C105管桩混凝土设计参数取值的探讨

通过试验得出了C105混凝土100 mm×100 mm×100 mm立方体非标准试件抗压强度换算系数以及C105混凝土的标准方差和强度变异系数。采用理论计算,得到了棱柱体抗压强度与立方体抗压强度的比值α_c1,并与试验实测平均值进行了比较,验证了理论计算方法的可行性。此外,通过对比分析,探讨了直接外延法和引用公式法两种C105混凝土设计参数计算方法的正确性,研究结果可为C105管桩混凝土的设计和应用提供参考。     

Thermal shock effects on the impact resistance,tolerance and flexural strength of alumina based oxide/oxide ceramic matrix composites

In this study the effects of thermal shock on the impact damage resistance, damage tolerance and flexural strength of Nextel 610/alumina silicate ceramic matrix composites were experimentally evaluated. Composite laminates with balanced and symmetric layup were gradually heated to 1200°C in an air-based furnace and held for at least 30 min before being removed and immersed in water at room temperature. The laminates were then subjected to low velocity impacts via a hemispherical steel impactor. The resultant damage was characterized non-destructively, following which the laminates were subjected to compression tests. Three-point bend tests were also performed to evaluate the effect of thermal shock on the flexural strength and related failure modes of the laminates. Thermally shocked laminates showed smaller internal damage and larger external damage areas in comparison to their pristine counterparts. For the impact energy and resultant damage size considered, the residual compressive strengths for the thermally shocked and pristine laminates were similar.     

Reconstruction and hydration of hydrotalcite response to thermal activation temperature: Enhancement of properties for magnesia castables

Optimization binding system for refractory castables is significant to enhance the service performance. Hydrotalcite has been considered a promoter for high-temperature performance of basic castables, however, its binding property remains to be improved before practical application. In this work, the thermal activated Mg–Al hydrotalcites were incorporated in magnesia castables, and the mutual influence of pre-calcination temperature on the hydration, microstructure, and strength of castables was investigated. The obtained results indicated that the reconstruction of calcined hydrotalcite took place in the hydration process and effectively motivated the hydrolysis. Hydrate was thus promoted and a relatively dense microstructure of magnesia castables was confirmed by X-ray computed tomography analysis. Hydrotalcite pre-calcinated at 300 °C contributed to the highest early strength for castable, and the high-temperature properties also performed better than that of other pre-calcinated hydrotalcite-adding. The enhancement mechanisms of calcined hydrotalcite were attributed to the two following reasons: (ⅰ) the modified microstructure of magnesia castables from the early stage by hydration process, (ⅱ) the further enhanced sinterability inspired by the appropriate thermal activation effect.     

Fabrication of Al2O3–ZrO2 ceramics with high porosity and strength

This study describes the synthesis of ceramics, in which a micrometre-sized Al₂O₃–ZrO₂ nanopowder was used as an oxide base for the hardening of the materials. To a suspension of this mixed metal oxide, the pore-forming crystallisation additives camphor and carbamide were added to produce ceramics with thin permeable pores. Camphor crystallised in the oxide suspension in the form of single pentagonal stars and сarbamide crystallised in the form of thin elongated needles. The use of the different crystallisation additives allowed the formation of ceramics after sintering that have both permeable and complex pore morphologies, where anisotropic properties were observed using carbamide as an additive but not when camphor was used. The total porosity of the resulting ceramics was 51.3%, with a compressive strength in the range of 17.3–92.3 MPa.     

Anisotropic strength and fracture resistance of epoxy-ceramic composite materials produced by ultrasound freeze-casting

The anisotropic mechanical properties of ultrasound freeze cast epoxy-ceramic composite materials were studied by measuring flexural strength and fracture resistance curves (R-curves) using both unnotched and notched three-point beam bending experiments, respectively, cut in three different orientations relative to the directional freezing axis. Three ultrasound frequencies of 0.699, 1.39 and 2.097 MHz were used in order to introduce different length scales into the microstructure, with 0 MHz used as the control samples. For all cases, the composites showed higher strength and fracture resistance when the crack plane cut across the direction of ice growth (denoted as the YX orientation). The anisotropic properties were more evident for the material produced without ultrasound (0 MHz) where the flexural strength was approximately 160% higher for the YX orientation compared to two orthogonal orientations. Most of the fracture resistance increase was found to occur within a crack extension, Δa, of ～0.5 mm. Comparing the fracture resistance at Δa = 0.5 mm for the highly anisotropic 0 MHz samples showed that the YX orientation was approximately 86% tougher than the two orthogonal orientations. When the ultrasound operation frequencies of 0.699, 1.39 and 2.097 MHz were applied, the amount of anisotropy in the strength and fracture resistance gradually decreased as the operating frequency increased. The high strength and fracture resistance for the YX orientation was attributed to the alignment of the ceramic particles along the freeze front direction creating a barrier for crack propagation. Ultrasound modifies the material microstructure, introducing relatively dense ceramic layers perpendicular to the freezing front direction that act as an additional, orthogonal barrier to crack propagation. The addition of the denser layers acts to improve the mechanical properties in the weaker orientations and reduce the overall anisotropy.     

Effects of light crude oil contamination on the physical and mechanical properties of geopolymer cement mortar

Fly ash and oil contaminated sand are considered as the two waste materials that may affect environment. This paper investigated the suitability of producing geopolymer cement mortar using oil contaminated sand. A comparison between physical and mechanical properties of mortar produced using geopolymer and Ordinary Portland Cement (OPC), in terms of porosity, hydration and compressive strength, was conducted. The results showed that heat curing can increase the compressive strength of geopolymer mortar up to 54% compared to ambient curing situation. The geopolymer mortar with 1% of light crude oil contamination yielded a 20% higher compressive strength than OPC mortar containing sand with a saturated surface dry condition. Furthermore, the formation of efflorescence decreased as the level of oil contamination decreased. Moreover, the heat curing method increased the kinetic energy and degree of reaction for geopolymer cement mortar, which cause an increment of the density of the pore system and improving the mechanical properties of the resulting composites. From the results of this study, it was demonstrated that geopolymer mortar has the potential of utilizing oil contaminated sand, and reducing its environmental impacts.     

SWRH82B钢Φ14 ~ 15 mm盘条的生产实践

采用Cr、V微合金化技术开发了抗拉强度≥1180 MPa的SWRH82B钢Φ14～15 mm盘条(/%:0.79～0.82C,0.15～0.35Si,0.60～0.90Mn,≤0.025P,≤0.006S,≤0.015As,0.26～0.32Cr,0.04～0.07V)。水钢用100 t转炉-LF精炼-160 mm×160 mm连铸(结晶器带电磁搅拌)-铸坯缓冷-高速线材轧制-Stellmor风冷的工艺流程生产的SWRH82B钢Φ14～15 mm盘条组织的索氏体化率达到了95%。盘条的抗拉强度为1 180～1 270 MPa,断面收缩率为27.0%～37.5%。盘条满足大规格高强度矿用钢绞线的要求。     

Three-parameter (3P) weibull distribution for characterization of strength of ceramics showing R-Curve behavior

Strength distribution of advanced ceramics is commonly characterized by two-Parameter (2P) Weibull distribution. However, deviation of strength distribution from 2P-Weibull distribution may occur in ceramics due to various mechanisms. R-curve behavior is one of these mechanisms where increase of fracture resistance with the extension of crack occurs. In such cases, 2P-Weibull distribution may not be the best fitting distribution function based on the goodness-of-fitness tests. This article examines the effectiveness of three-parameter (3P) Weibull distribution function for fitting the strength variation due to R-curve effect by using experimental and virtual strength data. The effect of Weibull parameters, degree of increase in crack resistance and number of samples on effectiveness of fitting via 3P-Weibull distribution is investigated. It is reported that 3P-Weibull distribution function fits the strength distribution better than 2P-Weibull distribution function for materials showing R-curve behavior when the crack resistance curve is steep and Weibull modulus is high. Furthermore, it is shown that at least 100 samples should be used for a reliable estimate when the material exhibits R-curve behavior.     

Statistics of ceramic strength: Use ordinary Weibull distribution function or Weibull statistical fracture theory?

“Weibull statistics” for strength distribution analysis refers to either the ordinary Weibull distribution function or the Weibull statistical fracture theory. The ordinary Weibull distribution function is an empirical distribution function on an equal footing with other type of classical empirical distributions such as normal and log-normal distributions for fitting the statistical data of various random variables nonexclusive to materials strength. It has no explicit physical meaning and cannot be used for size scaling and prediction of strength. The Weibull statistical fracture theory is a weakest-link statistical fracture model for a solid with the strength distribution of an elemental volume being described by the ordinary Weibull distribution function. It has the capability of size scaling and prediction of strength for specimens with different geometries and different loading modes. The three-parameter Weibull statistical fracture theory in uniaxial flexure of prismatic beams is reformulated and validated by both numerical and real strength experiments of different ceramics.