Novel energy-saving window coating based on F doped TiO2 nanocrystals with enhanced NIR shielding performance

To reduce the energy consumption of cooling in the hot summer days, searching for novel NIR shielding materials for buildings is of great value. In this report, monodispersed F doped TiO₂ nanocrystals with an average size of 8.6 nm were synthesized as novel solar shielding materials for energy-saving windows. All the products adopted an anatase TiO₂ structure. After doping of F ions, the morphology of TiO₂ was transformed from an irregular shape to a pseudospherical shape. The Raman shift and XPS depth analysis confirmed the successful doping of F⁻ ions into the lattice oxygen sites in the TiO₂ structure. The introduction of F⁻ ions generated free electrons and bulk Ti³⁺ in TiO₂ crystals, which activated a localized surface plasmon resonance (LSPR) absorption in the NIR region. Correspondingly, the NIR shielding performance of the TiO₂ films improved with increasing F doping amounts. The NIR shielding value of the films increased from 1.3% to 43.2% when the molar ratio of F to Ti increased from 0 to 0.3. The reason can be attributed to the enhanced NIR absorption induced by the increased electron concentration after doping of fluorine ions. The F–TiO₂ films showed superior visible transmittance (90.1–96.7%). Moreover, the F–TiO₂ films lowered the indoor temperature of the heat box by 5.3 °C in the thermal tests. Overall, the prepared F–TiO₂ nanocrystals show a great potential to be used for energy-saving windows.     

Synergistic effect of bulk phase doping and layered-spinel structure formation on improving electrochemical performance of Li-Rich cathode material

In this study, La was doped into the lithium layer of Li-rich cathode material and formed a layered-spinel hetero-structure. The morphology, crystal structure, element valence and kinetics of lithium ion migration were studied by field emission scanning electron microscope (FESEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). The La doped lithium-rich cathode material exhibited similar initial discharge capacity of 262.8 mAh g^?1 at 0.1 C compared with the undoped material, but the discharge capacity retention rate can be obviously improved to 90% after 50 cycles at 1.0 C. Besides that, much better rate capability and Li⁺ diffusion coefficient were observed. The results revealed that La doping not only stabilized the material structure and reduced the Li/Ni mixing degree, but also induced the generation of spinel phase to provide three-dimensional diffusion channels for lithium ion migration. Moreover, the porous structure of the doped samples also contributed to the remarkable excellent electrochemical performance. All of these factors combined to significantly improve the electrochemical performance of the material.     

Enhanced electrochemical performance of LiNi0.8Co0.1Mn0.1O2 via titanium and boron co-doping

Titanium and boron are simultaneously introduced into LiNi_0.8Co_0.1Mn_0.1O₂ to improve the structural stability and electrochemical performance of the material. X-ray diffraction studies reveal that Ti⁴⁺ ion replaces Li⁺ ion and reduces the cation mixing; B³⁺ ion enters the tetrahedron of the transition metal layers and enlarges the distance of the [LiO₆] layers. The co-doped sample has spherical secondary particles with elongated and enlarged primary particles, in which Ti and B elements distribute uniformly. Electrochemical studies reveal the co-doped sample has improved rate performance (183.1 mAh·g^-1 at 1 C and 155.5 mAh·g^-1 at 10 C) and cycle stability (capacity retention of 94.7% after 100 cycles at 1 C). EIS and CV disclose that Ti and B co-doping reduces charge transfer impedance and suppresses phase change of LiNi_0.8Co_0.1Mn_0.1O_2.     

Surface modification of superfine SiC powders by ternary modifiers-KH560/sodium humate/SDS and its mechanism

SiC is a promising functional ceramic material with many great properties. High concentrated SiC slurry with excellent rheology and stability is required in some processes of ceramic forming. In this work, the dispersion of SiC powders was obviously improved by ternary modifiers: γ-(2,3-epoxypropoxy) propytrimethoxysilane (KH560), sodium humate and sodium dodecyl sulfate (SDS). Modified SiC slurry showed the lowest viscosity of 0.168 Pa s at a solid content of 50 vol%. The maximum absolute value of zeta potential of SiC increased from 47.3 to 61.6 mV by modification. Sedimentation experiments showed that a highly stable suspension of modified SiC was obtained at pH 10. SiC green body with high density of 2.643 g/cm³ was prepared with modified powders by slip casting. X-ray photoelectron spectra (XPS) and thermogravimetry (TG) measurements indicated the adsorption of modifiers on SiC surface. Therefore, modified SiC powders could stably disperse in aqueous media due to the increase of electrosteric repulsion between particles. The novel strategy used in this study could further improve the dispersion of SiC powders.     

Surface modification of cellulose nanocrystals towards new materials development

Cellulose nanocrystals (CNCs) are a kind of sustainable nanoparticle from biomass, which are widely used as reinforcing filler and assembly building block for high-performance composites and function materials including biomaterial, optics, and so forth. Here, their unique advantages in material applications were reviewed based on their rod-like morphology, crystalline structure, dimension-related effects, and multi-level order structure. Then, we focused on the molecular engineering of CNCs, including the structure and physicochemical properties of their surface, along with surface modification methods and steric effects. We further discussed the performance-improvement and functionalization methods based on multi-component complex systems, together with the effects of surface molecular engineering on the performance and functions. Meanwhile, methods of optimizing orientation in uniaxial arrays were discussed along with those of enhancing photoluminescence efficiency via surface chemical modification and substance coordination. In the end, we prospected the design, development, and construction methods of new CNCs materials.     

Stabilization and superconductivity of AlB2-type nonstoichiometric molybdenum diboride by Sc doping

Molybdenum diboride is unique among transition metal diborides because it exists in both hexagonal (AlB₂-type) and rhombohedral structures. However, it is difficult to stabilize the superconducting AlB₂-type phase, which requires either extreme synthesis condition or suitable chemical doping. Here we report the structural and physical properties of Sc-doped nonstoichiometric molybdenum diborides (Mo_0.95Sc_0.05)_1-xB₂ and (Mo_1-ySc_y)_0.71B₂ prepared by the common arc melting method. The AlB₂-type phase is found to form over wide ranges of 0 ≤ x ≤ 0.29 and 0.025 ≤ y ≤ 0.30 for the first time, and bulk superconductivity with T_c up to 7.9 K is observed. T_c increases with increasing x in the (Mo_0.95Sc_0.05)_1-xB₂ series, but evolves nonmonotonically with varying y in the (Mo_1-ySc_y)_0.71B₂ series. Despite this contrast, T_c of both borides follows nearly the same linear dependence on the electron-phonon coupling constant, suggesting that it is mainly controlled by the electron-phonon interaction. In addition, the stabilization of AlB₂-type structure is attributed to the decrease in the number of d electrons as a consequence of Sc doping, which suggests that a similar effect may be achieved by substituting Mo with other d electron-poorer metal elements.     

Nitrogen-doped hierarchically porous carbon obtained via single step method for high performance supercapacitors

In the present work, nitrogen doped hierarchically activated porous carbon (APC) samples have been synthesized via single step scalable method using ethylene di-amine tetra acetic acid (EDTA) as precursor and KOH as activating agent. Activated porous carbons with different pore sizes have been developed by varying the activation temperature. SEM, TEM and SAXS analysis suggest that with variation of activation temperature, a hierarchical porous structure with interconnected meso-pore and micro pores has been achieved. The sufficiently high surface area of the synthesized materials provides active sites to enhance the diffusion of ions between the electrolyte and the carbon electrodes. The electrode prepared at 800 °C activated sample exhibited highest specific capacitance of 274 Fg^-1 in two electrode setup, at a current density of 0.1 Ag^-1 in 1 M aqueous H₂SO₄. Along with this, it showed maximum energy density of 9.5 Whkg^?1 at a power density of 64.5 Wkg^-1. The remarkable electrochemical performance reveals that the synthesized nitrogen doped activated carbon electrodes derived from EDTA can be tuned to have optimum pore structure and pore size distribution for better electrochemical performance, so it can be considered as a potential electrode material for applications in electrochemical energy storage.     

High performance H2 sensor based on rGO-wrapped SnO2–Pd porous hollow spheres

Hydrogen (H₂) sensors based on metal oxide semiconductors (MOS) are promising for many applications such as a rocket propellant, industrial gas and the safety of storage. However, poor selectivity at low analyte concentrations, and independent response on high humidity limit the practical applications. Herein, we designed rGO-wrapped SnO₂–Pd porous hollow spheres composite (SnO₂–Pd@rGO) for high performance H₂ sensor. The porous hollow structure was from the carbon sphere template. The rGO wrapping was via self-assembly of GO on SnO₂-based spheres with subsequent thermal reduction in H₂ ambient. This sensor exhibited excellently selective H₂ sensing performances at 390 °C, linear response over a broad concentration range (0.1–1000 ppm) with recovery time of only 3 s, a high response of ～8 to 0.1 ppm H₂ in a minute, and acceptable stability under high humidity conditions (e. g. 80%). The calculated detection limit of 16.5 ppb opened up the possibility of trace H₂ monitoring. Furthermore, this sensor demonstrated certain response to H₂ at the minimum concentration of 50 ppm at 130 °C. These performances mainly benefited from the special hollow porous structure with abundant heterojunctions, the catalysis of the doped-PdO_x, the relative hydrophobic surface from rGO, and the deoxygenation after H₂ reduction.     

Enhancement of super-hydrophilic/underwater super-oleophobic performance of ceramic membrane with TiO2 nanowire array prepared via low temperature oxidation

A gradient porous ceramic membrane with surface super-hydrophilic and underwater super-oleophobic performance was prepared by combining hydrogel directional freezing method and low temperature oxidation process. The effects of solid contents and sintering temperature on the ceramic membrane matrix were examined. The reaction time and synthesis temperature on the TiO₂ nanowire array were also evaluated. In addition, the related effects on pore size distribution, permeation flux, contact angle, and oil-in-water emulsion separation were systematically investigated. The ceramic membrane matrix pore size changed from 0.5 μm to 25 μm gradually, indicating the gradient structure controlled by the growth of ice. The super-hydrophilic and underwater super-oleophobic performance of ceramic membrane surface was obtained with surface modification by TiO₂ nanowire array, and the surface water contact angle and underwater oil contact angle were less than 5° and over 158°, respectively. The bonding strength between TiO₂ nanowire and ceramic membrane matrix was high enough to withstand ultrasonic waves. The ceramic membrane modified with TiO₂ nanowire array was used for 1000 ppm diesel oil-in-water emulsion separation, and the stable separation efficiency and flux were about 97% and 100–200 L/(m² h bar) even after 10 filtration cycles.