脉冲电镀最佳参数之探索和优化

本文利用正交实验法对脉冲电镀各控制参数进行试验,对影响分散能力、镀层可靠性及外观质量的各种因素进行探讨,寻找影响外观质量的显著因子并加以控制,同时进一步优化脉冲电镀的工艺参数。     

换热器表面预处理及防腐工艺

石化换热器许多设备都由碳钢制作,需要涂镀渗防腐,为保证防腐层质量,需要进行严格的表面预处理。概述了机械与化学表面预处理及相关的防腐工艺。     

Monodisperse polymer/metal composite particles by electroless chemical deposition: Effect of surface functionality of polymer particles

Micron‐sized polymer particles were coated with layers of nickel compounds by plating electrolessly in the presence of aqueous solutions of nickel chloride, sodium hypophosphite, sodium citrate, and ammonium chloride at elevated temperature. The uniform functional polymer particle could be obtained by seeded polymerization. To investigate the effect of surface functionality on the conditions for nickel deposition, the polymer particle was functionalized with the thiol group. From morphological observation, it was found that the mode of nickel deposition was greatly dependent on the surface functionality of the polymer particle. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 420–424, 2003     

酸性镀锡液的新进展

从近几年美国发明专利的角度扼要综述酸性镀锡液的新进展。说明酸性镀锡液由氟硼酸盐型发展为烷基磺酸盐型的改进过程。列出参考文献９篇。     

非金属电镀用导电漆的研制

介绍了导电漆、作为导电填料的片状镀银铜粉的制备工艺流程。分别研究了漆膜表面单位电阻与镀银铜粉的含量及其粒径以及钛酸酯偶联剂的含量之间的关系。结果表明,当镀银铜粉的粒径为400目、质量分数在57%~65%之间,钛酸酯偶联剂的质量分数为10%时,所得涂膜的导电性能最佳。加入含C-18的油酸可以使导电漆长期贮存而电阻值不变。经检测,所得涂膜具有良好的性能:附着力1级,硬度1 H,柔韧性1 mm,冲击强度50 kg/cm2,膜厚10~15μm,漆膜表面每厘米电阻0.15Ω,每分米电阻0.47Ω。指出了导电漆应用过程中的注意事项。     

高速钢表面PN＋PVD复合处理工艺和性能研究

采用多弧离子镀设备,在高速钢W18Cr4V上先进行等离子氮化,再沉积TiN薄膜,研究了不同渗氮温度和时间对PN＋TiN薄膜组织和性能的影响。结果表明,温度为500℃左右和时间为2h以上条件下对W18Cr4V进行渗氮处理后再沉积TiN薄膜,可以得到最佳的薄膜表面显微硬度（1800～2000HV0.05）和膜／基结合力（50N）,涂层耐磨性也得到明显提高。     

30CrMnSiNi2A钢件镀硬铬的氢脆分析

本文叙述了用延迟破坏法试验超高强度钢(υb=1700MPa)不超过三次镀硬铬的氢脆情况。     

A novel electroless silver depositing method for magnesium alloys

Depositing silver on magnesium alloy by both electroless plating and organic coatings was studied. The organic coating was made by immersing samples in organosilicon heat-resisting varnish. In this method the organic coating acts as interlayer between the substrate and silver film. When the reaction starts, silver deposits directly on the interlayer. X-ray diffraction and SEM analysis were used to determine the composition and morphology of the interlayer and silver film. The potentiodynamic polarization curves for corrosion studies of coated magnesium alloys were performed in a corrosive environment of 3.5% NaCl（mass fraction） at neutral pH （6.9）. The results indicate that compared with the substrate, the corrosion resistance of coated magnesium alloys increases greatly. Moreover, the method proposed in this work is environmentally friendly, non-toxic chemicals were used. In addition, it provides a new concept for the corrosion inhibition of magnesium alloys.     

Effects of gold plating on the resistance to high temperature discoloration of the cavity for ceramic packages

The effects of thickness and types of gold plating on the resistance to high temperature discoloration of gold plating on cavity surface of ceramic package were investigated. It was found that the thicker gold plating, the less discoloration degree for ceramic packages. Non-cyanide gold plating performed better resistance to high-temperature aging than cyanide gold plating. The relationship between the gold plating thickness and the amount of diffused Ni to the gold plating of ceramic packages with Au/Ni and Au/Ni-Co platings after heating at 420℃for 15 min was also studied. When the gold plating thickness reach 2.0 μm and 1.6 μm for Au/Ni and Au/Ni-Co plating systems, respectively, no discoloration was observed on the gold plating surface of cavity, and the corresponding diffused Ni amounts (mass fraction) are 1.0% and 0.4%, while the diffused Co to the gold plating is 0.04%.     

Electroless deposition of Ni on template of halloysite and its magnetic property

Halloysite template, a ceramic substrate, is of a hollow cylindric structure, on which the fine Pd nanoparticles are uniformly formed by the reduction of palldate chloride to initiate electroless deposition. The electroless deposition of Ni is catalyzed by the Pd particles, which results in a uniform layer of Ni-P alloy on halloysite. The alloy is of a nanocrystalline structure, of which the average diameter is about 6 nm. After being heat-treated at 400 ℃, it contains both Ni and Ni12P5 crystal, meanwhile, the Ni crystal gets larger with an average size of 51.9 nm.The content of phosphorous in the Ni layer has a great influence on crystal structure. The metallized halloysite has a higher inherent coercive force, and a much lower saturation magnetization in its as-plated state, while after heattreatment, the inherent coercive force decreases drastically. These magnetic properties have great relationship with the superparamagnetism of Ni nanocrystalline and the stress anisotropy in Ni layer.