Analysis and proposition of limiting current density measurement protocol

Limiting current density at different temperatures, backpressures, and balance gases can be used to separate molecular diffusion resistance, Knudsen diffusion resistance and local transport resistance of membrane electrode assembly (MEA). However, the measurement of limiting current density has no unified protocol. The diverse choices in the literature, either in the control of current or voltage or in the atmosphere like relative humidity and O₂ concentrations, make it difficult to compare the results and identify the true bottleneck hindering the mass transport. In this work, the current-voltage curves obtained by current scanning/stepping and voltage scanning/stepping methods under dilute O₂ of different concentrations and a wide range of relative humidity were measured and analyzed systematically. It is found that the voltage stepping method is superior to the other three ways of control for the reliable determination of the limiting current density. Aided with simultaneous electrochemical impedance spectroscopy measurement, the limiting current density can be determined with pinpoint accuracy. When the limiting current density is just used to qualitatively evaluate different MEA, the voltage scanning method can be used instead for its high time efficiency. The selection of the atmosphere also plays an important role in suppressing the distortion from excessive water and reducing the spurious contribution from proton conduction resistance. It is found that O₂ concentrations at 0.5 vol% and relative humidity at 90% can give the best estimation of O₂ transport resistance in membrane electrode assembly.     

Microcrack healing in zirconia ceramics under a DC electric field/current

Flash event caused by a DC electric field/current was applied to the crack healing in 8 mol % Y₂O₃ stabilized cubic ZrO₂ polycrystals (8Y-CSZ). The flash event, which occurred by applying the DC power higher than a critical value of 100 mW/mm³, successfully healed the microcrack within several minutes without any healing agents at a furnace temperature of 800 °C. As compared to the healing treatment under static annealing, the healing phenomena were accelerated about 2 times under the flash treatment even at the same temperatures, suggesting that the enhanced healing phenomena cannot be explained only by the temperature effect. Since the rate of grain growth was accelerated under the flash treatment, the flash healing would be accelerated through the current-enhanced diffusional processes. This study shows for the first time that the flash event has a potential to apply to the crack healing process in the ceramic materials and composites.     

FeOOH–CoS composite catalyst with high catalytic performances for oxygen evolution reaction at high current density

Water electrolysis is an efficient approach for high-purity hydrogen production. However, the anodic sluggish oxygen evolution reaction (OER) always needs high overpotential and thus brings about superfluous electricity cost of water electrolysis. Therefore, exploiting highly efficient OER electrocatalysts with small overpotential especially at high current density will undoubtedly boost the development of industrial water electrolysis. Herein, we used a simple hydrothermal method to prepare a novel FeOOH–CoS nanocomposite on nickel foam (NF). The as-prepared FeOOH–CoS/NF catalyst displays an excellent OER performance with extremely low overpotentials of 306 and 329 mV at 500 and 1000 mA cm⁻² in 1.0 M KOH, respectively. In addition, the FeOOH–CoS/NF catalyst can maintain excellent catalytic stability for more than 50 h, and the OER catalytic activity shows almost no attenuation no matter after 1000 repeated CV cycles or 50 h of stability test. The high catalytic activity and stability have exceeded most non-noble metal electrocatalysts reported in literature, which makes the FeOOH–CoS/NF composite catalyst have promising applications in the industrial water electrolysis.     

Influence of anode current density on carbon parasitic reactions during electrolysis

In the electro-deoxidation process, carbon parasitic reaction (CO₃^2- + 4e^-=C + 3O^2-) usually occurs when using carbon materials as the anode, which leads to increase of the carbon content in the final metal and decrease of the current efficiency of the process. The aim of this work is to reduce the negative effect of carbon parasitic reaction on the electrolysis process by adjusting anode current density. The results indicate that lower graphite anode area can achieve higher current density, which is helpful to increase the nucleation site of CO₂ bubbles. Most of CO₂ would be released from the anode instead of dissolution in the molten CaCl₂ and reacting with O^2- to form CO₃^2-, thus decreasing the carbon parasitic reaction of the process. Furthermore, the results of the compared experiments show that when the anode area decreases from 172.78 to 4.99 cm², CO₂ concentration in the released gases increases significantly, the carbon mass content in the final metal product decreased from 1.09% to 0.13%, and the current efficiency increased from 6.65% to 36.50%. This study determined a suitable anode current density range for reducing carbon parasitic reaction and provides a valuable reference for the selection of the anode in the electrolysis process.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

近10年我国传统饮料酒白酒和黄酒品质安全研究现状与展望

总体上说,我国白酒和黄酒的安全性指标研究起步较晚,特别是白酒和黄酒中氨基甲酸乙酯(ethyl carbamate, EC)的研究,大部分研究更多关注检测方法的开发,针对可能超过限量的指标的消减技术研究较少,而从源头和过程控制角度进行消减的技术研究显得更为稀少。建议尽快制订相关标准和/或控制指南,加大基础性研究和控制技术研究力度,为我国白酒和黄酒品质安全研究提出建设性建议。本文重点回顾了近10年来我国传统饮料酒白酒、黄酒中氨基甲酸乙酯、氰化物、生物胺、真菌毒素和塑化剂等安全风险因子的研究现状,包括检测方法、产品现状、过程变化、产生机制或形成途径,以及消减技术,对现有饮料酒白酒和黄酒品质安全研究的问题与挑战进行了分析。     

上海市火力发电行业能源计量现状分析

能源计量与节能监测、能源审计、能源统计、能源利用状况分析是用能单位能源管理和节能工作的基础。通过对本市部分火力发电企业的现场调研，针对性地提出改进建议，以期帮助用能单位增强能源计量在节能减排工作中的有效性。     

Experimental investigations of enhanced glow based on a pulsed hollow-cathode discharge

In this work, the pulsed hollow cathode discharges at low pressure argon with an axial magnetic field were studied. The results indicate that the pulsed discharge is operated in an enhanced glow(EG) mode. Under the same conditions, the discharge current of the pulsed discharge is two or three orders higher than that of the direct current discharge. The spatial and temporal evolution of the light emission shows that, the current fluctuation at the rising edge of the pulse plays an important role for the EG discharge of pulsed hollow cathode, which forms a high-density, highcurrent and long-distance plasma column outside the cavity.     

基于STM32的开环霍尔电流传感器的温度补偿研究

研究了一种基于软件补偿结合恒流源补偿的改进温度补偿方法,应用单片机、恒流源、数字温度传感器、乘法器等硬件电路,对传统软件补偿进行了优化,补偿效果较传统恒流源补偿有了明显提升,“温漂”整体下降了约13.7%。在传统的温度补偿方法如热敏元件补偿、恒流源补偿、软件补偿等方式上做了补充,对于霍尔电流传感器精度的提升及实际生产需求的满足有重要意义。