Study of metal assisted anisotropic chemical etching of silicon for high aspect ratio in crystalline silicon solar cells

Textured surface is commonly used to enhance the efficiency of silicon solar cells by reducing the overall reflectance and improving the light scattering. In this study, a comparison between isotropic and anisotropic etching methods was investigated. The deep funnel shaped structures with high aspect ratio are proposed for better light trapping with low reflectance in crystalline silicon solar cells. The anisotropic metal assisted chemical etching (MACE) was used to form the funnel shaped structures with various aspect ratios. The funnel shaped structures showed an average reflectance of 14.75% while it was 15.77% for the pillar shaped structures. The average reflectance was further reduced to 9.49% using deep funnel shaped structures with an aspect ratio of 1:1.18. The deep funnel shaped structures with high aspect ratios can be employed for high performance of crystalline silicon solar cells.     

Preparation and properties of nano-sized SnO2 powder

1　INTRODUCTIONSnO2isoneofthemainmaterialsusedingassensor.Becauseofthehumidityandgassensingfunction,itattractsmoreandmoreattentions.Butthepresentproblemishowtoimprovethestabilityandsensibilityofgassensor.Researchershavetakenmanymeasurestoresolvethisproble…     

Processing and microstructure of non-oxide ceramic fibres

Research and development efforts on high-temperature, oxidation-resistant fibres have increased over the past decade due to the demand for light-weight, stiff and strong composite materials in aerospace applications. Varieties of ‘high-performance’, continuous, non-oxide fibres with low-density, high tensile strength and tensile modulus have been developed either from organic precursors or via chemical vapour deposition for fabrication of ceramic matrix composites. Fibres derived from polymer precursors (e.g. Nicalon, Tyranno, HPZ) are small in diameter (compared to CVD monofilaments) and are ideally suited for ceramic composites. Processing, microstructural stability and mechanical properties of these newly developed SiC and Si₃N₄ base fibres are briefly reviewed in this paper.     

超细Fe3O4粒子表面包覆酞菁钴性质研究

本文研究了合成载氧体的金属有机化学液相淀积法制造工艺，所得产物经ＴＥＭ、ＸＰＳ、Ｍｏｓｓ－ｂａｕｅｒ谱和Ｂ－Ｈ仪等手段，研究了它的结构和磁性能。实验表明，酞青钴以薄层形式包覆在Ｆｅ＿３Ｏ＿４的表面，封闭了Ｆｅ＿３Ｏ＿４的表面孔洞，稳定了Ｆｅ＿３Ｏ＿４的物相，增强了磁性能。     

孤岛油田西区聚合物驱开发研究

孤岛油田西区注聚区1997年3月投入注聚后，高渗层得到有效封堵，吸水剖面得到明显改善。注聚期间，通过实施注聚区外围水井降水或停注、油井放大生产压差和调整注聚井注入速度等开发措施，扩大了聚合物波及体积，聚合物驱取得了明显效果。     

Application of annexation principle of thermodynamic property of In-Pb-Sb and In-Bi-Pb melts

Based on the principle of annexation and phase diagrams, the structural units of In-Pb-Sb and In-Bi-Pb melts were determined, and their calculating models of mass action concentrations were formulated. Calculated results agree well with practical values, which in turn show that the models deduced can reflect the structural realities of corresponding melts and the principle of annexation is applicable not only to some binary metallic melts, but also to ternary metallic melts.     

氧化铝生产过程结疤溶解的研究

针对氧化铝生产过程结疤现象。研制出一种新型清洗溶剂，溶垢率可达95%，清洗效果达到《工业设备化学清洗质量标准》要求。     

构造作用对油气生成和运聚的影响

有机质从埋藏开始，就处于极其复杂的地球物理化学场中，环境提的能量，一是热量，二是机械能，机械能，主要是通过机械力作用传递给系统的，另外还以机械波的形式赋予系统一定的机械能。当发生断褶构造运动时，机械力对油气运移的影响尤为突出，它经能量的迁移转化，促成了包括机械力降解和地应力驱动等一系列的连锁反应，制造了一次次高效的成油（生运）事件，本文以突变论为着眼点，按照改造控制建造的思路，大胆提出构造运动制造生排烃事件，成就含油气系统的假说。     

液压支柱表面镀层改进之探讨

通过比较电镀硬铬和化学镀镍在液压支柱表面处理上的应用 ,探讨了化学镀镍在配方、工艺、设备、镀层性能、环保等方面的优越性。     

隔震结构在省防震减灾中心大楼工程中的应用

结合工程实例介绍了隔震结构在工程设计中的应用