintered at 1060 °C for 10 h. XRD and Raman results of the CaCu₃Ti_3.8-xZr_xNb_0.2O₁₂ (CCTZNO) ceramics show a cubic perovskite structure with space group Im-3. The first principle calculation result exhibits a better thermodynamic stability of the CCTO structure co-doped with Zr⁴⁺ and Nb⁵⁺ ions than that of single-doped with Zr⁴⁺ or Nb⁵⁺ ion. Interestingly, the CCTZNO ceramics exhibit greatly improved dielectric constant (~10⁵) at a frequency range of 10²–10⁵ Hz and at a temperature range of 20–210 °C, indicating a giant dielectric response within broader frequency and temperature ranges. The dielectric properties of CCTZNO ceramics were analyzed from the viewpoints of defect-dipole effect and internal barrier layer capacitance (IBLC) model. Accordingly, the immensely enhanced dielectric response is primarily ascribed to the complex defect dipoles associated with oxygen vacancies by co-doping Zr⁴⁺ and Nb⁵⁺ ions into CCTO structure. In addition, the obvious dielectric relaxation behavior has been found in CCTZNO ceramics, and the relaxation process in middle frequency regions is attributed to the grain boundary response confirmed by complex impedance spectroscopy and electric modulus.     

Complex study of protective Cr3C2–NiAl coatings deposited by vacuum electro-spark alloying,pulsed cathodic arc evaporation,magnetron sputtering,and hybrid technology

Coatings were obtained by vacuum electro-spark alloying (VESA), pulsed cathodic arc evaporation (PCAE), magnetron sputtering (MS) techniques and VESA-PCAE-MS hybrid technology using Cr₃C₂–NiAl electrodes. The structure of the coatings was analyzed using scanning and transmission electron microscopy, X-ray diffraction and energy-dispersive spectroscopy. Mechanical properties were determined by nanoindentation, while tribological properties were assessed using pin-on-disk tribometer. Corrosion resistance was estimated by voltammetry in 1 N H₂SO₄ and 3.5%NaCl solutions. Oxidation resistance tests were performed at 800°С in air. The VESA coating had the highest thickness, low friction coefficient and high wear resistance. PCAE coating demonstrated the highest hardness (24 GPa) and elastic recovery (59%), oxidation resistance and superior corrosion resistance both in 1 N H₂SO₄ (i_corr = 70 μА/cm²) and 3.5%NaCl (i_corr = 0.74 μА/cm²) solutions. The MS coating had average mechanical properties and low corrosion current density (71 μА/cm²) in 1 N H₂SO₄. Deposition of coatings using VESA-PCAE-MS hybrid technology led to an increase in corrosion and oxidation resistance at least by 1.5 times in comparison with the VESA coating.     

Spark plasma sintering of UO2 nanopowders: Pressure,heating rate and current effects

We analysed with different methods the densification of UO₂ nanopowders in SPS under constant heating rate (CHR) and isothermal sintering conditions. The apparent activation energy of densification in SPS (75 kJ/mol with CHR method) is significantly smaller than in conventional sintering. It is shown that this is likely not an effect of the applied current. We also observed a threshold stress at 64 MPa for the transition from pressure-insensitive sintering (stress exponent n≈0) to pressure-assisted sintering, suggesting that the contribution of the capillary stresses in such nanopowders is comparable with the typical stress applied in SPS.     

Facile synthesis of black phosphorus directly grown on carbon paper as an efficient OER Electrocatalyst: Role of Interfacial charge transfer and induced local charge distribution

Black phosphorus (BP), as a new 2D material, is normally synthesized by a high-pressure and high-temperature (HPHT) method from white and red phosphorus, which severely hinders the further development of BP for any potential applications and leads to search for other potential applications of BP with big challenge. Herein, we develop a facile and efficient Thermal-Vaporization-Transformation (TVT) approach to prepare a highly active BP directly grown on carbon paper as the electrode for Oxygen evolution reaction (OER), showing a low onset potential of 1.45 V versus RHE. Simultaneously, the current density of BP-CP illustrates the excellent electro-catalysis stability only decreases by 3.4% after continuous operation for 10000 s. Meanwhile, the density functional theory (DFT) calculations further illustrates the P-doped carbon layer in the upper side of BP layer is actually responsible for its enhanced OER property, and the adjacent carbon atoms of the embedded P atoms are actually the active sites due to the induced local change distribution by intramolecular change transfer. Considering the facile, but efficient and scalable, TVT approach can directly synthesize BP-CP with excellent OER performance, which is promising for BP electrocatalysts used for OER in metal-air batteries, fuel cells, water-splitting devices, even other key renewable energy.     

Optimization of hydrogen enrichment via palladium membrane in vacuum environments using Taguchi method and normalized regression analysis

In this study, the separation of hydrogen from gas mixtures using a palladium membrane coupled with a vacuum environment on the permeate side was studied experimentally. The gas mixtures composed of H₂, N₂, and CO₂ were used as the feed. Hydrogen permeation fluxes were measured with membrane operating temperature in the range of 320–380 °C, pressures on the retentate side in the range of 2–5 atm, and vacuum pressures on the permeate side in the range of 15–51 kPa. The Taguchi method was used to design the operating conditions for the experiments based on an orthogonal array. Using the measured H₂ permeation fluxes from the Taguchi approach, the stepwise regression analysis was also employed for establishing the prediction models of H₂ permeation flux, followed by the analysis of variance (ANOVA) to identify the significance and suitability of operating conditions. Based on both the Taguchi approach and ANOVA, the H₂ permeation flux was mostly affected by the gas mixture composition, followed by the retentate side pressure, the vacuum degree, and the membrane temperature. The predicted optimal operating conditions were the gas mixture with 75% H₂ and 25% N₂, the membrane temperature of 320 °C, the retentate side pressure of 5 atm, and the vacuum degree of 51 kPa. Under these conditions, the H₂ permeation flux was 0.185 mol s^?1 m^?2. A second-order normalized regression model with a relative error of less than 7% was obtained based on the measured H₂ permeation flux.     

Electric field-assisted synthesis/sintering cerium oxide: 5 wt.% gadolinium oxide

Gadolinium oxide ceramic powders were mixed to cerium oxide ceramic powders, pressed to pellets, and sintered either at 1450 °C or applying 200 V cm⁻¹ electric field at 800 °C, 900 °C and 1000 °C. The structural phases and the microstructure of the sintered pellets were analyzed by X-ray diffraction and scanning electron microscopy, respectively. The formation of substitutional solid solution was followed by monitoring the increase of the electrical conductivity by impedance spectroscopy and X-ray diffraction. The main results show that Joule heating due to the flow through the pellets of the electric current, which was produced by the application of the electric field, allows for promoting partial solid solution as well as partial sintering the ceria-gadolinia pellets. Moreover, grain growth that occurred in the high temperature sintered pellets was inhibited in the electric field-assisted synthesized/sintered pellets, being an alternative technique for producing cerium oxide-gadolinium oxide solid solutions.     

小型无线场强探测传感器研究

近年来,微波加热因其高效性和清洁无污染等优点广泛应用于各个领域。然而,微波加热的不均匀性限制了微波作为高效加热能源的应用。通过测量和分析加热腔中的电场分布情况可以帮助设计人员改进微波加热腔体设计,提高微波加热的均匀性。现有的场强测量设备均为有线设备,应用场景极为有限。因此,本文提出了一种由探头、接收机和上位机三部分组成的无线场强探测传感器。介绍了无线场强探测传感器的结构和原理,采用横电磁波小室进行校准。通过一系列测量实验表明实测值与标准场强仪测量值一致性较好,可满足工程测量需求。     

Steering feel improvement by mathematical modeling of the Electric Power Steering system

Currently, the Electric Power Steering (EPS) system is an essential component of the vehicle because it provides assistive steering torque to the driver. To ensure a faster steering response, the position of the EPS in some vehicles is moved closer to the tire rather than the steering wheel. The steering torque, which is provided by the EPS in the steering system, mainly affects the driver’s feel while steering. Therefore, the driver often feels uncomfortable owing to such positioning of the EPS in the steering system. In particular, the nonlinearity of the Universal Joint (UJ), which is one of parts of the steering system, can be felt at the steering wheel side.In this paper, we proposed an algorithm based on the mathematical model of the steering torque in the steering system to improve the steering feel. The mathematical model is structured using parameters that can be obtained from the information of the steering system. Moreover, the formulation of the steering torque consists of the two parts, namely the deformation part, which describes the propagation inside the steering system, and the friction part that describes the inherent friction in the UJ.Simulation and experiments were conducted to verify the proposed mathematical model with similar conditions to the real tire load during the steering motion. Furthermore, to improve the driver’s feel during steering, a torque compensation algorithm is proposed and verified through experiments.     

Microcrack healing in zirconia ceramics under a DC electric field/current

Flash event caused by a DC electric field/current was applied to the crack healing in 8 mol % Y₂O₃ stabilized cubic ZrO₂ polycrystals (8Y-CSZ). The flash event, which occurred by applying the DC power higher than a critical value of 100 mW/mm³, successfully healed the microcrack within several minutes without any healing agents at a furnace temperature of 800 °C. As compared to the healing treatment under static annealing, the healing phenomena were accelerated about 2 times under the flash treatment even at the same temperatures, suggesting that the enhanced healing phenomena cannot be explained only by the temperature effect. Since the rate of grain growth was accelerated under the flash treatment, the flash healing would be accelerated through the current-enhanced diffusional processes. This study shows for the first time that the flash event has a potential to apply to the crack healing process in the ceramic materials and composites.     

Fabrication and optical properties of transparent LaErZr2O7 ceramic with high excess contents of La and Er

In this study, transparent LaErZr₂O₇ ceramic with high excess La and Er contents (nominally La_1.28Er_1.28Zr₂O_7.84) was successfully prepared by vacuum sintering at 1850?°C for 6?h using nanosized powder. The XRD, SEM, EDX and TEM results reveal that the single pyrochlore phase in the powder sample transforms to the coexistence of La-rich pyrochlore phase and Er-rich defect fluorite phase after high temperature sintering. The high excess amounts of La and Er favor the formation of pyrochlore structure. Despite the coexistence of two phases, the sample with 1?mm thickness shows excellent in-line transmittance in the visible to mid-infrared region (as high as 81% at 1100?nm). The upconversion and infrared emission under 980?nm exciting were measured and discussed as well.