Tribological behavior studies of chemically bonded phosphate ceramic coatings reinforced with modified multi-walled carbon nanotubes (MWCNTs)

To improve the wear resistance of the chemically bonded phosphate ceramic coatings, MWCNTs are selected as the reinforcement after the modification. The high temperature wear experiment is carried out to investigate the wear behavior of the coatings with different temperatures. The results suggest that, when the temperature is below 500℃, MWCNTs can decrease friction coefficient, and the lowest friction coefficient is about 0.28, but MWCNTs lose the lubricant function at 500℃ and the friction coefficient keeps at the level of ~ 0.68. In addition, the wear resistance of coatings is improved with the introduction of MWCNTs at 100℃ and 300℃ (the wear rate is below 15X10^-3mm³/Nm), but keeps similar level at 500℃ (the wear rate is ~ 22 × 10⁻³mm³/Nm). Besides, the wear mechanism of the coatings reinforced by MWCNTs is also investigated based on the wear behavior and microstructural characterizations. MWCNTs improve the fracture toughness by preventing the crack generation and forming the bridge when crack occurs, which leads to smooth wear tracks and good wear resistance of coatings. The coatings with MWCNTs achieve poor wear resistance at 500℃ because MWCNTs lose their strength and resistance to fatigue by oxidizing.     

Highly efficient photocatalytic treatment of mixed dyes wastewater via visible-light-driven AgI–Ag3PO4/MWCNTs

A high-performance photocatalyst of AgI–Ag₃PO₄/multi-walled carbon nanotubes (MWCNTs) was fabricated by chemical precipitation method using KI, K₂HPO₄ and AgNO₃ in the presence of MWCNTs. Its structure and physical properties were characterized by means of scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), transmission electron microscope (TEM), X-ray diffraction (XRD), UV–vis absorption spectra, X-ray photo-electron spectroscopy (XPS), photoluminescence spectra (PL) and photocurrent techniques. SEM, TEM and EDS analyses verified that AgI–Ag₃PO₄ is successfully loaded on MWCNTs. AgI–Ag₃PO₄/MWCNTs possess the absorption edge of red shift and small band gap energy, and could absorb more photons in the visible region. PL and photocurrent analyses illustrated that AgI–Ag₃PO₄/MWCNTs have the lowest emission peak intensity and the highest photoelectric current, compared with Ag₃PO₄, AgI and AgI–Ag₃PO₄. By using the photocatalytic degradation of mixed dyes wastewater of Orange II and ponceau 4R as a model reaction, the photocatalytic efficiencies of Ag₃PO₄, AgI, AgI–Ag₃PO₄ and AgI–Ag₃PO₄/MWCNTs were evaluated. The reaction results showed that AgI–Ag₃PO₄/MWCNTs have strong photocatalytic activity and excellent chemical stability in repeated and long-term applications. Therefore, the prepared AgI–Ag₃PO₄/MWCNTs could act as a high-performance catalyst for the photocatalytic degradation of mixed dyes wastewater and also suggested the promising applications.     

Improved hydrogen adsorption of ZnO doped multi-walled carbon nanotubes

Hydrogen storage is still one of the most important problems to improve hydrogen energy usage widespread. New materials capable of storing hydrogen with high efficiency must be introduced to overcome this problem. In recent years, addition of metals or inorganic compounds to multiwalled carbon nanotubes (MWCNTs) has been generally used for hydrogen uptake studies to enhance adsorption property of the nanotubes. In this study, Zinc oxide (ZnO) nanoparticles doped MWCNTs (ZnO-MWCNTs) have been produced as new reversible hydrogen storage materials, and we have investigated characterization of ZnO-MWCNTs by XRD, SEM, TGA, TEM and BET analyses. The functionalized MWCNTs and ZnO doped MWCNTs were subjected to hydrogenation step by dynamic gas sorption analyser under pressure of 5–50 bar. The hydrogen uptake capacities of the materials under different pressures were measured gravimetrically. It was indicated that by controlling the pressures for hydrogenation of ZnO-MWCNTs induces the spillover of ZnO nanoparticles in the layer of MWCNTs which in return with high hydrogen adsorption capacity. Consequently, the hydrogen adsorption of the functionalized MWCNTs (f-MWCNTs) and the ZnO-MWCNTs were achieved to be 1.05 wt% and 2.7091 wt% under pressure of 50 bar as maximum.     

碘化多壁碳纳米管制备含有Ag/MWCNTs复合材料的银-环氧树脂浆料

提出一种将多壁碳纳米管碘化后制备银/多壁碳纳米管（Ag/MWCNTs）复合材料的方法。通过球磨对碘化多壁碳纳米管进行了功能化，并通过透射电子显微镜（TEM）、X射线衍射（XRD）、傅里叶变换红外光谱（FT-IR）、拉曼光谱和热重分析（TG）对其进行了表征。结果表明，经碘化处理后，银纳米粒子（Ag-NPs）能更好地粘附在碳纳米管表面，改善了银纳米粒子与碳纳米管之间的连接。羟基（-OH）基团的伸缩振动明显增强，激活了碳纳米管的表面，增加了碳纳米管表面Ag⁺形核的数量。在260 ℃以下，Ag/MWCNTs复合材料的质量损失小于MWCNTs的质量损失。最后，制备了银-环氧树脂浆料，发现使用Ag/MWCNTs复合物制备的浆料具有最低的电阻率和最高的热导率。     

Photocatalytic degradation of 2,4-dinitrophenol (DNP) by multi-walled carbon nanotubes (MWCNTs)/TiO2 composite in aqueous solution under solar irradiation

Nanosized multi-walled carbon nanotubes (MWCNTs)/TiO₂ composite and neat TiO₂ photocatalysts were synthesized by sol-gel technique using tetrabutyl titanate as a precursor. The as prepared photocatalysts were characterized using XRD, SEM, FTIR and UV-vis spectra. The samples were evaluated for their photocatalytic activity towards the degradation of 2,4-dinitrophenol (DNP) under solar irradiation. The results indicated that the addition of an appropriate amount of MWCNTs could remarkably improve the photocatalytic activity of TiO₂. An optimal MWCNTs:TiO₂ ratio of 0.05% (w/w) was found to achieve the maximum rate of DNP degradation. The effects of pH, irradiation time, catalyst concentration, DNP concentration, etc. on the photocatalytic activity were studied and the results obtained were fitted to the Langmuir-Hinshelwood model to study the degradation kinetics. The optimal conditions were an initial DNP concentration of 38.8 mg/L at pH 6.0 with catalyst concentration of 8 g/L under solar irradiation for 150 min with good recyclisation of catalyst. The degree of photocatalytic degradation of DNP increased with an increase in temperature. The MWCNTs/TiO₂ composite was found to be very effective in the decolorization and COD reduction of real wastewater from DNP manufacturing. Thus, this study showed the feasible and potential use of MWCNTs/TiO₂ composite in degradation of various toxic organic contaminants and industrial effluents.     

Achieving β-phase poly(vinylidene fluoride) from melt cooling: Effect of surface functionalized carbon nanotubes

Poly(vinylidene fluoride) (PVDF) based nanocomposites with different surface-functionalized multi-walled carbon nanotubes (MWCNTs) were prepared by melt mixing in a small scale compounder. With the incorporation of commercial functionalized MWCNTs, the β-phase in PVDF can be directly achieved from melt cooling, as verified by results of Fourier transform infrared spectrum and X-ray diffraction. Interestingly, nanocomposites with amino group functionalized MWCNTs showed the highest percentage of β-phase (17.4%) formation in PVDF, followed by those with hydroxyl groups (11.6%) and unmodified MWCNTs (9.4%). However, the nanocomposites containing MWCNTs with carboxyl groups which were thought to be able to well interact with the dipoles on PVDF chains have the lowest amount of β-phase, i.e. 4.7%. The analysis on the mechanism of the influence of surface functionalization of MWCNTs on the formation of β-phase in PVDF shows that the combined effects of the dispersion of MWCNTs and the nanotube–polymer interactions account for the formation of the β-phase in PVDF.     

Characterization of the surface energies of functionalized multi-walled carbon nanotubes and their interfacial adhesion energies with various polymers

The surface energies of pristine multi-walled carbon nanotubes (MWCNTs) and MWCNTs functionalized with carboxylic acid (MWCNT-COOH), acyl chloride and ethyl amine were characterized, and the effects of the changes in MWCNT surface energies on the interfacial adhesion and reinforcement of the composites were explored. When the surface energy of pristine MWCNTs was compared to that of functionalized MWCNTs, a decrease in the dispersive surface energy and an increase in the polar surface energy were observed. Interfacial adhesion energies between MWCNTs and various polymers were estimated from surface energy values of MWCNTs and various polymers. Among the MWCNTs, polyethylene, polystyrene and bisphenol-A polycarbonate (PC) had the highest interfacial energy with pristine MWCNTs, while nylon 6,6 and polyacrylamine exhibited the highest interfacial energy with MWCNT-COOH. When tensile properties and adhesion at the interface of PC and nylon 6,6 composites containing MWCNTs were examined, composites having high interfacial adhesion energy exhibited greater adhesion at the interface and reinforcement.     

一维多壁碳纳米管增强丁基橡胶/聚丙烯热塑性弹性体复合材料的相态结构及热电性能研究

制备一维多壁碳纳米管(MWCNTs)增强丁基橡胶(IIR)/聚丙烯(PP)动态硫化热塑性弹性体(TPV)复合材料,研究IIR/PP用量比(简称橡塑比)对复合材料相态结构、介电性能、导热性能和物理性能的影响。结果表明:复合材料呈现“海-岛”相结构,IIR相以微米级交联颗粒分散在PP相中;MWCNTs主要分散在PP中,随着橡塑比的增大,MWCNTs有少量团聚现象;随着橡塑比的增大,复合材料的交流电导率、介电常数和热导率增大,且橡塑比大于6/4时增速减小;随着橡塑比的减小,复合材料的拉伸强度先增大后减小;当橡塑比为5.5/4.5时,复合材料的物理性能较好。     

Effects of MWCNTs on improving the hydrogen storage performance of the Li3N system

In this paper, the influence of multi-walled carbon nanotube (MWCNT)-doping on the hydrogen storage properties of the Li₃N system was systematically investigated. Compared with the pure Li₃N sample, the MWCNT-doped Li₃N sample shows faster hydrogen absorption and desorption kinetics and a drastically improved cycling stability. Along with increasing MWCNT content, the hydrogen storage improvement becomes more apparent. When the MWCNT doping level reaches 10 mol%, the enhancement effect is significant. The improved hydrogen storage properties of the Li₃N system by MWCNT-doping can be reduced to the physical effect of ball milling, the increased specific surface area and large pores as well as the good thermal conductivity of MWCNTs.     

Microstructures and enhanced flexural properties of single-crystalline HfC nanowires in-situ modified carbon/carbon composites by electrophoresis-thermal evaporation using CNTs as the template

To improve the mechanical properties of carbon/carbon (C/C) composites, in-situ synthetized single-crystalline hafnium carbide nanowires (HfCnws) were introduced into the carbon fiber preforms by electrophoresis-thermal evaporation method. The Multi-walled carbon nanotubes (MWCNTs) were utilized as the carbon source and templates for forming HfCnws. The microstructure, chemical composition and mechanical properties of the HfCnws modified carbon/carbon (HfCnws-C/C) composites were characterized. Results reveal that HfC is produced preferentially in the inner nodular parts and end parts of MWCNTs. The raising heat-treatment temperature would influence the diffusion rate of Hf atoms and then the number of nucleation sites, which further changed the aspect ratio and morphology of HfCnws. The HfCnws have refined the grain size of pyrolytic carbon (PyC), and significantly improve the flexural strength of C/C composites by 79.3%.