工艺参数对动态流量控制法挤压弯管应力的影响

采用有限元模拟和实验研究了挤压钛合金弯曲管件。通过实验验证了工件的形状和尺寸精度,并通过有限元模拟分析了工艺参数对挤出过程中变形体的平均压应力分布情况和挤出弯管件的曲率半径的影响规律。结果表明:有限元模拟中,弯管件的曲率半径误差为6.03%,弯管直径误差为3.82%;在靠近定径带处,平均压应力呈非均匀分布;在焊合腔内,靠近细分流孔区域的平均压应力小于靠近粗分流孔区域的平均压应力,平均压应力的大小顺序在通过粗、细分流孔前后相反;在模具结构固定不变时,弯管件的曲率半径随挤压速度的减小而增大,不随挤压温度的变化而变化。     

Damping oscillations in a wire bending process

This paper presents an approach to modify CAD/CAM generated motion profiles for wire bending machines, in order to damp wire oscillations without decreasing machine throughput. Two different methodologies are presented, both leveraging on a simple and easily identifiable model of wire oscillations, the first one based on a filtering approach, the second one on an optimisation approach. The two methodologies are both characterised by a low computational complexity, allowing them to be integrated directly in the bending machine user interface, and can rely on a standard camera to identify wire oscillation parameters. A thorough experimental validation of the approaches is also presented, showing promising results in damping oscillations with wires of different materials.     

基于全U网络的混凝土路面裂缝检测算法

针对现有的混凝土裂缝检测算法在各种复杂环境中检测精度不够、鲁棒性不强的问题,根据深度学习理论和U-net模型,提出一种全U型网络的裂缝检测算法。首先,依照原U-net模型路线构建网络;然后,在每个池化层后都进行一次上采样,恢复其在池化层之前的特征图规格,并将其与池化之前的卷积层进行融合,将融合之后的特征图作为新的融合层与原U-net网络上采样之后的网络层进行融合;最后,为了验证算法的有效性,在测试集中进行实验。结果表明,所提算法的平均精确率可达到83.48%,召回率为85.08%,F1为84.11%,相较于原U-net分别提升了1.48%,4.68%和3.29%,在复杂环境中也能提取完整裂缝,保证了裂缝检测的鲁棒性。     

Thermo-adjusted self-healing epoxy resins based on Diels–Alder dynamic chemical reaction

Micro-damage in materials could be repaired by endowing materials with self-healing performance. Herein, an epoxy resin with excellent self-healing performance grounded on thermo-reversible Diels–Alder dynamic chemical reaction was developed. Results showed that the bending strength and adhesive behavior of epoxy resin were influenced dramatically upon treatment with various temperatures. More importantly, damages created in epoxy resin could be repaired completely after suitable heat treatments. What is more, the healed epoxy resin exhibited much higher bending strength and adhesive performance than the pristine one did. The materials could be damaged and then repaired repeatedly. Meanwhile, the as-prepared self-healing epoxy resin exhibited excellent thermal reversibility and controllable adhesion. The thermo-adjusted self-healing performance endowed epoxy resin with recyclable and reusable performance. Therefore, the research made it possible of recycling waste epoxy resins.     

转锈稳锈材料在石油钻采设备薄壁件表面的应用

石油钻采设备中存在部分薄壁板件(厚度不超过3 mm),在喷砂或喷丸过程中极易造成变形,故实际生产中只能手工打磨清理。但是手工打磨效率较低,且一旦手工清理不彻底,会影响产品的防腐质量。为提升石油钻采设备中薄壁防腐质量,引进了新材料——转锈稳锈材料。通过控制变量,使用拉拔仪检测不同变量下涂层附着力;对转锈稳锈材料和传统的手工处理进行比较,考察其对不同品牌的油漆是否具有兼容性。研究结果表明:转锈稳锈材料与传统的手工打磨清理相比在增加漆膜附着力方面更具有优势,而且与大多数的油漆具有兼容性。     

基于PolyWorks虚拟装配间隙面差计算分析研究

随着当今社会汽车制造业的迅猛发展,高标准和高需求已经是消费者对汽车制造凯歌的主旋律。而这其中,汽车钣金件的间隙面差就是其中一个重要因素。快速检测间隙面差是否满足设计要求直接关系到汽车白车身的生产精度和企业的工作效率。传统计算间隙面差大多利用量具,易划伤被测物且在零件实际装配后才可测量,降低生产效率,而非接触测量造价昂贵。本课题基于实物的汽车钣金件虚拟装配,对间隙面差的计算方法进行分类与参数调整,提出一种高效率、高标准的间隙面差计算流程。     

Flower‐shaped ultra‐wideband fractal antenna

A flower‐shaped ultra‐wideband fractal antenna is presented. It comprises a fourth iterative flower‐shaped radiator, asymmetrical stub‐loaded feeding line, and coplanar quarter elliptical ground planes. A wide operating band of 12.12 GHz (4.58‐16.7 GHz) for S ₁₁ ≤ ? 10 dB is achieved along with an overall antenna footprint of 15.7 × 11.4 mm². In addition, other desirable characteristics, that is, omnidirectional radiation patterns, peak gain upto 5 dB, and fidelity factor more than 75% are achieved. A good agreement exists between the simulation and measured results. The obtained results illustrate that this antenna has wide operating range and compact dimensions than available structures.     

Formation of radioactive cesium microparticles originating from the Fukushima Daiichi Nuclear Power Plant accident: characteristics and perspectives

ABSTRACT

Following identification of radioactive Cs microparticles (CsMPs) in aerosol samples from the Fukushima Daiichi Nuclear Power Plant (FDNPP), numerous reports on CsMPs have been published. This paper reviews recent progress in the measurement and characterization of CsMPs by advanced analytical techniques, including advanced transmission electron microscopy (TEM) and synchrotron X-ray analysis. These analyses revealed that the CsMPs contained Si, Fe, Zn, Cs, and minor quantities of U together with some fission products. Uranium in the CsMPs was identified as being in the form of uraninite and (U,Zr)O₂. Detailed advanced TEM analysis has clarified some of the processes resulting in the alteration of constituents of the nuclear fuels and containment vessel materials during this severe accident. In addition, a detailed report on the elemental compositions and structures of the fuel debris fragments collected inside and outside of the primary containment vessel²⁵ highlighted the fact that the fuel debris fragments contained nanoparticles with the U and Zr components having similar structures to that of the CsMPs. This similarity in structures has stimulated further research on the structure and elemental constituents, especially for U and Zr in the CsMPs, and has opened up new avenues for studying the chemical characteristics of the fuel debris.     

Design of switchable band‐notched frequency selective absorber

An active band‐notched frequency selective absorber (BNFSA) with switchable notch band is proposed in this article. The BNFSA is a two‐layer structure composed of a lossy layer at the top and a ground plane at the bottom, separated by an air spacer. The element of the lossy layer is a lumped‐resistor‐loaded metallic dipole with a parallel LC resonance structure, which is realized by complementary n‐shaped resonator (CnR) inserted in the center, and PIN diode is welded at two arms of CnR. The bias circuit printed on the back of the substrate of the lossy layer connects to anode and cathode of the diode by via hole and isolates by the inductor. Simulation results show that the notch bands are located at 4.50 and 6.81 GHz when the diode sets to ON and OFF, respectively. To validate the performance of switchable BNFSA, the prototypes are fabricated and measured, reasonable agreement between simulated and measured results is obtained.