Ablation behavior of thin-blade co-deposited C/Cx-SiCy composites under the influence of the complex fluid conditions of the oxyacetylene torch

This paper offers a new way of testing the ablation property of material under an oxyacetylene torch using a thin-blade specimen, which costs much less time to reach the maximum temperature and provides a harsh turbulence fluid field that's closer to reality. The thin-blade specimen experiences a higher turbulent intensity than the traditional disk-like specimen, leading to more efficient heat exchange. The fluid field simulation agrees with the testing results. In addition, we manage to synthesize the C/Cx-SiCy composites with the co-deposition chemical vapor infiltration (CVI) method. The C/Cx-SiCy composites exhibit a similar anti-ablation property as C/C composites and consist of enough SiC phase simultaneously, combining the advantages of both C/C composites and C/SiC composites. The thin-blade C/Cx-SiCy composites show a lower linear ablation rate (1.6 μm/s) than C/C composites (4.1 μm/s) and C/SiC composites (19.6 μm/s) during the oxyacetylene test. The glass layer formed on the surface of C/Cx-SiCy could cling to the bulk material instead of peeling off due to the high PyC content in the matrix could protect the SiO₂ from blowing away.     

菌型叶根动叶片叶根叶冠内径向的加工

菌型叶根动叶片是一种新型的动叶片,采用数控铣加工叶根内径向面时留0.1~0.2mm余量,然后在进行叶根内径向磨削,叶冠直接加工到位,没有后序磨削加工,由于叶根叶冠在加工过程中不是一次装夹完成的,根冠存在一定的落差,在后续的装配中容易产生配合间隙,无法达到要求。文中介绍了一种新的加工工艺,解决了这一问题。     

航空发动机复杂扭曲叶片分步电解加工研究

为实现复杂扭曲叶片在较小间隙下的稳定加工,提出了一种分步式电解加工的工艺方法,建立了复杂扭曲叶片小间隙(0.2 mm)和大间隙下(0.5 mm)扭曲流道的流道模型,采用有限元法进行了流场仿真研究,结果表明增加流道间隙可以解决流道中涡流和流场紊乱的问题。开展了复杂扭曲叶片小间隙连续式加工和分步式加工的试验研究。结果表明,采用小间隙连续式加工,当阴极进给至3.8 mm位置时,在叶片排气边靠近叶根流道扭曲处出现短路打火情况;而采用分步式加工方式能够实现加工的顺利进行。     

High-density polyethylene membranes embedded with carboxylated and polyethylene glycol-grafted nanodiamond to be used in membrane bioreactors

In this work, neat and modified nanodiamond (ND) particles were embedded into high-density polyethylene (HDPE) membranes to improve hydrophilicity and antifouling properties. The membranes were prepared via thermally induced phase separation (TIPS) method and used for pharmaceutical wastewater treatment in membrane bioreactors (MBR) system. To prevent the agglomeration of ND, it was modified using two methods: thermal carboxylation (ND-COOH) and grafting with polyethylene glycol (ND-PEG). Membranes with different concentration of ND-COOH and ND-PEG nanoparticles ranging from 0.00 to 1.00 wt % were prepared and characterized using a set of analyses including water contact angle, pure water flux, tensile strength, differential scanning calorimeter, field emission scanning electron microscopy, and energy dispersive X-ray spectroscopy. It was found that the optimum contents of ND-COOH and ND-PEG nanoparticles were 0.50 wt % and 0.75 wt %, respectively. The interfacial interaction between nanoparticles and HDPE matrix was studied based on Pukanzsky model. To examine the performance of membranes, critical flux, filtration experiment in the MBR, and fouling analysis of membranes were carried out. The results showed that among the fabricated membranes, 0.75 wt % HDPE/ND-PEG membrane had the highest water flux and the best antifouling properties. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47914.     

基于儒可夫斯基变换的涡轮钻具叶片设计及性能分析

为提高涡轮钻具叶片使用性能和创新叶片设计理论,提出了基于儒可夫斯基保角变换法与经典水力翼型相结合的涡轮钻具叶片设计新方法,以?127涡轮钻具叶片为研究对象,运用搭建的涡轮钻具叶型参数化设计平台和自主设计的涡轮钻具性能测试台架,完成了5种翼型的造型设计,研究了5种叶片流场性能,开展了设计叶片的性能测试实验,对比分析了设计叶片与塔里木油田某型在役?127涡轮叶片的实际效能。实验及仿真结果表明,基于新方法设计的NACA-0012翼型加厚叶片在600 r/min转速及15 L/s流量的设计工况下,其单级扭矩达5.83 N·m,较相同条件下某在役?127涡轮的单级扭矩提高约6.4%,级效率提高约1.16%,整体性能有了实质提升。     

IBM PC集群计算机ATA磁盘系统升级技术方法研究

文章概述了IBMPC集群计算机的系统结构。对该系统在石油地震资料处理应用中存在的ATA磁盘系统故障率高的问题进行了分析，提出了针对刀片式服务器的ATA磁盘系统进行升级的解决方案。对石油地震资料处理高性能运算具有一定的参考价值。     

QS-R02反渗透阻垢分散剂工业应用试验

介绍QS-R02新型反渗透阻垢分散剂在齐鲁股份有限公司橡胶厂反渗透系统的工业试验情况,同QS-R01反渗透阻垢分散剂进行了对比。工业应用试验结果表明:新型QS-R02反渗透阻垢分散剂的碳酸钙临界饱和指数LSI达到2.5,阻垢分散效果明显优于QS-R01,能够实现橡胶厂反渗透系统运行过程不加酸的目的。同时,QS-R02药剂磷含量低,浓水总磷含量达到国家污水综合排放二级标准要求,无环境污染,具有良好的经济效益和社会效益。     

涡轮搅拌桨反应器混合过程的数值计算

利用CFD方法计算单层涡轮反应器搅拌槽内流体混合过程的速度场和浓度场,研究物料在搅拌槽内的混合过程,以及不同监测点对混合时间的影响。结果表明,搅拌槽内物料的混合主要受槽内流体的流动形式所影响;混合时间的长短与监测点位置有关;在搅拌桨的桨叶附近进行监测所得到的混合时间较短,在液面附近进行监测所得的混合时间较长。在实际生产和试验中,应注意对监测点位置的选取。