Fabrication of high-efficiency Yb:Y2O3 laser ceramics without photodarkening

High-efficiency Yb:Y₂O₃ laser ceramics were fabricated using the vacuum-sintering plus hot isostatic pressing (HIP) without sintering additives. High-purity well-dispersed nanocrystalline Yb:Y₂O₃ powder was synthesized using a modified co-precipitation method in-house. The green bodies were first vacuum sintered at a temperature as low as 1430°C and then HIPed at 1450°C. Finally, the samples were air annealed at 800°C for 10 h. Although no sintering aids were used, full density of the samples with excellent optical homogeneity and an inline transmission of 80% at 400 nm could be obtained. Moreover, photodarkening phenomenon was not detected in the ceramics. Preliminary laser experiment with the fabricated ceramics in a two-mirror cavity has demonstrated 32 W continuous-wave (CW) output at ∼1077 nm with an optical-to-optical conversion efficiency of 58.2%. To the best of our knowledge, this is so far the highest CW output power and optical-to-optical conversion efficiency achieved with the Yb³⁺-doped sesquioxide ceramics in a simple two-mirror cavity.     

Achieving fabrication of highly transparent Y2O3 ceramics via air pre-sintering by deionization treatment of suspension

An easy albeit quite effective deionization suspension treatment was adopted to alleviate the detrimental effects related to the hydrolysis of Y₂O₃ in an aqueous medium. Fabrication of highly transparent Y₂O₃ ceramics with a fine grain size via air pre-sintering and post–hot isostatic pressing (HIP) treatment without using any sintering additive was achieved using the treated suspensions. The hydrolysis issue of Y₂O₃ powder in an aqueous medium was effectively alleviated by using deionization treatment, and a well-dispersed suspension with a low concentration of dissolved Y³⁺ species was obtained. The dispersed suspensions were consolidated by the centrifugal casting method, and the green bodies derived from the suspension of 35.0 vol% solid loading showed an improved homogeneity with a relative density of 52.1%. Fully dense Y₂O₃ transparent ceramic with high transparency was obtained by pre-sintering consolidated green compacts at a low temperature of 1400°C for 16 h in air followed by a post-HIP treatment at 1550°C for 2 h under 200 MPa pressure. The sample had a fine average grain size of 690 nm. The in-line transmittance of the sample reached 83.3% and 81.8% at 1100 nm and 800 nm, respectively, very close to the theoretical values of Y₂O₃.     

相变温度附近等温热处理对Mg97Zn1Y2合金组织演化的影响

研究了相变温度附近等温热处理温度和保温时间对含长周期结构Mg97Zn1Y2合金的组织的影响，并对演变机理进行了探讨。主要研究结论如下：500℃固溶处理时，随着时间的增加，长周期结构有增长的趋势。采用等温热处理可以将Mg97Zn1Y2合金中的枝晶组织转变为球状晶，当合金保温温度范围从540℃~600℃时，组织尺寸由大-小-大的顺序变化，即经过了粗化、分离及球化至最后粗化三个过程。在等温热处理温度为575℃的组织大致演变趋势为：枝晶态-不规则球形+块状-球形状，当保温时间15min，其组织为均匀、圆整的球状晶。     

Lipids and Antiplatelet Therapy: Important Considerations and Future Perspectives

Lipids play an essential role in platelet functions. It is known that polyunsaturated fatty acids play a role in increasing platelet reactivity and that the prothrombotic phenotype plays a crucial role in the occurrence of major adverse cardiovascular events. The ongoing increase in cardiovascular diseases’ incidence emphasizes the importance of research linking lipids and platelet function. In particular, the rebound phenomenon that accompanies discontinuation of clopidogrel in patients receiving dual antiplatelet therapy has been associated with changes in the lipid profile. Our many years of research underline the importance of reduced HDL values for the risk of such a rebound effect and the occurrence of thromboembolic events. Lipids are otherwise a heterogeneous group of molecules, and their signaling molecules are not deposited but formed “on-demand” in the cell. On the other hand, exosomes transmit lipid signals between cells, and the profile of such changes can be monitored by lipidomics. Changes in the lipid profile are organ-specific and may indicate new drug action targets.     

Effect of Y concentration and film thickness on microstructure and electrical properties of HfO2 based thin films

In this work, we introduced a simple solution processing method to prepare yttrium (Y) doped hafnium oxide (HfO₂) based dielectric films. The films had high densities, low surface roughness, maximum permittivity of about 32, leakage current < 1.0 × 10^?7 A/cm² at 2 MV/cm, and breakdown field >5.0 MV/cm. In addition to dielectric performance, we investigated the influence of YO_1.5 fraction on the electronic structure between Y doped HfO₂ thin films and silicon (Si) substrates. The valence band electronic structure, energy gap and conduction band structure changed linearly with YO_1.5 fraction. Given this cost-effective deposition technique and excellent dielectric performance, solution-processed Y doped HfO₂ based thin films have the potential for insulator applications.     

Microstructure and flexural strength of the Y:TZP/BG composite

The addition of bioactive glasses to a Y:TZP matrix represents a feasible alternative to provide bioactivity to this material and optimize osseointegration. This work evaluated the effect of the BG concentration (0 and 10 wt%) and the sintering temperature (1200°C and 1300°C) on the microstructure, relative density, and flexural strength of the composite Y:TZP/BG. The Y:TZP and Y:TZP/BG powders were uniaxially pressed and sintered at 1200°C or 1300°C for 1 h. The microstructure was characterized by X-ray diffraction analysis, scanning electron microscopy, and energy-dispersive X-ray Spectroscopy. Relative density was calculated from density values obtained using the Archimedes’ principle. For the flexural strength, specimens (n = 6) were fractured in a biaxial flexural setup using a piston-on-three-balls fixture in a universal testing machine. Bioactivity test was performed in simulated body fluid solution. The results suggested that BG addition decreased the grain size of the composite, increased porosity and caused a significant decrease in the relative density and flexural strength. Crystalline phases of calcium stabilized cubic zirconia and sodium zirconium silicate were formed after the addition of BG. Finally, it was concluded that composite specimens sintered at 1300°C showed the highest density values and larger grains compared to those sintered at 1200°C.     

Y_2P_4O_(13):Eu~(3+)荧光材料的制备及其性能

采用湿化学法制备了Eu~(3+)掺杂Y_2P_4O_(13)荧光材料,通过X射线粉末衍射(XRD)、傅里叶变换红外光谱(FT-IR)和荧光光谱(FL)等手段表征制备产物的物相结构、荧光性能,并对合成原料中稀土与磷的比例(n(Y+Eu)/n(P))和pH调节剂种类对制备样品的物相结构及性能的影响进行分析。结果表明:合成原料中n(Y+Eu)/n(P)比值和pH调节剂种类直接影响着制备产物的物相结构与性能。在n(Y+Eu)/n(P)=12.1、以NH_4HCO_3为pH调节剂调节pH为6的条件下可获得正交晶系的Eu~(3+)掺杂Y_2P_4O_(13)荧光材料。所制备的Y_2P_4O_(13):2at%Eu~(3+)荧光材料在395nm光的激发下可发射出橙红光。     

Effects of Al content on the corrosion properties of Mg–4Y–xAl alloys

The corrosion performances of Mg–4Y–xAl (x = 1, 2, 3, and 4 wt%) alloys in the 3.5% NaCl electrolyte solution are investigated by electrochemical tests, weight loss measurement and corrosion morphology observation. The results indicate that corrosion modes for the alloys are localized corrosion and the filiform type of attack. With Al concentration increasing from 1 to 4 wt%, the corrosion rate of Mg–4Y–xAl alloys decreases firstly and then increases, and WA42 alloy shows the best corrosion resistance. The addition of Al element to Mg–4Y alloys leads to the formation of Al₂Y and Al₁₁Y₃ intermetallic compounds and reduces the proportion of Mg₂₄Y₅ phase. Corrosion resistance of the Mg–4Y–xAl alloys mainly depends on the size and distribution of the second phases. Besides, the addition of excessive Al can greatly consumes the Y element in the matrix, thus leading to a less protective film on the alloys. The effect of the relative Volta potential changes between the second phases and α-Mg on corrosion resistance of Mg–4Y–xAl alloys is insignificant. The main corrosion products of the Mg–4Y–xAl alloys are Mg(OH)₂, Mg₃(OH)₅Cl·4H₂O, Mg_0.72Al_0.28(CO₃)_0.15(OH)_1.98(H₂O)_0.48, and Mg₄Al₂(OH)₁₂CO₃·3H₂O.