Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.     

Influence of Polyalkylmethacrylate VII on Boundary Film Formation,Friction,Wear and Efficiency of Lubricants

1 Influence of PAMAon Boundary Fil mFormation and Friction1.1 Experi mental methodsUltra-thin optical interferometry has been used tostudy thinlubricating fil ms for more than a decade and theexperi mental details of this technique have been reportedpreviously[1].The principle of the test setup is shown inFigure1.A polished steel ball is loaded and rolled againstthe flat surface of a glass disc that is coated with a thinsemi-reflecting chromiumlayer and a silica spacer of about500nmthickne…     

双级染料激光放大器泵浦能量分配的数值研究

用染料激光放大器的横向稳态泵浦理论，对不同的入射光能量选择不同的增益计算方法，研究了双级染料放大器的泵浦能量分配比例、泵浦光总能量和信号光能量大小对激光增益的影响。计算结果表明，对于其他参数确定的放大系统，存在着最佳的泵浦能量分配比例，可获得最大增益输出。通过自编程序的计算，可方便地找出特定系统泵浦能量分配比例的最佳值。     

Mechanical spectroscopy in commercial Fe–6 wt.% Si alloys between 400 and 1000 K

Mechanical spectroscopy, neutron diffraction and differential scanning calorimetry (DSC) were performed on commercial Fe–6 wt.% Si alloy after quenching from high temperature. The damping spectrum shows a peak at around 800 K and an associated modulus defect. The modulus shows an increase during the second and subsequent heating runs. In addition, an anomaly in the modulus behavior has been found at around 400 K. Different thermal treatments allows to obtain two different recovery degrees of the quenched-in defects. The influence of the recovery degree on the 800 K internal friction peak and on the anelastic modulus has been evaluated and confirm the validity of the grain boundary mechanism associated to this peak. Experimental results are discussed on the basis of recovery and ordering processes.     

Cs-K混合蒸气中Cs(8D)+K(4S)碰撞能量转移

在Cs-K混合蒸气中，两步激发Cs原子到8D态，观察了Cs(8D) K(4S)→Cs(5D) K(4P)碰撞能量合并逆过程(REP，reverse energy pooling)。应用双调制技术探测K(4P)原子发射的荧光，基态K原子密度用光学吸收方法测量。得到了REP速率系数，讨论了其它过程对速率系数的影响．     

Voltage sag compensation with minimum energy injection by use of a micro‐SMES

This paper presents a method to compensate voltage sags with minimum energy injection for a series‐connected voltage restorer using a micro‐SMES. A circuit for extracting the fundamental symmetrical components from sag voltages and a minimum energy injection algorithm is described. Simulations of voltage sag compensation have been carried out using PSCAD/EMTDC for various faults. The simulation results confirm the validity of the proposed method and show the possibility of reducing the size of energy storage devices. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(3): 70–80, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10047     

深穿透复合射孔技术在中原油田的应用

深穿透复合射孔是一项把射孔与高能气体压裂两种技术有机地结合在一起的综合改造油气层的新技术。重点对它的技术原理，包括设计原理、枪身内火药燃烧气体对射孔孔眼的冲刷作用原理、火药燃烧气体射流的高能气体压裂作用原理等进行了研究与探讨，同时对它的施工工艺、现场应用等方面进行了阐述，经中原油田189口井现场应用证明，其工艺简便，成本低廉，可实现多层跨隔层使用，处理后增产效果显著，投入产出比高，可代替传统的聚能射孔技术，具有广阔的推广和应用价值。     

Modelling the impact of energy taxation

Energy taxation in Sweden is complicated and strongly guides and governs district energy production. Consequently, there is a need for methods for accurate calculation and analysis of effects that different energy tax schemes may have on district energy utilities. Here, a practicable method to analyse influence of such governmental policy measures is demonstrated. The Swedish Government has for some years now been working on a reform of energy taxation, and during this process, several interest groups have expressed their own proposals for improving and developing the system of energy taxation. Together with the present system of taxation, four new alternatives, including the proposed directive of the European Commission, are outlined in the paper. In a case study, an analysis is made of how the different tax alternatives may influence the choice of profitable investments and use of energy carriers in a medium‐sized district‐heating utility. The calculations are made with a linear‐programming model framework. By calculating suitable types and sizes of new investments, if any, and the operation of existing and potential plants, total energy costs are minimized. Results of the analysis include the most profitable investments, which fuel should be used, roughly when during a year plants should be in operation, and at what output. In most scenarios, the most profitable measure is to invest in a waste incineration plant. However, a crucial assumption is, with reference to the new Swedish waste disposal act, a significant income from incinerating refuse. Without this income, different tax schemes result in different technical solutions being most profitable. An investment in cogeneration seems possible in only one scenario. It is also found that particular features of some alternatives seem to oppose both main governmental policy goals, and intentions of the district heating company. Copyright © 2002 John Wiley & Sons, Ltd.     

联产供冷与电力供冷能耗比较分析

文中将两种供冷能耗比较分解成用电煤耗差、用热煤耗量、增加产汽用电煤耗量三部分进行分析，按照热量法得出在目前一般情况下联产供冷比电力供冷通常费能和定性定量结论，为全面研究比较热电冷联产与分产的能耗奠定一个基础。     

MB8镁合金薄板的搅拌摩擦焊

针对我国航空航天工业常用的MB8镁合金。采用搅拌摩擦焊工艺进行焊接，对其焊缝的成形特点、组织特征和力学性能进行分析。结果表明，采用搅拌摩擦焊焊接镁合金效果良好。