Revealing the relationships between alloy structure,composition and plastic deformation in a ternary alloy system by a combinatorial approach

A high-throughput approach based on magnetron co-sputtering of alloy libraries is employed to inves-tigate mechanical properties of crystalline and amorphous alloys in a ternary palladium(Pd)-tungsten(W)-silicon(Si)system with the aim to reveal the difference in plastic deformation response and extract the relevant structure-property relationships of the alloys in the system.It was found that in contrast to crystalline alloys,the amorphous ones,i.e.,metallic glasses,exhibited a much smaller fluctuation range in the plasticity parameters(Er2/H and Wp/Wt),indicating a significant difference in the plastic deformation mechanism controlling the mechanical properties for the respective alloys.We propose that the inho-mogeneous deformation of amorphous alloys localized in thin shear bands is responsible for the weaker compositional dependence of both plasticity parameters,while dislocation gliding in crystalline materials is significantly more dependent on the exact structure,thus resulting in a larger scattering range.Based on the representative efficient cluster packing model,a set of composition-dependent atomic structural models is proposed to figure out the structure-property relationships of amorphous alloys in Pd-W-Si alloy system.     

Densification mechanism and microstructure characteristics of nano- and micro- crystalline alumina by high-pressure and low temperature sintering

Fully dense ceramics with retarded grain growth can be attained effectively at relatively low temperatures using a high-pressure sintering method. However, there is a paucity of in-depth research on the densification mechanism, grain growth process, grain boundary characterization, and residual stress. Using a strong, reliable die made from a carbon-fiber-reinforced carbon (C_f/C) composite for spark plasma sintering, two kinds of commercially pure α-Al₂O₃ powders, with average particle sizes of 220 nm and 3 μm, were sintered at relatively low temperatures and under high pressures of up to 200 MPa. The sintering densification temperature and the starting threshold temperature of grain growth (T_sg) were determined by the applied pressure and the surface energy relative to grain size, as they were both observed to increase with grain size and to decrease with applied pressure. Densification with limited grain coarsening occurred under an applied pressure of 200 MPa at 1050 °C for the 220 nm Al₂O₃ powder and 1400 °C for the 3 μm Al₂O₃ powder. The grain boundary energy, residual stress, and dislocation density of the ceramics sintered under high pressure and low temperature were higher than those of the samples sintered without additional pressure. Plastic deformation occurring at the contact area of the adjacent particles was proved to be the dominant mechanism for sintering under high pressure, and a mathematical model based on the plasticity mechanics and close packing of equal spheres was established. Based on the mathematical model, the predicted relative density of an Al₂O₃ compact can reach ～80 % via the plastic deformation mechanism, which fits well with experimental observations. The densification kinetics were investigated from the sintering parameters, i.e., the holding temperature, dwell time, and applied pressure. Diffusion, grain boundary sliding, and dislocation motion were assistant mechanisms in the final stage of sintering, as indicated by the stress exponent and the microstructural evolution. During the sintering of the 220 nm alumina at 1125 °C and 100 MPa, the deformation tends to increase defects and vacancies generation, both of which accelerate lattice diffusion and thus enhance grain growth.     

Fully renewable limonene‐derived polycarbonate as a high‐performance alkyd resin

Limonene‐derived polycarbonate‐based alkyd resins (ARs) have been prepared by copolymerization of limonene dioxide with CO₂, catalysed by a β‐diiminate zinc–bis(trimethylsilyl)amido complex, and subsequent chemical modification with soybean oil fatty acids using triphenylethylphosphonium bromide as the catalyst. This quantitative partial modification was realized via epoxy–carboxylic acid chemistry, affording ARs with higher oil lengths, lower polydispersities and higher glass transition temperatures (T_g) in comparison to a conventional polyester AR based on phthalic acid, multifunctional polyol pentaerythritol and soybean fatty acid. The novel limonene polycarbonate AR and the conventional polyester AR were evaluated as coatings and both the physical drying (without the presence of the oxidative drying accelerator Borchi® Oxy Coat) and chemical curing (with Borchi® Oxy Coat) processes of these coatings were monitored by measuring the König hardness and complex modulus development with time. A better performance was obtained for the alkyd paint containing polycarbonates modified with fatty acids (FA‐PCs), which showed a faster chemical drying, a higher König hardness and a higher T_g in coating evaluation, demonstrating that the fully renewable FA‐PCs are promising resins for alkyd paint applications. © 2019 Society of Chemical Industry     

Effect of Bimodal Grain Size Distribution on the Strain Hardening Behavior of a Medium-Entropy Alloy

The evolution of strain hardening behavior of the Fe_(50)(CoCrMnNi)_(50) medium-entropy alloy as a function of the fraction of recrystallized microstructure and the grain size was studied using the Hollomon and Ludwigson equations.The specimens under study were partially recrystallized,fully recrystallized with ultrafine-grained microstructure,and fully recrystallized with coarse grains.The yield strength decreases steadily as the fraction of recry stallized micro structure and grain size increases due to the recovery process and the Hall-Petch effect.Interestingly,the bimodal grain distribution was found to have a significant impact on strain hardening during plastic deformation.For instance,the highest ultimate tensile strength was exhibited by a 0.97 μm specimen,which was observed to contain a bimodal grain distribution.Furthermore,using the Ludwigson equation,the effect of the bimodal grain distribution was established from the behavior of K_2 and n1 curves.These curves tend to show very high values in the specimens with a bimodal grain distribution compared to those that show a homogenous grain distribution.Additionally,the bimodal grain distribution contributes to the extensive L(u|")ders strain observed in the 0.97 μm specimen,which induces a significant deviation of the Hollomon equation at lower strains.     

Do people put more value on electricity produced using waste-to-hydrogen? Findings from South Korea

South Korea is pushing for the waste-to-hydrogen (W2H) project to reduce greenhouse gases and utilize plastic and vinyl waste (PVW) while reducing environmental pollution from PVW. This research seeks to estimate additional willingness to pay (WTP) for electricity produced using W2H over that produced using traditional power sources, such as coal and nuclear. For the purpose of the estimation, a contingent valuation survey of 1000 people was performed employing the closed-ended one-and-one-half-bound question during November 2020. A spike model is utilized to reflect zero WTP values that a number of interviewees reported in the survey. Several factors affecting the additional WTP were also analyzed to derive implications. The average WTP was computed as KRW 27.7 (USD 0.025) per kWh with statistical significance, which reaches 26.4% of the electricity price. One more point to note is that 54.3% of the respondents stated a zero WTP as they thought that W2H is of no value to them or were worried that the W2H project could increase electricity bills.     

Measurements and modeling of absorptive partitioning of volatile organic compounds to painted surfaces

Partitioning to surfaces is an important sink for volatile organic compounds (VOCs) indoors, but the mechanisms are not well understood or quantified. Here, a mass spectrometer was coupled to a portable surface reactor and a flow tube to measure partitioning of VOCs into paint films coated onto glass or wallboard, and their subsequent diffusion. A model was developed to extract values of the effective absorbing organic mass concentration of the film, C_w, which is a measure of absorption capacity, and VOC diffusion coefficients, D_f, from VOC time profiles measured during film passivation and depassivation. Values of C_w agreed well with the value estimated from the paint film mass and flow tube air volume, and D_f values (also measured using attenuated total reflectance-Fourier transform infrared spectroscopy) correlated well with VOC vapor saturation concentrations, C*, estimated using a group contribution method. The value of these relationships for estimating key parameters that control VOC partitioning into paint and the fate of VOCs indoors was demonstrated using a house model, which indicated that >50% of VOCs with C* ≤10⁸ μg/m³ (C* of octane, hexanone, and propanol) that contacted a paint film of typical thickness fully permeated the film regardless of emission duration.     

汽车水性金属闪光底色漆的研制与应用

以水性饱和聚酯树脂为基体树脂,以甲醚化氨基树脂为交联剂,以水性闪光铝银粉为效应颜料,以改性乙烯-醋酸乙烯共聚物蜡乳液为定向排列剂,在基材润湿剂、消泡剂、流平剂、中和剂、增稠剂、助溶剂、去离子水等的配合下制得水性金属闪光底色漆。涂膜于160℃×20 min条件下固化,具有VOC(挥发性有机化合物)含量低、硬度高、抗冲击、附着力强、闪光效果好、防腐性能优异、绿色环保、施工安全方便等优点。     

快速成型技术在塑料模具制造中的应用

介绍了基于快速成型技术的塑料模具的制造,并提出了一些需要解决的问题。     

E?cient Video Cutout by Paint Selection

Video cutout refers to extracting moving objects from videos, which is an important step in many video editing tasks. Recent algorithms have limitations in terms of e?ciency, interaction style, and rob...     

Structural fatigue crack growth on a representative volume element under cyclic strain behavior

By introducing parameters λ and ω into the crack tip field, a unified cyclic stress and strain field was first formulated by using the Hutchinson-Rice-Rosengren (HRR) field and the Rice-Kujawski-Ellyin (RKE) field under plane stress states in the present study. On the basis of the plastic strain energy and the linear damage accumulation, two fatigue crack growth models without any artificial parameters were then proposed from a representative volume element of cyclic strain behavior. The fatigue crack growth model included parameters λ and ω which showed the effect of two singularity fields. In addition, a simplified structural fatigue crack growth model was eventually established in terms of the fatigue life of each point on the crack front and the non-self-similar shape evolution law. Finally, the predictions of models are compared with the experimental data and the agreement is found to be fairly good.