A review of thin film electrolytes fabricated by physical vapor deposition for solid oxide fuel cells

The ohmic resistance in solid oxide fuel cells (SOFCs) mainly comes from the electrolyte, which can be reduced by developing novel electrolyte materials with higher ionic conductivity and/or fabricating thin-film electrolytes. Among various kinds of thin-film fabrication technology, the physical vapor deposition (PVD) method can reduce the electrolyte thickness to a few micrometers and mitigate the issues associated with high-temperature sintering, which is necessary for wet ceramic methods. This review summarizes recent development progress in thin-film electrolytes fabricated by the PVD method, especially pulsed laser deposition (PLD) and magnetron sputtering. At first, the importance of the substrate surface morphology for the quality of the film is emphasized. After that, the fabrication of thin-film doped-zirconia and doped-ceria electrolytes is presented, then we provide a brief summary of the works on other types of electrolytes prepared by PVD. Finally, we have come to the summary and made perspectives.     

Investigation of La0.6Sr0.4Co1-xNixO3-δ (x=0, 0.2, 0.4, 0.6, 0.8) catalysts on solid oxide fuel cells anode for biogas dry reforming

The introduction of catalyst on anode of solid oxide fuel cell (SOFC) has been an effective way to alleviate the carbon deposition when utilizing biogas as the fuel. A series of La_0.6Sr_0.4Co_1-xNi_xO_3-δ (x = 0, 0.2, 0.4, 0.6, 0.8) oxides are synthesized by sol-gel method and used as catalysts precursors for biogas dry reforming. The phase structure of La_0.6Sr_0.4Co_1-xNi_xO_3-δ oxides before and after reduction are characterized by X-ray diffraction (XRD). The texture properties, carbon deposition, CH₄ and CO₂ conversion rate of La_0.6Sr_0.4Co_1-xNi_xO_3-δ catalysts are evaluated and compared. The peak power density of 739 mW cm^?2 is obtained by a commercial SOFC with La_0.6Sr_0.4Co_0.4Ni_0.6O_3-δ catalyst at 850 °C when using a mixture of CH₄: CO₂ = 2:1 as fuel. This shows a great improvement from the cell without catalyst for internal dry reforming, which is attributed to the formation of NiCo alloy active species after reduction in H₂ atmosphere. The results indicate the benefits of inhibiting the carbon deposition on Ni-based anode through introducing the La_0.6Sr_0.4Co_0.4Ni_0.6O_3-δ catalyst precursor. Additionally, the dry reforming technology will also help to convert part of the exhaust heat into chemical energy and improve the efficiency of SOFC system with biogas fuel.     

Morphological influence of graphitic carbon nanofibers by N–F dual-doping on Pt electrocatalytic activity and stability for oxygen reduction reaction in polymer electrolyte membrane fuel cells

Morphology of carbon nanofibers significantly effects Pt nanoparticles dispersion and specific interaction with the support, which is an important aspect in the fuel cell performance of the electrocatalysts. This study emphasizes, the defects creation and structural evolution comprised due to N–F co-doping on graphitic carbon nanofibers (GNFs) of different morphologies, viz. GNF-linearly aligned platelets (L), antlers (A), herringbone (H), and their specific interaction with Pt nanoparticle in enhancing the oxygen reduction reaction (ORR). GNFs–NF–Pt catalysts exhibit better ORR electrocatalytic activity, superior durability that is solely ascribed to the morphological evolution and the doped N–F heteroatoms, prompting the charge density variations in the resultant carbon fiber matrices. Amongst, H–NF–Pt catalyst performed outstanding ORR activity with exceptional electrochemical stability, which shows only 20 mV loss in the half-wave potential whilst 100 mV loss for Pt/C catalyst on 20,000 potential cycling. The PEMFC comprising H–NF–Pt as cathode catalyst with minimum loading of 0.10 mg cm^?2, delivers power density of 0.942 W cm^?2 at current density of 2.50 A cm^?2 without backpressures in H₂–O₂ feeds. The H–NF–Pt catalyst owing to its hierarchical architectures, performs well in PEMFC at the minimized catalyst loading with outstanding stability that can significantly decrease total price for the fuel cell.     

Induced slim ferroelectric hysteresis loops and enhanced energy-storage properties of Mn-doped (Pb0·93La0.07)(Zr0·82Ti0.18)O3 anti-ferroelectric thick films by aerosol deposition

In this study, the high ferroelectric hysteresis loss of (Pb_0·93La_0.07)(Zr_0·82Ti_0.18)O₃ (PLZT 7/82/18) antiferroelectric (AFE) ceramics was reduced by employing a combinatorial approach of Mn acceptor doping followed by thick film fabrication via an aerosol deposition (AD) process. The grains of the as-deposited PLZT 7/82/18 AFE AD thick films were grown by thermal annealing at 550 °C to enhance their electrical properties. Investigation of the electrical properties revealed that Mn-doping results in improved dielectric and ferroelectric properties, increased dielectric breakdown strength (DBS), and energy-storage properties. The Mn-doped PLZT AFE AD films possess a frequency-independent high dielectric constant (ε_r ≈ 660) with low dielectric loss (tan δ ≈ 0.0146), making them suitable candidates for storage capacitor applications. The bipolar and unipolar polarization vs. electric field (P-E) hysteresis loops of PLZT 7/82/18 AFE AD thick films were found to be slimmer than those of their bulk form (double hysteresis) with significantly reduced ferroelectric hysteresis loss, which is attributed to the AD-induced mixed grain structure. The Mn-doped PLZT 7/82/18 AFE AD thick films exhibited a low remnant polarization (P_r ≈ 9.22 μC/cm²) at a high applied electric field (~2750 kV/cm). The energy-storage density and energy efficiency of the Mn-doped PLZT AFE AD thick films were calculated from unipolar P-E hysteresis loops and found to be ~38.33 J/cm³ and ~74%, respectively.     

Phase constitution,microstructure and mechanical properties of a Ni-based superalloy specially designed for additive manufacturing

In this study, a kind of Ni-based superalloy specially designed for additive manufacturing (AM) was investigated. Thermo-Calc simulation and differential scanning calorimetry (DSC) analysis were used to determine phases and their transformation temperature. Experimental specimens were prepared by laser metal deposition (LMD) and traditional casting method. Microstructure, phase constitution and mechanical properties of the alloy were characterized by scanning electron microscopy (SEM), transmission scanning electron microscopy (TEM), X-ray diffraction (XRD) and tensile tests. The results show that this alloy contains two basic phases, γ/γ', in addition to these phases, at least two secondary phases may be present, such as MC carbides and Laves phases. Furthermore, the as-deposited alloy has finer dendrite, its mean primary dendrite arm space (PDAS) is about 30-45 μm, and the average size of γ' particles is 100-150 nm. However, the dendrite size of the as-cast alloy is much larger and its PDAS is 300-500 μm with secondary and even third dendrite arms. Correspondingly, the alloy displays different tensile behavior with different processing methods, and the as-deposited specimen shows better ultimate tensile stress (1,085.7±51.7 MPa), yield stress (697±19.5 MPa) and elongation (25.8%±2.2%) than that of the as-cast specimen. The differences in mechanical properties of the alloy are due to the different morphology and size of dendrites, γ', and Laves phase, and the segregation of elements, etc. Such important information would be helpful for alloy application as well as new alloy development.     

农药沉积利用率喷雾指示剂诱惑红的酶标仪测定方法

诱惑红是一种水溶性染料,近年来被用作农药沉积利用率测定的指示剂。诱惑红的检测方法为高效液相色谱法和分光光度法。高效液相色谱法需要专门的分析仪器,且价格昂贵,可见分光光度计法操作繁琐,试剂用量大,耗时长,均不适宜田间快速高效测定。笔者发展了诱惑红的酶标仪测定方法,简单高效,可批量检测多个样品,且准确度和精密度高,线性关系良好,514 nm检测波长下不受其他农药影响,并应用于玉米无人飞机喷雾场景下农药雾滴在玉米冠层的沉积利用率测定。     

Effect of Cu-Rich Phase Precipitation on the Microstructure and Mechanical Properties of CoCrNiCux Medium-Entropy Alloys Prepared via Laser Directed Energy Deposition

CoCrNiCux (x=0.16,0.33,0.75,and 1) without macro-segregation medium-entropy alloys (MEAs) was prepared using laser directed energy deposition (LDED).The microstructure and mechanical properties of CoCrNiCux alloys with increas-ing Cu content were investigated.The results indicate that a single matrix phase changes into a dual-phase structure and the tensile fracture behaviors convert from brittle to plastic pattern with increasing Cu content in CoCrNiCux alloys.In addi-tion,the tensile strength of CoCrNiCux alloys increased from 148 to 820 MPa,and the ductility increased from 1 to 11％with increasing Cu content.The nano-precipitated particles had a mean size of approximately 20 nm in the Cu-rich phase area,and a large number of neatly arranged misfit dislocations were observed at the interface between the two phases due to Cu-rich phase precipitation in the CoCrNiCu alloy.These misfit dislocations hinder the movement of dislocations during tensile deformation,as observed through transmission electron microscopy.This allows the CoCrNiCu alloy to reach the largest tensile strength and plasticity,and a new strengthening mechanism was achieved for the CoCrNiCu alloy.Moreover,twins were observed in the matrix phase after tensile fracture.Simultaneously,the dual-phase structure with different elastic moduli coordinated with each other during the deformation process,significantly improving the plasticity and strength of the CoCrNiCu alloy.     

上升气泡内气溶胶沉降机理研究

气溶胶池洗过滤是反应堆严重事故中去除放射性源项的重要手段。本文以严重事故条件下上升气泡中气溶胶的滞留过程为背景，设计搭建了可视化单气泡鼓泡实验装置。通过该装置研究了气溶胶在上升气泡中的沉降效率，并与MELCOR中的气溶胶沉降模型计算结果进行了对比。结果表明，气溶胶沉降效率对气泡尺寸的变化较为敏感，当气体流量大于0.1 L/min时，气泡等效直径迅速增加，相应的气溶胶沉降效率快速降低；与MELCOR模型计算结果的对比表明，两者在总体趋势上呈现出较好的一致性，但计算结果低估了液相对气溶胶的实际去除能力，导致这种偏差的主要原因是气泡在上升过程中存在无规则的晃动以及气液界面的波动。     

Effect of laser power density on the electrochromic properties of WO3 films obtained by pulsed laser deposition

Pulsed laser deposition (PLD) was used to prepare tungsten trioxide (WO₃) films on ITO substrates with a varying laser power density of 4.0–5.5 W/cm². XPS indicated that when the laser power density decreased, the peak positions of the W 4f and O 1s orbits shifted slightly to low energy due to the difference in oxygen vacancies. As the laser power density decreased, W⁶⁺ gradually replaced the lattice position of O^2?, increasing oxygen vacancies in the lattice. The transmittance modulated values (ΔT) were over 44% at 830 nm, indicating strong absorption by the WO₃ thin films in the near-infrared ray. The switching time of the WO₃ thin films between bleached states and coloured states decreased as the laser power density increased due to the amorphous structure, morphology, and lower oxygen deficiency at a high power density. The high ΔT and very fast switching time of t_b (1.09 s) and t_c (6.01 s) demonstrated the excellent electrochromic (EC) properties of the WO₃ films prepared by PLD.     

Dielectric and ferroelectric properties of multilayer BaTiO3/NiFe2O4 thin films prepared by solution deposition technique

In this work different lead-free multilayered structures, composed of perovskite BaTiO₃ and spinel NiFe₂O₄ thin layers, were obtained by solution deposition method. Structural characterization of the sintered thin films confirmed the well-defined layered structure with overall thickness from 160 to 600 nm, crystalline nature of perovskite BaTiO₃ and spinel NiFe₂O₄ phases without secondary phases (after sintering below 900 °C) and grains on nanometer scale. Dielectric properties of the multiferroic multilayer BaTiO₃/NiFe₂O₄ thin films were analyzed in temperature and frequency range from 30 °C to 200 °C and 100 Hz to 1 MHz, respectively. In comparison to the pure BaTiO₃ films, the introduction of ferrite layer reduces dielectric response and increases low frequency permittivity dispersion of the multilayer thin films. The multilayer samples have shown relatively low dielectric loss with stronger contribution of conductivity at higher temperatures, and characteristic broad peak representing “relaxation” of the interface charge accumulation.