高效液相色谱法测定化妆品中依克多因的含量

建立高效液相色谱法测定化妆品中依克多因的分析方法,采用Agilent Poroshell 120 EC-C₁₈色谱柱（100 mm×3.0 mm,2.7μm）分离,以甲醇和p H为3.0的40 mmol/L磷酸二氢钠-10 mmol/L 1-庚烷磺酸钠缓冲溶液梯度洗脱,流速0.8 m L/min,柱温30℃,检测波长210 nm。采用外标法定量测定化妆品中的依克多因含量。结果表明,依克多因在5～800 mg/L的质量浓度范围内呈现良好线性关系,相关系数为0.999 8,方法的检出限和定量限分别为0.3和1.0 mg/L。该方法具有分离效率高、分析时间短、节省溶剂等优点,解决了依克多因在C₁₈色谱柱上保留弱的问题。     

Profiling hot isostatically pressed canister–wasteform interaction for Pu-bearing zirconolite-rich wasteforms

Zirconolite-rich full ceramic wasteforms designed to immobilize Pu-bearing wastes were produced via hot isostatic pressing (HIP) using stainless steel (SS) and nickel (Ni) HIP canisters. A detailed profiling of the elemental compositions of the major and minor phases over the canister–wasteform interaction zone was performed using scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM-EDS) characterization. Bulk sample analyses from regions near the center of the HIP canister were also conducted for both samples using X-ray diffraction and SEM-EDS. The sample with the Ni HIP canister showed almost no interaction zone with only minor diffusion of Ni from the inner wall of the canister into the near-surface region of the wasteform. The sample with the SS HIP canister showed ∼100–120 μm of interaction zone dominated by high-temperature Cr diffusion from canister materials to the wasteform with the Cr predominantly incorporated into the durable zirconolite phase. We also examined, for the first time, changes to the HIP canister wall thickness caused by HIPing and demonstrated that no canister wall thinning occurred. Instead, in the areas examined, the canister wall thickness was observed to increase (up to ∼20%) due to the compression occurring during the HIP cycle. Further, only sparse formation of (Cr, Mn)-rich oxide particles were noted within the HIP canister inner wall area immediately adjacent to the ceramic material, with no evidence for reverse diffusion of ceramic materials. Though the HIP canister–wasteform interaction extends to ∼120 μm when using an SS HIP canister for the system investigated, this translates to <<1 vol.% for an industrial scale HIPed wasteform. Importantly, the HIP canister–wasteform interactions did not produce any obviously less durable phases in the wasteform or had any detrimental impact on the HIP canister properties.     

A novel foam glass obtained from solid waste: A sustainable strategy for application in the degradation of an environmental pollutant

Foams glass were obtained from solid waste of flat glass and exhausted alkaline batteries. The physical, chemical, crystalline and morphological properties of the samples were obtained using the Archimedes principle, X-ray diffractometry (XRD), scanning electron microscopy (SEM). The results revealed glass foams with apparent porosities in the range of 55–64% and apparent densities in the range of 0.40–0.79 g cm^?3. The manganese oxide and graphite contained within the cathode of alkaline batteries acted as both oxidizing agents and as foaming agents. The zinc contained in the anode acted as a pore stabilizing agent and the zinc oxide as a semiconductor material. The foam glass that was composed of flat glass with an anode of Zn and ZnO, and a cathode of Mn₂O₃ and Mn₃O₄ (named An8), showed the greatest potential for heterogeneous photocatalysis, with a maximum efficiency of 95.9% after 3 h of treatment of solution containing dye. These results suggest the feasibility of producing foam glass from waste, as well as its potential application in photocatalytic systems, such as in the low-cost treatment of water.     

Improvement of gaseous bioenergy production from spent coffee grounds Co-digestion with pulp wastewater by physical/chemical pretreatments

Two steps of hydrolysis and anaerobic biogas production processes was investigated in this study. In the first step, subcritical water (SBW) hydrolysis and chemical (acid/alkali) pretreatments were carried out to enhance hydrolysis efficiency by obtaining and analyzing the total volatile fatty acids (TVFA), chemical oxygen demand (COD), and total sugar productions from spent coffee grounds (SCG) hydrolysate. The subcritical water (SBW) hydrolysis under the condition of temperature 150 °C for 30 min can greatly improve the organic matter breakdown and reached the COD concentration of 1010 g/L which was 30% higher than the untreated raw SCG. For chemical pretreatments, it was found that the alkaline hydrolysis of SCG resulted in the greatest total sugar concentration of 181 g/L whereas the operation conditions were 2.0 M NaOH at 60 °C for 1 h. The peak of TVFA concentration 3725 mg/L was found at the acid hydrolysis of SCG with 1.0 M H₂SO₄ acid, 60 °C for 1 h. The optimal biomethane yield of 115 mL/g COD was obtained when 1.0 M H₂SO₄ acid hydrolysate co-digestion with pulp wastewater which increase methane yield production 8 times of raw pulp wastewater. The pretreatment process was confirmed in this study can significant improve the converting of the biowastes to bioenergy efficiency.     

Cheese ripening in nonconventional conditions: A multiparameter study applied to Protected Geographical Indication Canestrato di Moliterno cheese

A multiparameter study was performed to evaluate the effect of fondaco, a traditional ripening cellar without any artificial temperature and relative humidity control, on the chemical, microbiological, and sensory characteristics of Protected Geographical Indication Canestrato di Moliterno cheese. Ripening in such a nonconventional environment was associated with lower counts of lactococci, lactobacilli, and total viable bacteria, and higher presence of enterococci, in comparison with ripening in a controlled maturation room. Moreover, fondaco cheese underwent accelerated maturation, as demonstrated by faster casein degradation, greater accumulation of free AA, and higher formation of volatile organic compounds. Secondary proteolysis, as assessed by liquid chromatography-mass spectrometry of free AA and low molecular weight peptides, did not show any qualitative difference among cheeses, but fondaco samples evidenced an advanced level of peptidolysis. On the other hand, significant qualitative differences were observed in the free fatty acid profiles and in the sensory characteristics. Principal component analysis showed a clear separation of the fondaco and control cheeses, indicating that ripening in the natural room conferred unique sensory features to the product.     

饱和块状混合回填土地基的一维固结分析

用块状渣土置换软弱地基和回填低洼谷地等是处置工程渣土的有效途径。为了分析饱和块状混合回填土地基的固结性状，运用混合物理论建立了其一维固结模型。首先，假定块状土固相和充填土固相之间满足等应变条件，获得了饱和块状混合回填土中各相应变与块状土孔隙变形和充填土孔隙变形的关系式。其次，在小应变条件下，根据自由能势函数方程建立了饱和块状混合回填土的一维线弹性本构方程，再结合达西定律和应力平衡方程获得了一维固结控制方程。再次，利用分离变量法得到一维固结解析解，通过退化本文模型与已有模型进行对比，验证了本文模型的正确性。最后，基于所得解析解，分析了充填土孔隙渗透系数、块状土孔隙渗透系数以及流体交换参数等因素对饱和块状混合回填土地基固结性状的影响。分析结果表明：充填土孔隙渗透系数对饱和块状混合回填土地基整体固结性状起主导作用；在固结初期，块状土超孔压会有一定程度的上升，且3个参数具有相似的作用机理。     

Numerical study of strain development in high-density polyethylene geomembrane liner system in landfills using a new constitutive model for municipal solid waste

Tensile strain development in high-density polyethylene (HDPE) geomembrane (GMB) liner systems in landfills was numerically investigated. A new constitutive model for municipal solid waste (MSW) that incorporates both mechanical creep and biodegradation was employed in the analyses. The MSW constitutive model is a Cam-Clay type of plasticity model and was implemented in the finite difference computer program FLAC?. The influence of the friction angle of the liner system interfaces, the biodegradation of MSW, and the MSW filling rate on tensile strains were investigated. Several design alternatives to reduce the maximum tensile strain under both short- and long-term waste settlement were evaluated. Results of the analyses indicate that landfill geometry, interface friction angles, and short- and long-term waste settlement are key factors in the development of tensile strains. The results show that long-term waste settlement can induce additional tensile strains after waste placement is complete. Using a HDPE GMB with a friction angle on its upper interface that is lower than the friction angle on the underlying interface, increasing the number of benches, and reducing the slope inclination are shown to mitigate the maximum tensile strain caused by waste placement and waste settlement.     

超高效液相色谱⁃四极杆⁃飞行时间质谱对含PET食品接触材料中可迁移非挥发性物质的筛查研究

采用超高效液相色谱⁃四极杆⁃飞行时间高分辨质谱（UPLC⁃Q⁃TOF）对4类不同类型的含聚对苯二甲酸乙二醇酯（PET）材质的食品接触材料在4 %乙酸和50 %乙醇模拟物中的迁移出的非挥发性未知物进行筛查解析。结果表明，产品在4 %乙酸模拟物的迁移风险远小于50 %乙醇模拟物，主要迁移物质为聚合单体形成的寡聚物，抗氧剂、润滑剂、胶黏剂等加工助剂以及生产加工、迁移过程中形成的非有意添加物（NIAS）物质；纯PET材质的产品迁移物质较少，多层复合材料迁移物质较多。复合材质的产品中，PET材质可能在生产时添加了己二酸、癸二酸、新戊二醇等物质，进行了改性处理；此外，部分迁移物质会与模拟物中的乙醇发生反应，生成新的NIAS物质。     

Synthesis of Ti3C2Fx MXene with controllable fluorination by electrochemical etching for lithium-ion batteries applications

Ti₃C₂T_x MXene has attracted remarkable attention due to its promising applications in energy storage and sensors. However, traditional MXene preparation methods used HF as etchant, which was highly toxic and harmful to human and environment. Moreover, the aqueous etchants will also result in the combination of OH, O and F groups on the surfaces, making it difficult to control the varieties and contents of the surface terminations. In this paper, a green and mild electrochemical exfoliation method was proposed to synthesize Ti₃C₂F_x and synchronously control its fluorination degree on the surface. A non-aqueous ionic liquid, [BMIM][PF₆]-based solution was used as electrolyte. The as-prepared Ti₃C₂F_x was fluorinated with the CF and TiF₃ groups, which were electrochemically active and contributed to the excellent cycling stability of the MXene anode-based Li-ion batteries. These findings provided a facile strategy to prepare MXene materials and dope MXene with tailored property for MXene-based energy devices applications.