水提法提取—电感耦合等离子体质谱法测定婴幼儿配方奶粉中的碘

用水提取婴幼儿奶粉中的碘,亚铁氰化钾和乙酸锌盐析法沉淀蛋白,过滤后可以得到澄清处理液。用电感耦合等离子体质谱对提取样液进行测定,130Te作为内标物进行定量分析。该方法简便快捷,检出限为0.10 mg/kg加标回收率为90.8%~109%,相关系数0.999,精密度试验RSD2%。     

Influence of Bridgman solidification on microstructures and magnetic behaviors of a non-equiatomic FeCoNiAlSi high-entropy alloy

The non-equiatomic FeCoNiAlSi alloy is prepared by the Bridgman solidification (BS) technique at different withdrawal velocities (V = 30, 100, and 200 μm/s). Various characterization techniques have been used to study the microstructure and crystal orientation. The morphological evolutions accompanying the crystal growth of the alloy prepared at different withdrawal velocities are nearly the same, from equiaxed grains to columnar crystals. The transition of coercivity is closely related to the local microstructure, while the saturation magnetization changes little at different sites. The coercivity can be significantly reduced from the equiaxed grain area to the columnar crystal area when the applied magnetic field direction is parallel to the crystal growth direction, no matter what is the withdrawal velocity. In addition, the alloy possesses magnetic anisotropy when the applied magnetic field is in different directions.     

Electrochemical growth and characterization of iron doped cadmium sulfide thin films

Cadmium Sulfide and Ferrous doped Cadmium Sulfide thin films have been prepared on different substrates using an electrodeposition technique. Linear sweep voltammetric analysis has been carried out to determine deposition potential of the prepared films. X-ray diffraction analysis showed that the prepared films possess polycrystalline nature with hexagonal structure. Surface morphology and film composition have been analyzed using Scanning electron microscopy and Energy dispersive analysis by X-rays. Optical absorption analysis showed that the prepared films are found to exhibit Band gap value in the range between 2.3, 2.8 eV for Cadmium Sulfide and Ferrous doped Cadmium Sulfide.     

Low cycle fatigue behavior of a eutectic 80Au/20Sn solder alloy

The eutectic 80Au/20Sn solder alloy is widely used in high power electronics and optoelectronics packaging. In this study, low cycle fatigue behavior of a eutectic 80Au/20Sn solder alloy is reported. The 80Au/20Sn solder shows a quasi-static fracture characteristic at high strain rates, and then gradually transforms from a transgranular fracture (dominated by fatigue damage) to intergranular fracture (dominated by creep damage) at low strain rates with increasing temperature. Coffin-Manson and Morrow models are proposed to evaluate the low cycle fatigue behavior of the 80Au/20Sn solder. Besides, the 80Au/20Sn solder has enhanced fatigue resistance compared to the 63Sn/37Pb solder.     

Effect of microstructure on the fatigue crack growth behaviour of a near-α Ti alloy

Fatigue crack growth behaviour of Ti–6Al–2Zr–1.5Mo–1.5V (VT-20 a near-α Ti alloy) was studied in lamellar, bimodal and acicular microstructural conditions. Fatigue crack growth tests at both increasing and decreasing stress intensity factor range values were performed at ambient temperature and a loading ratio of 0.3 using compact tension samples. Lamellar and acicular microstructures showed lower fatigue crack growth rates as compared to the bimodal microstructure due to the tortuous nature of cracks in the former and the cleavage of primary α in the latter. The threshold stress intensity factor range was highest for acicular microstructure.     

噻吩在镍基非晶态合金上的吸附和脱附

应用静态吸附、动态吸附、程序升温脱附和程序升温还原等实验方法，考察了噻吩在Ni基非晶态合金上的吸附和脱附行为。常温下，噻吩分子首先吸附在清洁的Ni表面，并立刻被活化，发生氢解反应，C-S键断裂，释放出烃类部分，S留在Ni原子上。噻吩可以在Ni基非晶态合金表面发生强度不同的化学吸附。弱化学吸附的噻吩可以脱附；强化学吸附的噻吩不会脱附，而在高温下发生氢解反应。     

循环伏安法在润滑油检测中的应用

介绍了循环伏安法的产生背景、原理。应用该技术可以快速、方便地对润滑油中抗氧剂、总酸（碱）值进行测定，并且可以对不同厂家润滑油的抗氧剂包进行区别。该技术还可以有效地评价润滑油的使用寿命和设备工作状况。     

不锈钢管道坡口加工的新方法

对于不锈钢管及合金钢管坡口的加工,采用以往的加工方法切割出来的坡口一般参差不平、比较粗糙,难于打磨平整。使用LGK空气等离子切割机和磁力管道切割机的组合加上一定的辅助手段,改善了不锈钢管及合金钢管的坡口加工效果,使加工出来的坡口像碳钢管一样平整,更加容易打磨组焊。文章介绍了这一新方法所用的设备、材料、切割原理以及操作过程。     

Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.     

原油基压裂液研究

研制了一种适用于低压、低渗、水敏性储集层的新型原油基压裂液体系。根据基液原油的组分合成相应的增稠剂，增稠剂在原油中与交联剂反应，形成网状结构，使原油成为黏度可以调控的冻胶，从根本上改变了油基压裂液以柴油、煤油为基液的现状，降低了油基压裂液的成本，同时还提高了压裂液的抗温、抗剪切和破胶性能，并将交联时间缩短到2h以内，可以满足现场压裂施工的要求，大大降低了施工强度和压裂改造的综合成本。在青海油田进行的现场先导试验取得成功。图9表1参5