Thermal properties of hierarchical YSZ and LZO ceramic microspheres with multi-scaled voids investigated by using theoretical,experimental and simulation methods

Heat transfer within ceramic feedstock powders is still unclear, which impedes optimization of the thermal and mechanical properties of the thermal sprayed coatings. The microspheres (yttria-stabilized zirconia YSZ and lanthanum zirconate LZO) were prepared via the electro-spraying assisted phase inversion method (ESP). The thermal properties of the two ESP microspheres and a commercial hollow spherical powder (HOSP) were investigated by using theoretical, experimental, and simulation methods. Thermal conductivity of the single microsphere was estimated via a novel nest model that was derived from the Maxwell-Eucken 1 and the EMT model. Thermal conductivity of a single YSZ/LZO-ESP microsphere prepared at 1100–1200 °C was within 0.36–0.75 W/m K, which was ～ 20 % lower than that of a single YSZ-HOSP microsphere with a similar porosity. Heat flux simulation showed that high tortuosity around the multi-scaled voids of the ESP microsphere led to a more efficient decrease in thermal conductivity compared with total porosity.     

Machine fault diagnosis with small sample based on variational information constrained generative adversarial network

In actual engineering scenarios, limited fault data leads to insufficient model training and over-fitting, which negatively affects the diagnostic performance of intelligent diagnostic models. To solve the problem, this paper proposes a variational information constrained generative adversarial network (VICGAN) for effective machine fault diagnosis. Firstly, by incorporating the encoder into the discriminator to map the deep features, an improved generative adversarial network with stronger data synthesis capability is established. Secondly, to promote the stable training of the model and guarantee better convergence, a variational information constraint technique is utilized, which constrains the input signals and deep features of the discriminator using the information bottleneck method. In addition, a representation matching module is added to impose restrictions on the generator, avoiding the mode collapse problem and boosting the sample diversity. Two rolling bearing datasets are utilized to verify the effectiveness and stability of the presented network, which demonstrates that the presented network has an admirable ability in processing fault diagnosis with few samples, and performs better than state-of-the-art approaches.     

基于改进耦合增强随机共振的滚动轴承故障诊断

针对强背景噪声下经典随机共振方法对滚动轴承故障特征提取效果差的问题,提出了一种基于改进耦合增强随机共振的滚动轴承故障诊断方法。首先,利用一个定参双稳系统和一个变参双稳系统构成耦合随机共振系统,外部输入直接作用于定参双稳系统;然后,通过调节变参双稳系统参数和耦合系数实现耦合系统的随机共振控制,并借助遗传算法实现控制参数的自适应选取。实验和工程应用验证了所提方法的有效性和优越性。     

深井超深井钻井堵漏材料高温老化性能评价

深井超深井钻进裂缝性油气层极易发生频繁的钻井液漏失,造成严重储层损害和重大经济损失。储层段钻进过程中经常发生重复性漏失,意味着仅用酸溶率、粒度分布等常规堵漏材料评价指标已不能满足钻井液漏失控制工程需要。笔者以塔里木盆地克深气田钻井常用的核桃壳、毫米级碳酸钙为研究对象,开展了堵漏材料高温老化评价实验。实验评价结果表明,在180℃的柴油中老化24 h后,核桃壳的颜色由黄色变成黑色,质量损失率为25.16 % ,摩擦系数下降28.24 % ,抗压强度下降21.21 % ;毫米级碳酸钙的颜色由白色变成淡黄色,质量损失率为2.47 % ,摩擦系数下降1.33 % ,抗压强度基本不变;由高温老化后的核桃壳和毫米级碳酸钙所形成的封堵层,其承压能力下降了48.84 % 。分析指出,堵漏材料高温老化失效是深井超深井裂缝封堵层结构破坏并在储层段发生重复性漏失的一个重要因素。     

MC尼龙重载承压地板井下巷道铺设工艺研究

我国煤矿井下无轨运输混凝土路面铺设成本高，并且受开采应力、巷道底板地质条件等影响，其应用受到限制。重载车辆的频繁碾压极易使路面发生损坏，从而影响正常开采效率还带来高昂的维护费用。为解决这一问题，采用MC尼龙重载承压地板代替传统混凝土铺设路面，进行了MC尼龙重载承压地板井下巷道铺设的工艺研究。通过对承压板井下铺设方案的制定、承压地板型式的研发、地板的整体连接及稳定性研发等，实现了高效的作业效率，更为安全、清洁的作业环境以及更低的成本，进而达到了“以塑代混凝土”的实际示范意义。该铺设工艺为井下无轨运输的采区路面、工作面搬家通道、临时路面以及其他应急路面、硐室地板的应用提供了良好的方案借鉴。     

表面织构形状对牙轮钻头轴承摩擦学性能影响的实验研究

牙轮钻头滑动轴承作为钻头破岩过程中传递载荷的关键部件,在低速重载的钻井过程中易发生黏着磨损失效。为改善牙轮钻头滑动轴承的耐磨性能,利用纳秒激光雕刻技术,在牙轮钻头滑动轴承轴颈表面加工了面积比为10%、深度为20μm的圆形、矩形、三角形及复合织构;基于赫兹相似理论,设计近似模拟钻头轴承工况的环-块配对副单元实验方案,并在UMT摩擦试验机上开展织构形状对钻头滑动轴承摩擦副摩擦因数、磨损量、温升变化和微观形貌影响规律的实验研究。结果表明:仿生织构的形状及布置方式对减摩和耐磨效果影响极大,其中圆形、矩形织构的减摩和耐磨性能最优,其次为三角形织构,而复合织构反而增大了摩擦因数及磨损量;单一织构对试件磨损量及温升的影响不大,而复合织构在增加摩擦的同时温度有明显升高,不利于井下高温环境下延长牙轮钻头寿命。     

精密磨床转台静压轴承的强健化设计

针对精密磨床转台静压轴承性能仿真数据与其回转精度实测数据不一致的问题，为提高转台静压轴承的设计水平，提出了静压轴承的强健化设计方法。该方法考虑了轴承结构参数在轴承全生命周期内的变化，分析了半径间隙、油腔尺寸、节流比及润滑油黏度在设计、加工、装配和服役4个阶段的变化规律，重点研究了半径间隙在各阶段对轴承性能造成的影响，给出了转台静压轴承的强健化设计流程。通过一个径向轴承的设计实例对该强健化设计方法进行了说明，并将设计结果与传统设计进行了对比。对比的指标是轴承在4个阶段的刚度、承载力和温升，这3个指标对轴承回转精度有直接影响。研究表明：进行强健化设计后，在生命周期内静压轴承的刚度和承载力的变化量为10%~27%，温度的变化量为0.5%~1.6%，较传统设计更能保证转台回转精度的稳定。     

新型卡板式外径千分表的设计应用

针对机车牵引电机转轴磨削测量中,对转轴轴承位尺寸超差的原因进行分析,设计制作机车牵引电机转轴新型卡板式外径千分表(实用新型:ZL201420477030.7)。实际应用表明,新型卡板式外径千分表保证了牵引电机转轴轴承位的磨削尺寸,避免了转轴轴承位尺寸超差现象,解决了机车牵引电机转轴轴承位磨削测量的工艺、质量问题。     

二里河铅锌矿井下支护方案综述

为总结出一套适合矿山实际的支护方案，二里河铅锌矿在矿山生产的20余年里，引进了多种支护工艺进行试验。矿山根据井巷、硐室所处工程环境，确定了锚杆、钢筋、钢架、混凝土进行单一或组合支护的方案，特别是千枚岩内12.4 m跨度的提升机硐室支护方式与参数，对矿山软弱岩层大跨度硐室工程支护具有参考价值。采场则按照急倾斜、缓倾斜矿体上盘千枚岩支护为例，分别列举了锚杆、锚杆+锚索支护的工程方案。采场联络巷、矿房行人通道等区域利用支柱+横梁临时支护。不但提高了采场作业安全性，也使采矿损失率降低5%，贫化率降低7%。