基于网格化的移动通信网络资源与业务发展评估分析

目前移动通信网络建设全面转向5G，4G网络建设投资大幅缩减。为保障4G网络投资效益长远、后续资本开支合理，对现阶段4G网络资源与当地市场发展情况进行合理、精准评估变得尤为重要。通过对特定区域内网络资源与业务发展匹配情况分析，结合市场发展需求，精准定位该区域网络能力提升与业务发展方向的重点。助力打造“技术先进、运营高效、质量领先”的高品质智慧精品网。进而强化“网随业动、业随网进”，驱动“网络优势”转化为“市场优势”。     

磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Study on the blackening phenomenon of leaded glass during microgroove molding using nickel phosphorous mold

Precision glass molding (PGM) is a recently developed method to fabricate glass microgroove components. Lead glass is commonly used as an optical material due to its high refractive index and low transition temperature. A nickel-phosphorous (Ni–P) plated mold is traditionally employed in the PGM process for microstructures optics. However, leaded glass is subject to color change and can blacken during the PGM process, reducing the light transmittance of microgrooves. In this paper, an equation for the redox reaction between Ni and Pb is proposed, which is based on the diffusion of inner Ni atoms to the surface of the mold and the standard electrode potential of the Pb ions in leaded glass. A viscoelastic constitutive model of the glass is established to simulate the compression stress distribution during molding. Finally, the effects of molding pressure, molding temperature, and mold material on glass blackening are studied. The results show that the blackening of leaded glass is caused by Pb enriching the surface. The rise in molding stress and temperature increases the deformation of Ni–P plating, which promotes the diffusion of Ni atoms. By adding a titanium incorporated diamond-like carbon (Ti-DLC) coating, the deformation of the Ni–P plating during molding is suppressed, and the diffusion of Ni atoms can be prevented. In this way, the blackening of leaded glass can be prevented.     

Investigation of the influence of iron-containing abrasives on the corrosion behaviour of the aluminium alloy AlSi1.2Mg0.4

The corrosion resistance of aluminium surfaces is closely linked to the surface state after a grinding process. For years, iron-containing abrasive materials were suspected to lead to increased corrosion susceptibility after processing of aluminium surfaces. To prove a possible correlation between the iron content of an abrasive and the corrosion behaviour of aluminium components, scientific investigations and experimentally practical corrosion tests are necessary. For the current investigation, specimens of a technical Al-Si alloy from the same batch were used. The test specimens were mechanically ground with various resin-bonded model abrasives containing different iron contents. The performed corrosion tests did not reveal a negative influence of the different iron-containing abrasives on the corrosion behaviour of the Al–Si alloy. However, the most sensitive measuring method (electrochemical noise) showed differences in the surface activity depending on the type of abrasive.     

Differences between oculomotor and perceptual artifacts for temporally limited head mounted displays

We used perceptual and oculomotor measures to understand the negative impacts of low (phantom array) and high (motion blur) duty cycles with a high‐speed, AR‐likehead‐mounted display prototype. We observed large intersubject variability for the detection of phantom array artifacts but a highly consistent and systematic effect on saccadic eye movement targeting during low duty cycle presentations. This adverse effect on saccade endpoints was also related to an increased error rate in a perceptual discrimination task, showing a direct effect of display duty cycle on the perceptual quality. For high duty cycles, the probability of detecting motion blur increased during head movements, and this effect was elevated at lower refresh rates. We did not find an impact of the temporal display characteristics on compensatory eye movements during head motion (e.g., VOR). Together, our results allow us to quantify the tradeoff of different negative spatiotemporal impacts of user movements and make subsequent recommendations for optimized temporal HMD parameters.     

纵轴式掘进机截割头载荷影响因素的仿真分析

针对现有掘进机截割头载荷特性研究方法采用单一影响因素不能全面反映截割头载荷及其波动变化规律的问题,通过分析截割头瞬时载荷,确定了纵轴式掘进机在水平截割工况下截割头载荷的主要影响因素有截割岩石特性、截割头掏槽深度、截割头吃刀深度、截割头转速和截割臂摆速。针对某纵轴式掘进机水平截割工况,采用Matlab对影响截割头载荷的多种因素进行仿真分析,得到了各向载荷及其波动随各因素的变化规律:截割头载荷随着岩壁普氏系数的增大而增加,其中横向阻力增加尤为明显,横向阻力波动程度高于其他方向载荷,且随着岩壁普氏系数的增大呈减小趋势;随着截割头掏槽深度的增加,截割头各向载荷近似呈线性增加,其中升力增加幅度最大,各向载荷波动则随着截割头掏槽深度的增大而减小;随着吃刀深度的增加,截割头载荷总体呈增大趋势,载荷波动程度则随之减小;在截割头转速一定的情况下,截割头载荷均随着截割臂摆速的增加而增大,在同一摆速下,截割头载荷随着截割头转速的减小而增大,横向阻力波动明显高于升力和推进阻力波动,横向阻力和推进阻力波动按截割头载荷规律变化,升力波动则与之相反。截割头载荷波动变化规律与截割头载荷变化规律不尽一致,有时甚至相互冲突。因此,掘进机作业过程中应合理选择截割头掏槽深度、吃刀深度等操作参数和截割头转速、截割臂摆速等运动参数,使各参数相互匹配,以减小掘进机振动,延长使用寿命。     

热轧带钢卷取机夹送辊修复材料与再制造工艺研究

为了提高热轧带钢卷取机夹送辊表面的修复质量，通过正交试验优选出埋弧堆焊专用焊丝ZJ－11和ZJ－12，过渡层选用ZJ－11药芯焊丝，堆焊硬层选用ZJ－12药芯焊丝，采用优选出的焊丝进行了堆焊修复试验。试验结果显示，堆焊焊缝金相组织中的马氏体更加细化，且碳化物颗粒明显增加，材料的硬度与耐磨性显著提升。研究表明，通过采用合理的再制造工艺对热轧带钢卷取机夹送辊进行修复，修复后满足要求，使用效果良好，显著提高了夹送辊的使用寿命。     

Suppression of forced vibration due to chip segmentation in ultrasonic elliptical vibration cutting of titanium alloy Ti–6Al–4V

Ultrasonic elliptical vibration cutting of titanium alloy Ti–6Al–4V is investigated in this research. Because products made of Ti–6Al–4V alloy are usually designed for possessing low-rigidity structures or good-quality cut surfaces, machining requirements such as low cutting forces and slow rate of tool wear need to be fulfilled for realization of their precision machining. Therefore, the ultrasonic elliptical vibration cutting is applied as a novel machining method for those products. Machinability of Ti–6Al–4V alloy by the ultrasonic elliptical vibration cutting with cemented carbide tools is examined to figure out suitable cutting conditions for precision machining of Ti–6Al–4V alloy. As experimental results, generated chips, cutting forces, and profiles of cut surfaces are indicated. A forced vibration problem occurred due to the segmented chip formation, which is also well-known in the ordinary non-vibration cutting. Therefore, characteristics of the forced vibration due to the chip segmentation are investigated in this research. Through the experiments, it is found that the frequency and magnitude of the forced vibration have relation with the average uncut chip thickness and cutting width. Especially, it is found that the averaging effect can suppress the forced vibration, i.e. the chip segmentation tends to occur randomly over the large cutting width, and hence the force fluctuations with random phases tend to cancel each other as the cutting width increases relatively against the average uncut chip thickness. Based on the investigations, a new practical strategy to suppress the forced vibration due to chip segmentation is proposed and verified. Using the proposed method significantly decreased cutting forces and good quality of surfaces are obtained when the forced vibration is suppressed compared to the ordinary non-vibration cutting results. Therefore, the results suggest that the precision machining can be realized without sacrificing the machining efficiency by increasing the width of cut and decreasing the average uncut chip thickness.     

Machining accuracy improvement for a dual-spindle ultra-precision drum roll lathe based on geometric error analysis and calibration

This paper performs a comprehensive analysis and calibration on the geometric error of the ultra-precision drum roll lathe with dual-spindle symmetrical structure and cross slider layout. Firstly, the volumetric error model which contains all geometric errors of the dual-spindle ultra-precision drum roll lathe (DSUPDRL) is developed based on the combination of the homogenous transfer matrix (HTM) and multi-body system (MBS) theory. Secondly, sensitivity analysis for the volumetric error model is conducted to identify the sensitive geometric error components of the DSUPDRL using an improved Sobol method based on the quasi-Monte Carlo algorithm. The result of sensitivity analysis laid the foundation for the subsequent geometric error calibration. Then, some sensitive error components along the X and Z directions are calibrated using a laser interferometer and a pair of inductance displacement probes. Besides the volumetric error model, the concentricity error caused by dual-spindle symmetrical structure is proposed and calibrated by the on-machine measurement using a classic reversal method. Finally, a large-scale roller mold with a diameter of 250 mm and a length of 600 mm is machined using the DSUPDRL after calibration. The experimental result shows that 1.4 μm/600 mm generatrix accuracy is obtained, which validate the effectiveness of the geometric error analysis and calibration.     

150单缸机试验台冷却系统流动与传热计算分析

基于Flowmaster软件建立了150单缸柴油机试验台冷却系统流动与传热模型,并在某大功率发动机上进行了验证。在此基础上分析得到了冷却水温度和流量、气缸套和气缸盖温度变化对冷却水总传热流量的影响规律,以及管道尺寸、壁面粗糙度、冷却水流量对冷却水流动总阻力的影响规律。