粉体含能材料生产与储运中的静电安全及防护

分析了静电产生的原因,阐述了粉体含能材料生产中的静电起电现象、静电的危害、静电安全性评估标准以及建立在此标准基础上的静电放电危险的评价办法,提出了粉体含能材料在生产、运输中所需要采取的静电防护措施。     

Stress-strain behavior of geotextile: A proposed new indirect calculation using the static puncture test (CBR test)

Some of the main applications of geosynthetics include use as a hydraulic barrier in sanitary landfills, as a reinforcement element and in pavement engineering. In most cases, these materials are subject to the overlapping effects of tensile strength and puncture. This paper presents a review of indirect methods for calculation of stress and strain averages by means of the California Bearing Ratio (CBR) puncture strength test. In addition, a new calculation method is proposed based on the Kirchhoff plate theory, which interprets the behavior of thin circular plates subjected to a uniform normal loading. This new method enables analysis of the stress-strain in each stretch of the geosynthetic. The methodology is applied to four woven geotextiles of different weights. The results of the new calculation method yielded a better stress-strain correlation with direct tensile strength tests, presenting the smallest relative errors compared to the other indirect calculations reviewed. With the aid of a disk and pins, vertical displacement values at different points in the geotextiles were measured and showed good agreement with analytical predictions. Therefore, the static puncture test combined with the new proposed calculation method is a good alternative for determining the stress-strain parameters of geotextile.     

烯丙基聚烷氧基环氧醚的制备及其性能

针对烯丙基聚烷氧基环氧醚中存在催化剂和钾钠离子含量高,导致制备的三元共聚嵌段硅油反应活性差的问题,研究了在无相转移催化剂的条件下制备烯丙基聚烷氧基环氧醚的方法,表征了产物的结构,分析了制备条件对产物pH值与环氧指数的影响;以其为原料制备了三元共聚嵌段硅油,并对棉织物进行柔软整理,分析了整理后织物的亲水性、手感及物理力学性能。结果表明:当原料烯丙基聚氧乙烯醚、环氧氯丙烷和氢氧化钠的量比为1∶2.5∶1.5,冰醋酸的添加量是过量氢氧化钠的1.1倍时,产物烯丙基聚烷氧基环氧醚的环氧指数为1.77 mol/kg,pH值小于7,精制后钾钠离子含量可降低到5 μg/g以下;织物经过硅油整理后具有较好的亲水性,当整理液质量浓度为30 g/L时,毛效达到7.3 cm,手感评级达到4.7级以上,织物整体性能有所提高。     

静态推靠式旋转导向钻井系统的钻压传递效率

国内研制的静态推靠式旋转导向钻井系统正全面开展现场试验及初步应用,该系统正常钻进时导向翼肋施加到井壁上的静态推靠力会产生较大的摩擦力,有可能影响钻压传递效率和钻井速度。为此,基于该系统的结构及工作原理,考虑井壁无台阶和有台阶两种情况,分别建立了钻压传递效率分析模型,模拟分析了钻压传递效率随名义钻压、井壁摩擦系数,以及导向翼肋推靠力和前倒角的变化规律。研究结果表明:(1)该旋转导向系统对名义钻压有最小值要求,适当提高名义钻压有助于提高钻压传递效率;(2)无论井壁是否有台阶,如果导向翼肋推靠力之和越大、井壁摩擦系数越大,那么钻压传递效率就越低,当井壁有台阶时钻压传递效率明显低于井壁无台阶时的对应值;(3)井壁有台阶时导向翼肋前倒角对钻压传递效率影响明显,前倒角越大则钻压传递效率越低(甚至自锁)。结论认为,该研究成果有助于指导钻井现场合理选择和调控钻压。     

离子交换水软化技术研究与应用进展

离子交换法是目前最常见的水软化技术之一，其基于可逆的离子交换反应将溶液中的硬度离子选择性去除，属于典型的特种分离过程。本文介绍并总结了离子交换水软化的基本原理、水软化用离子交换树脂的结构和分类、离子交换水软化技术研究和应用，并针对离子交换水软化存在的问题提出了相应的解决思路。     

New insight into subcritical rupture of SiC-based filaments at intermediate temperatures (400–900 °C) under air

The delayed failure of SiC fibrous reinforcement has continuously been investigated to warrant the long term performances of Ceramic Matrix Composite (CMC). Chiefly assessed on multifilament tow samples to alleviate some handling difficulties, subcritical crack growth (SCG) parameters are however ruled by structural artifacts which hinder the identification of intrinsic filament behavior. In this paper, we propose to estimate the true filament parameters for 5 fiber types from bundle behavior using a recently communicated Monte Carlo algorithm integrating flaw and stress distributions through a deterministic fracture mechanics law under Paris’ formulation. So computed tow lifetime are broadly dispersed, encompassing raw data, and show a structure-dependent scale effect, revealed by n_filament>n_tow where n is the stress exponent. The relationship between SCG coefficient and chemical composition of the substrate is discussed and highlights the major effect of doping elements (Ti or Zr), oxygen or hydrogen content.     

节理峰前剪切刚度软化模型及其影响因素分析

节理峰前剪切应力-位移曲线是研究节理剪切行为的重要内容。然而目前对于节理峰前剪切行为大多以线性描述,不能较好的描述非线性的特点。对于非线性的描述也仅仅是唯象描述剪切应力-位移曲线,未能反映影响模型的参数物理意义及影响因素。以峰前节理刚度软化行为为出发点,采用归一化的思想将节理剪切刚度与位移无量纲化,用双曲线函数表示出剪切刚度与位移之间的关系。提出了考虑刚度软化的峰前剪切本构关系,通过与试验结果对比验证了本构关系的合理性。影响该模型最重要的两个因素是初始剪切刚度与峰值剪切位移。以Greenwood和Williamson模型为基础在细观上探讨了初始剪切刚度的影响因素;抓住法向应力与节理粗糙度主要因素,探讨了影响峰值剪切位移的影响因素。对模型参数的研究有助于进一步阐明节理峰前剪切机理。     

Multiphonon scattering mechanisms to limit thermal conductivity in weberite RE3NbO7: A case study of (La1-xGdx)3NbO7 ceramics

The management of thermal conductivity is of significant scientific interest, particularly for thermal barrier coatings (TBCs). Multifarious strategies have been used to regulate heat transportation, but it is hard to achieve limit thermal conductivity at elevated temperatures. A systematical investigation of weberite (La_1-xGd_x)₃NbO₇ was thus performed, and multiphonon scattering mechanisms were introduced to achieve limit thermal conductivity (0.92 W m^?1 K^?1). Phonon point defect scattering process accounted for thermal conductivity reduction at low temperatures. Additionally, lattice softening strongly contributed to the reduction of high-temperature thermal conductivity, and solid and stiff chemical bonds were beneficial for inhibiting thermal radiative conductivity. A novel strategy was presented to modify thermal transportation property of weberite RE₃NbO₇ ceramics. Also, the hardness, toughness, and modulus were improved to promote engineering applications of weberite RE₃NbO₇. This study also illuminates novel paths for thermal management and mechanical properties manipulation of TBCs, thermoelectric materials, and microelectronics.     

柔性化夹具静动态特性分析及拓扑优化

针对汽车发动机缸盖、变速箱阀体全自动化混合生产线,设计柔性化夹具来满足CNC高精密加工以及快速换产的要求。建立夹具系统三维模型,并利用ANSYS对夹具系统在不同加工工况载荷下进行静态性能分析;从分析结果判断出影响夹具性能的关键结构,并对其进行拓扑优化设计,实现夹具整体减重39.25 kg。然后对改进后夹具模型进行验证分析,发现最大变形量减少为0.0045199 mm,满足设计指标0.005 mm;最后,对现有夹具系统进行模态实验和CAE模态分析,发现夹具系统在Z向受到低频激振力时,容易发生共振,该频段为70 Hz?110 Hz,在加工过程中需要控制刀具加工频率避免发生共振。     

Compiler compatible 5.66 Mb/mm2 8T 1R1W register file in 14 nm FinFET technology

1-read/1-write (1R1W) register file (RF) is a popular memory configuration in modern feature rich SoCs requiring significant amount of embedded memory. A memory compiler is constructed using the 8T RF bitcell spanning a range of instances from 32 b to 72 Kb. An 8T low-leakage bitcell of 0.106 μm² is used in a 14 nm FinFET technology with a 70 nm contacted gate pitch for high-density (HD) two-port (TP) RF memory compiler which achieves 5.66 Mb/mm² array density for a 72 Kb array which is the highest reported density in 14 nm FinFET technology. The density improvement is achieved by using techniques such as leaf-cell optimization (eliminating transistors), better architectural planning, top level connectivity through leaf-cell abutment and minimizing the number of unique leaf-cells. These techniques are fully compatible with memory compiler usage over the required span. Leakage power is minimized by using power-switches without degrading the density mentioned above. Self-induced supply voltage collapse technique is applied for write and a four stack static keeper is used for read Vmin improvement. Fabricated test chips using 14 nm process have demonstrated 2.33 GHz performance at 1.1 V/25 °C operation. Overall V_min of 550 mV is achieved with this design at 25 °C. The inbuilt power-switch improves leakage power by 12x in simulation. Approximately 8% die area of a leading 14 nm SoC in commercialization is occupied by these compiled RF instances.