辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响

研究辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响。采用3种不同上辊/下辊转速比(ω/ω0,ω为上辊转速,ω0为下辊转速)1:1、1:1.2及1:1.4进行多次试验。结果显示,在最大辊速差条件下(ω/ω0=1:1.4),7075铝板在轧制方向的屈服强度和极限抗拉强度分别提高41.5%和21.9%。此外,当辊速比ω/ω0为1:1.4时,成品轧制板的平均晶粒尺寸减小36%,横剖面平均硬度增加约9.2%。织构研究结果显示,辊速差越大,成品各向同性及硬度越大。然而,采用不同辊速度的连铸连轧会导致变形板伸长率降低约6%。     

Heterogeneously Catalyzed Methanolysis of Gmelina Seed Oil to Biodiesel

The heterogeneous catalysis of transesterification of gmelina seed oil to biodiesel is evaluated. The oil was extracted from the seeds with n‐hexane by solvent extraction and characterized to determine its physiochemical properties. Response surface methodology was applied to optimize the effect of process variables on the biodiesel yield. The base‐activated clay catalyst performed as montmorillonite clay with the characteristic property of a Brønsted acid. It has an improved surface area after activation that enhanced its catalytic activity on transesterification reaction. Under optimal conditions, the biodiesel yield was 70.1 %, thus demonstrating that the model predicted well the biodiesel production.     

Statistical optimization of operating parameters of microbial electrolysis cell treating dairy industry wastewater using quadratic model to enhance energy generation

The performance of Microbial electrolysis cell (MEC) is affected by several operating conditions. Therefore, in the present study, an optimization study was done to determine the working efficiency of MEC in terms of COD (chemical oxygen demand) removal, hydrogen and current generation. Optimization was carried out using a quadratic mathematical model of response surface methodology (RSM). Thirteen sets of experimental runs were performed to optimize the applied voltage and hydraulic retention time (HRT) of single chambered batch fed MEC operated with dairy industry wastewater. The operating conditions (i.e) an applied voltage of 0.8 V and HRT of 2 days that showed a maximum COD removal response was chosen for further studies. The MEC operated at optimized condition (HRT- 2 days and applied voltage- 0.8 V) showed a COD removal efficiency of 95 ± 2%, hydrogen generation of 32 ± 5 mL/L/d, Power density of 152 mW/cm² and current generation of 19 mA. The results of the study implied that RSM, with its high degree of accuracy can be a reliable tool for optimizing the process of wastewater treatment. Also, dairy industry wastewater can be considered to be a potential source to generate hydrogen and energy through MEC at short HRT.     

The effect of biomass feeding location on rice husk gasification for hydrogen production

The objective of this study is to investigate the impact of biomass feeding location on rice husk gasification for hydrogen production. By comparing the results between top-feed and bottom-feed of the feedstock of the fluidized bed biomass gasification at the reaction temperature between 600～1000 °C and ER = 0.2, 0.27, and 0.33 without steam, the optimum low heating value was increase by 2.35 kJ/g-rice husk by the top-feed to gasifier. Although the yield of hydrogen was decreased by 42% for the rice husk gasification by the top-feed operation, the yield of CO, CO2, and CH4 were highly increased, which enhancing the heating value of the effluent gas. The study results suggested the potential route of the biomass gasification at the different feeding location.     

不同段数爆破地震波的反应谱分析

为了研究段数对反应谱特性的影响,基于某石方控制爆破工程爆破振动实测数据,对不同段数爆破振动信号进行了反应谱分析。首先,利用实测的爆破振动速度信号采用直接微分法获得了加速度信号,并利用EEMD分解对加速度信号进行低通滤波去噪处理,获得了准确清晰的加速度曲线。然后,利用精确法求得了不同段数下爆破振动信号的速度反应谱和标准速度反应谱。分析结果表明:不同段数的爆破振动质点峰值速度与速度反应谱的峰值速度并不存在对应关系,因此分段数的选择应综合考虑结构对爆破振动的动态响应。     

Thermal shock response behaviour of carbon fibre reinforced silicon carbide matrix composites prepared by chemical vapour infiltration at different heating rates

The present work investigated the effects of thermal cycles in air on the tensile properties of a two-dimensional carbon fibre reinforced silicon carbide composite (2D C/SiC) prepared by chemical vapour infiltration at different heating rates. The composite was exposed to different cycles of thermal shock between 20 °C and 1300 °C in air. The damage mechanisms were investigated by AE online monitoring and fractured morphology offline analysis. The tensile strength of 2D-C/SiC decreases with increasing thermal cycles. However, the modulus only decrease within 40 cycles. Due to oxidation, with the decrease in heating rate, the residual properties of the material decrease more obviously. Meanwhile, the results of AE online monitoring and fracture analysis show that the matrix damage is more serious at higher heating rate and that more delamination occours in tensile fractures. The above results indicate that for the thermal shock of 2D C/SiC composites in air, oxidative damage plays a key role in the residual properties.     

YOLSO: You Only Look Small Object

Small object detection is challenging and far from satisfactory. Most general object detectors suffer from two critical issues with small objects: (1) Feature extractor based on classification network cannot express the characteristics of small objects reasonably due to insufficient appearance information of targets and a large amount of background interference around them. (2) The detector requires a much higher location accuracy for small objects than for general objects. This paper proposes an effective and efficient small object detector YOLSO to address the above problems. For feature representation, we analyze the drawbacks in previous backbones and present a Half-Space Shortcut(HSSC) module to build a background-aware backbone. Furthermore, a coarse-to-fine Feature Pyramid Enhancement(FPE) module is introduced for layer-wise aggregation at a granular level to enhance the semantic discriminability. For loss function, we propose an exponential L1 loss to promote the convergence of regression, and a focal IOU loss to focus on prime samples with high classification confidence and high IOU. Both of them significantly improves the location accuracy of small objects. The proposed YOLSO sets state-of-the-art results on two typical small object datasets, MOCOD and VeDAI, at a speed of over 200 FPS. In the meantime, it also outperforms the baseline YOLOv3 by a wide margin on the common COCO dataset.     

卫生纸机压榨部运行参数及能效关系分析与优化

通过对纸机压榨部压力和压榨脱水原理的分析，得到出压榨部纸幅干度可作为压榨部的能耗指标，同时确定压榨线压力和纸机车速是压榨部能耗的主要影响因素。结合纸机实际生产测试并记录压榨脱水数据，绘制测试数据曲线图并拟合压榨线压力、纸机车速和出压榨部纸幅干度三者之间的函数关系，最终确定压榨线压力和纸机车速的最优取值范围。通过对测试数据的分析和拟合，控制压榨线压力在90 kN/m、纸机车速在1075 m/min时，纸幅质量可满足正常生产的要求，还可以节约2.1%的电能，实现卫生纸机压榨部的能耗优化。     

腔磁力系统中的诱导透明和快慢光传播

为了在腔磁力系统中实现可控的磁子诱导透明、磁力诱导透明以及快慢光传播,建立了一个混合腔磁力系统.该系统由一个含有YIG球的微波腔和在z方向对球施加一个均匀的偏置磁场组成,并用强泵浦场驱动磁子和弱探测场驱动微波腔.研究表明,通过调节腔与磁子之间的相互作用强度和微波腔与磁子的耗散比,可以增加磁子诱导透明(MIT)、磁力诱导透明(MMIT)的效果和提高快慢光传播的速度.该研究结果可为磁力诱导放大、量子光学操纵和量子信息存储以及灵敏光开关的研究提供参考.     

Strong tribocatalysis of strontium titanate nanofibers through harvesting friction energy for dye decomposition

Friction is a common clean energy and can be harvested and converted into electricity energy via triboelectricity, which can electrochemically drive dye decomposition in theory. In this work, the tribocatalytic Rhodamine B dye decomposition has been experimentally realized in strontium titanate (SrTiO₃) nanofibers, which are synthesized via a hydrothermal method. In the tribocatalytic dye decomposition process, the friction is exerted in the interface between catalyst surface and a polytetrafluoroethylene (PTFE) Teflon rod setup with the different stirring speed. The RhB dye decomposition ratios of SrTiO₃ nanofibers at these stirring speeds of 200 rpm, 400 rpm, 600 rpm, and 800 rpm are respectively 24.2%, 51.8%, 73.9% and 88.6%, yielding to these reaction rate constants of ～0.0112 h^?1, ～0.0260 h^?1, ～0.0562 h^?1 and ～0.0877 h^?1. The main active species, which play an important role in tribocatalytic process, are the superoxide radicals and holes on basis of the active species quenching experiment results. The excellent tribocatalysis activity makes SrTiO₃ nanofibers potential for application in dye wastewater treatment through utilizing the environmental friction energy.