网络化制造中基于STEP-NC的编程方法

STEP-NC是由欧美提出的新的数控接口标准，目的是取代旧的数控标准ISO6983。本文首先分析了STEP-NC的两种应用标准：ISO14649（ARM）和STEPAP238（AIM），并且分析了Part21和Part28的应用领域及Part21文件格式和其中的信息产生方法。然後介绍了ST-Developer环境下ROSEC＋＋颠库编程接口及其应用程序的早、晚编联方式，并且以此为基础设计了整个程序的编程流程，重点介绍了工艺规划设计。最后给出了在C＋＋编程环境下利用ROSE库函数写入形成STEP AP238文件的方法。     

IF板与08Al板的成形性能研究

通过模拟成形性试验，对新型超深冲用IF钢板和传统冲压用08Al钢板的冲压成形性能进行了研究．结果表明：IF板的拉深性能、扩孔性能、胀形性能以及“拉深-胀形”复合性能等均优于08Al板，其中，扩孔性能和平面各向异性的改善最为显著；各项试验中，IF板的成形力普遍小于08Al板。     

变形温度和变形程度对Ti－31合金性能和组织的影响

通过高温和室温拉伸试验，研究了变形温度和变形程度对Ｔｉ－３１合金板材性能和组织的影响。结果表明，合金在７５０～８５０℃的温度下变形５％～２０％空冷后，其室温机械性能均能达到材料的技术指标要求。并发现了材料在９００℃的临界变形区。     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

数控加工的基本坐标系和对刀问题

数控加工中的对刀问题影响机械加工的各个方面。这里从介绍数控机床的基本坐标系出发，重点阐述了对刀的基本原理和方法以及常见数控机床对刀问题的处理。     

关于粉体成球机盘体几何形状的研究

通过对粉体小球在粉体成球机盘底上运动轨线的研究,利用Euler定理,结合其参数特点,得到了不同几何形状的盘底在成球过程中对粉体小球运动的影响,球面盘底较平面盘底更有利于成球的结论。     

翻领成型器领口曲线的程序计算展开法

根据翻领成型器领口曲线的数学模型，介绍一种利用计算器复杂公式存贮的特殊功能，预编程序计算相关参数。然后画领口曲线展开图的方法。     

工业产品的艺术造型与技术美学

本文从技术美学的角度，广义的介绍了工业产品艺术造型的基本方法，着重从美学原则和色彩设计两方面论述产品造型设计的手法，以及技术美学在产品造型设计中的基本应用。     

多功能滚齿机的数字控制系统

本文叙述了以ＳＴＤＰＣ／ＸＴ（或ＰＣ／ＡＴ）机为主要核心构成的滚齿机数字控制系统的结构，软件设计和特点，系统采用混合语言编程，极大地提高了软件设计的灵活性与快速性，也分析了ＣＮＣ系统的加工过程，提出了加工中的软件预处理控制方法，并给出了轴伺服控制的并行算法分析与实现。     

Effect of Forming Pressure on the Internal Structure of Alumina Green Bodies Examined with Immersion Liquid Technique

Green bodies prepared by compaction of alumina granules were made transparent by an immersion liquid technique, and the internal structure was characterized with an optical microscope to study the effect of forming pressure on the internal structure. Clear images obtained by the technique provide more detailed information than other existing methods for structures ranging from one to tens of micrometers. Intergranular pores were present between unfractured granules. Their sizes and concentration tended to decrease with increasing forming pressure. However, pores were clearly present even in the green body prepared at 600 MPa. A rod- and needlelike feature was also found and was concluded to correspond to a high-density region. The significance of large pores and high-density regions on processing as well as the details of the technique is discussed.