Reaction between the tetragonal tungsten bronze niobate K2Sr4Nb10O30 and the perovskite Pb(Mg1/3Nb2/3)O3

The search for dielectric materials with a high dielectric constant and ′_r = ƒ(T) curves with a flat profile fitting the X7R specification is still ongoing. Promising results were obtained by mixing compounds with closely related structures, such as the tetragonal tungsten bronze (TTB) niobate K₂Sr₄Nb₁₀O₃₀ and the perovskite Pb(Mg_1/3Nb_2/3)O₃ (PMN). The present study, based on three methods of synthesis, explores the origin of the spreading out of the dielectric curves ′_r = ƒ(T). For the composition 10x K_0.2Sr_0.4NbO₃ (KSN) + (1 − x)Pb(Mg_1/3Nb_2/3)O₃ (PMN) with x = 0.3–0.6, the three synthesis methods provided similar characteristics and for the highest perovskite ratio (x = 0.3), the ′_r = ƒ(T) curve exhibits a flat profile. When lithium is used as a sintering agent, ′_r = ƒ(T) curves present a linear dependency with the temperature. These materials are also characterized by a structural and a microstructural inhomogeneity. Two phases TTB and perovskite type, different from KSN and PMN, are present after calcination and sintering, but not evenly distributed. The PbO loss during sintering also contributes to the evolution of the properties of the material.     

影响凹印铜金粉印金光泽度的主要因素

在研究国内外铜金粉的微观形貌、厚度、水面遮盖率、定向排列、光泽度和粒度分布的基础上，分析了影响凹印铜金粉印金光泽度的主要因素。结果表明，国产铜金粉颗粒级差大、细小颗粒所占比例过多、金属片太厚、水面遮盖率小、定向排列不好等是影响国产铜金粉印金光泽度的主要因素。     

A new alloy design concept for austenitic stainless steel with tungsten modification for bipolar plate application in PEMFC

The feasibility of a new alloy design concept utilizing the principle of ‘tungsten bronze effect’ is critically evaluated for the development of metallic bipolar plates for proton exchange membrane fuel cell (PEMFC). An austenitic stainless steel (ASS) is modified with W and La to improve the stability of the passive film in an acidic environment as well as to reduce the contact resistance by the tungsten bronze effect. The experimental ASS containing W and La was evaluated in a simulated PEMFC environment of H₃PO₄ and H₂SO₄ solutions at 80 °C, and the electrical property was evaluated by performing a contact resistance test. The test results show that the ASS modified with W and La has good passive film stability for corrosion resistance and low contact resistance. The X-ray photoelectron spectroscopy (XPS) analysis clearly suggests the possibility of the tungsten bronze effect from the change in valency state of W⁶⁺ to W⁵⁺ in the passive film formed on the modified ASS. The feasibility of a new alloy design concept utilizing the ‘tungsten bronze effect’ is well demonstrated; however, more study is highly required for the development of metallic bipolar plates of PEMFC.     

Effect of heat treatment on microstructure and properties of hot-extruded nickel-aluminum bronze

The effect of heat treatment on the microstructure and properties of a hot-extruded nickel-aluminum bronze was investigated. Experimental materials were heat treated through different processes, including quenching, normalizing, aging and annealing, and their microstructure, corrosion resistance and mechanical properties were characterized. It is found that quenching causes all β phase transformed into β phase, however, normalizing causes β phase transformed into β α and κ phases. When the quenched sample is aged, fine phase is precipitated from the as-quenched microstructure of β＇ phase. Annealing causes the transformation of β into a and κ phases. The results of mechanical property tests show that quenching, normalizing and aging improve the tensile strength and hardness of the experimental material, with a corresponding fall in elongation. Annealing raises the elongation but reduces the tensile strength and hardness. Furthermore, corrosion resistance of nickel-aluminum bronze ranks from worse to better in the following order： aged, quenched, normalized, hot-extruded and annealed. However, with the exposure time of corrosion test increasing, the difference of average corrosion rate between those nickel-aluminum bronzes tums small.     

Influence of heat treatment on tribological behaviors of novel wrought aluminum bronze

1　ＩＮＴＲＯＤＵＣＴＩＯＮＡｌｕｍｉｎｕｍｂｒｏｎｚｅｐｏｓｓｅｓｓｅｓｅｘｃｅｌｌｅｎｔｐｈｙｓｉｃａｌ,ｍｅｃｈａｎｉｃａｌａｎｄｔｒｉｂｏｌｏｇｉｃａｌｐｒｏｐｅｒｔｉｅｓ .Ｉｔｉｓａｖａｉｌａｂｌｅｆｏｒｍａｋｉｎｇｗｅａｒ ｒｅｓｉｓｔｉｎｇａｎ     

利用广西气刀土原料研制高档卫生陶瓷

在对广西气刀土原料性能研究的基础上,进行了在卫生陶瓷坯料、釉料中的应用研究。坯料中加入4%～7%的广西气刀土原料替代等量的2#苏州土,在釉料中引入4～6%的气刀土原料替代1#苏州土,可以生产出理化性能和外观质量达到了美国ASMEA112.19.2M-1998标准要求的高档卫生陶瓷产品。引入广西气刀土原料使泥浆性能增强、厚化系数降低、湿坯硬度特别是内硬度明显提高、干坯抗折强度增大;制品体积密度增加、气孔率和吸水率降低;增强釉面乳浊效果、提高釉面白度,保证和提高产品的热稳定性能。     

Electrodeposition preparation of Nafion-Pt-HxMoO3 and its activity toward methanol oxidation

A composite catalyst Nafion-Pt-HxMoO3 was prepared on a glassy carbon by cyclic voltammetry methods in sulfuric acid solution containing Na2MoO4, H2PtCl6 and Naton, and its activity for the methanol oxidation was studied with Pt-HxMoO3 as comparison. It is found that the electrocatalytic activity and the stability of Pt-HxMoO3 are improved by the Nation. The activity of Pt-HxMoO3 reaches its maximum when the content of Nation in the preparation solution is 0.012%（mass fraction）. In this case the oxidation peak current of methanol on Nation-Pt-HxMoO3 is 1.76 times larger than that on Pt-HxMoO3 and keeps unchanged when the potential is set at 0.3 V （vs Hg-Hg2SO4） for 5 000 s in 1 mol/LCH3OH＋0.5 mol/L U2SO4 solution. The results from energy dispersive spectroscopy show that the content of Nation in the composite is 0.57%. The results from scanning electron spectroscopy show that the composite of Nafion-Pt-HxMoO has a gain size of about 90 nm and distributes more uniformly than Pt-HxMoO3.     

Tool wear mechanism in turning of novel wear-resisting aluminum bronze

1　ＩＮＴＲＯＤＵＣＴＩＯＮＡｌｕｍｉｎｕｍｂｒｏｎｚｅｉｓａｎｉｍｐｏｒｔａｎｔｅｎｇｉｎｅｅｒｉｎｇｍａｔｅｒｉ ａｌｄｕｅｔｏｉｔｓｅｘｃｅｌｌｅｎｔｐｈｙｓｉｃａｌ ,ｍｅｃｈａｎｉｃａｌ,ａｎｔｉ ｃｏｒｒｏ ｓｉｏｎａｎｄｗｅａｒｒｅｓｉｓｔｉｎｇｐｒｏｐｅｒｔｉｅｓ .Ｏｕｒｒｅｓｅａｒｃｈｇｒｏｕｐｄｅ ｖｅｌｏｐｅｄａｓｐｅｃｉａｌｔｙｐｅｏｆｈｉｇｈｓｔｒｅｎｇｔｈ ,ｗｅａｒ ｒｅｓｉｓｔｉｎｇａ ｌｕｍｉｎｕｍｂｒｏｎｚｅ(ＫＫ ) ,ｗｈｉｃｈｉｓｅｘｃｅｐｔｉｏｎａｌｌｙｇｏｏｄｆｏｒ…     

电弧喷涂铝青铜复合涂层的抗高温氧化作用与机理

采用铝青铜底层,外加厚度为0.1～0.2 mm的纯铝涂层可进一步地提高涂层体系的抗氧化性能.900 ℃加热12 h的10次循环氧化试验结果表明,纯铝层的应用有助于提高铝青铜涂层的自封孔能力,在涂层表面形成的增厚富铝氧化膜以及在涂层基体界面上形成的富铝氧化层都对钢铁基体的防护有利.复合涂层体系与试件基体结合可靠,没有早期失效迹象,是一种有希望的高温防护涂层体系.     

低锡青铜镀层电解退除工艺

介绍低锡青铜镀层电解退除工艺及应用情况,并对影响因素和退镀机理进行探讨。工艺成分简单,溶液稳定,使用寿命长,底层不易腐蚀,退镀溶液可直接加入镀液使用。