一种磁控管用扼流线圈仿真设计

采用电路仿真软件仿真滤波组件S参数曲线,观察曲线随器件参数的变化;介绍利用三维全波电磁仿真软件HFSS简化设计流程的方法,并与测试结果对比。结果表明:利用3D仿真软件在满足器件设计精度的同时可以简化线圈的设计流程。     

Decreasing Filter Cake Resistance by Using Packing Structures

Packed beds used in absorption columns are evaluated to determine whether they can also be beneficial for cake‐forming filtrations. To assess this, model systems are characterized and separated by using a dead‐end filter cell. Filtrations are conducted with different packings; the filtrate amount over time and resulting turbidity are evaluated. Packings increase the filter cake resistance and the separation time of the cakes formed with approximately incompressible solids. However, they exhibit a positive effect on the filtration of a more complex, compressible substance; the process is not only accelerated, but also the quality of the obtained filtrate is not compromised. These results demonstrate potential in the use of packed beds for the filtration of complex biogenic suspensions.     

Interface reactions between rutile coatings and molten aluminium or AlSi7Mg0.6 alloy

Rutile coatings deposited on corundum substrates are considered as promising functional elements improving the efficiency of the filtration of oxide inclusions out of aluminium melts. This contribution describes the reactions between rutile and two kinds of the aluminium melts and discusses the consequences of these reactions for the filtration process. It was found that the contact of rutile coatings with molten aluminium leads to the formation of a corundum layer at the solid/liquid interface. The exposure of the rutile coatings to molten AlSi7Mg0.6 alloy produces an interface layer of MgTiO₃. The interface layers possess defined orientation relationship to rutile which is characteristic for locally heteroepitaxial growth. The density functional theory calculations revealed that the TiO₂/α-Al₂O₃ and TiO₂/MgTiO₃ interfaces with the orientation relationships observed experimentally have low interface energies. The mechanisms of the interface layer formation and the impact of these layers on the degradation of the rutile coatings are discussed.     

Parameter Estimation for Incompressible Cake Filtration: Advantages of a Modified Fitting Method

There is a widely used linear strategy to determine the parameters specific cake resistance and filter medium resistance in incompressible cake filtration. In this article, it is intended to demonstrate that this strategy has some disadvantages and should be replaced by an alternative nonlinear approach which yields more exact results. Even though the gains in precision are small for most cases, the nonlinear strategy is favored because it involves no extra effort and is grounded in the same physical theory as the original approach. This claim is based on a broad simulation study using noisy data with known parameter values to compare both fitting strategies and judge their accuracies.     

一种高效过滤亚微米级细颗粒的新液固过滤技术——表层过滤

论述一种新的可高效过滤液体中亚微米级细颗粒的表层过滤技术,分析了表层过滤技术的特点、过滤模式、表层过滤基本条件和设计计算中所必需的数学模型。介绍了表层过滤技术在我国工业生产上推广应用的概况。     

废油循环再利用的研究

废油,是其中含有5%~10%为不能被利用的废物,而90%~95%是可以重新加工再利用的,使再生油资源成为解决我国目前能源困境的一个非常有效的途径,从石油中提炼基础油产品率很低,生产1 t至少需要5 t原油。从某种方面上讲利用再生废油要比开发原油经济的多,可以节省大量的时间和资金。近年来我国平均每年要进口2亿多吨原油,进口200多万吨润滑油,而且进口原油的产地大多又受战乱,政权更迭等政治因素影响。所以,对废油再生和利用,不仅具有重要的经济意义、环保意义,还具有重要的政治意义。     

MS Project 4.0 forWindows使用初探

本文介绍了微软公司项目管理软件Project4．0Forwindows的几点使用小经验。     

Ultra-fine particles release from hardcopy devices: sources, real-room measurements and efficiency of filter accessories

The release of ultra-fine particles (UFP, d < 0.1 µm) from hardcopy devices such as laser printers into the indoor environment is currently a topic of high concern. The general emission behavior of a printer can be examined by conducting emission test chamber measurements with particle-counting devices. Chamber experiments with modified laser printers operated without toner or paper also revealed UFP emissions. On the basis of these results we reasonably doubt the opinion that UFPs primarily originate from the toner. Instead, the high-temperature fuser unit is assumed to be one source for ultra-fine particle emission. UFP release typically follows the flow path of the cooling air which may leave the printer casing at various points (e.g. the paper tray). This limits the usability of the commercial filter systems available because the released particles could leave the printer without passing through the filter. Chamber measurements with various filter systems retrofitted to a laser printer demonstrate different efficiencies of UFP reduction. Complementary experiments were carried out in an office room. Here the decay of the particle concentration after a print job was about ten times slower than in the test chamber. A toxicological assessment of the emitted particles requires that their chemical composition be known. Due to the low mass of the released UFPs chemical analysis needs a prior enrichment on a feasible media. Experiments using electrostatic precipitation showed a flame retardant (tri-xylyl phosphate) whose concentration on the media was dependent on the number of pages printed. Whether this compound was particle-bound could not be determined.     

System level design and analysis of a fourth‐order continuous‐time delta‐sigma modulator using relaxed gain‐band‐width amplifiers

In this paper, based on mathematical approaches and behavioral modeling of internal blocks, an algorithm of designing a continuous‐time delta‐sigma modulator (CT ΔΣM) with aggressive noise shaping is discussed. Using proposed methods, the coefficients of modulator can be calculated directly while the finite gain‐band‐width of amplifiers and rise/fall time of digital‐to‐analog convertors (DACs) in feedback path are included in the transfer function of CT loop filter. To decrease the number of amplifiers, a unique resonator is proposed. Also, an extra feedback DAC is introduced to further reduction of gain‐band‐width requirement of last amplifier. To verify the effectiveness of proposed methods, a fourth‐order, single loop, CT ΔΣM that benefits proportional‐integrator element for compensation of excess‐loop‐delay is realized in system and behavioral circuit levels. It has a 4‐bit quantizer, over‐sampling‐ratio of 10, and out‐of‐band‐gain of 12 dB. The peaking in signal‐transfer‐function is alleviated using a feed‐forward capacitor along with proper choosing of rest coefficients. The designed modulator has 78‐dB signal‐to‐noise‐ratio; even the non‐ideal behaviors of amplifiers and DACs are involved in simulations. Independent to sampling frequency, the proposed methods can be applied to other topologies of CT ΔΣMs. Copyright © 2017 John Wiley & Sons, Ltd.