Electrochemical growth and characterization of iron doped cadmium sulfide thin films

Cadmium Sulfide and Ferrous doped Cadmium Sulfide thin films have been prepared on different substrates using an electrodeposition technique. Linear sweep voltammetric analysis has been carried out to determine deposition potential of the prepared films. X-ray diffraction analysis showed that the prepared films possess polycrystalline nature with hexagonal structure. Surface morphology and film composition have been analyzed using Scanning electron microscopy and Energy dispersive analysis by X-rays. Optical absorption analysis showed that the prepared films are found to exhibit Band gap value in the range between 2.3, 2.8 eV for Cadmium Sulfide and Ferrous doped Cadmium Sulfide.     

Measurement and Identification of the Parameters of SPICE-Models of a Bipolar Transistor

A method of measuring and identifying the static parameters of a bipolar transistor is considered. The characteristic of the transistor, from which the parameters of the model are determined, is chosen depending on what group the calculated parameters belong to. The characteristics are measured in such a way that the equations of the model describing them can be reduced to the simplest form.     

基于模式理论光栅椭偏参数反演的数值模拟

将一种广泛用于求解系统优化问题的方法——正单纯形法，求解光栅的椭偏方程。首先，利用求解光栅的傅立叶模式理论对TE和TM波的复反射系数进行求解。然后计算出其相应的椭偏参数(△，Ψ)，并在该值的基础上加入不同偏差的随机高斯噪声，将加入噪声后的值(△m，Ψm)作为模拟测量值。最后使用优化算法进行反演。通过对几种常用面形光栅椭偏参数的数值模拟，一方面表明傅立叶模式理论计算光栅的椭偏参数不仅精度高。而且速度快；另一方面表明利用正单纯形法得到的光栅参数值很接近于正演时假设的参数值，从而从理论上证明了利用椭偏法测量光栅各种光学参数的可行性。     

钻井参数仪的模块化设计方法研究

文章以模块化设计原理为基础，讨论了钻井参数仪的模块划分，模块化设计准则和主要设计内容。采用模块化设计方法、现场设备网络的开放网络和现场总线解决方案设计的钻井参数仪，具有传输信号稳定、可靠性高、抑制噪声能力强、组建现场网络成本低等特点。     

带参数的一阶脉冲微分方程边值问题

利用上下解和单调迭代法。讨论了带参数的一阶脉冲微分方程。获得了单边Lipschitz条件下这类方程边值问题的解的存在性。     

Texture Changes During the Ripening of Port Salut Argentino Cheese in 2 Sampling Zones

ABSTRACT: Texture changes during ripening of Port Salut Argentino cheese for different sampling zones were studied. Compression relaxation tests were performed and results were analyzed using both Maxwellian and Peleg's models. Elastic equilibrium modulus obtained from the Maxwellian model decreased from 1.22 to 0.11 10⁴Pa during ripening. The constants derived from Peleg's model, k₁ and k₂, diminished with ripening time from 1.18 to 0.71 min and from 1.27 to 1.12, respectively. Asymptotic equilibrium modulus from Peleg's model decreased from 0.95 to 0.07 10⁴Pa during ripening. Rate parameters derived from a 1st order kinetics applied to both equilibrium moduli showed that the decrease was faster in the external zone (0.0846 d⁻¹) than in the central zone (0.0368 d⁻¹). The correlation between equilibrium moduli, salt concentration, moisture content, and maturation indexes was obtained with a determination coefficient of 0.76.     

直接氯化法合成对硝基氯化苄

介绍了以对硝基甲苯和氯气为原料 ,在催化剂存在下合成对硝基氯化苄的方法 ,考察了催化剂种类、反应温度、溶剂配比等因素对反应的影响 ,优化的反应条件为 :对硝基甲苯用量 1 3 7g,对硝基甲苯 /邻二氯苯 (摩尔比 ) =1∶ 0 .6,w (偶氮二异丁腈 ) =0 .6% ,反应时间 3 h,反应温度 1 60℃ ,产物单程收率大于 65 % ;将反应混合物中未反应的原料分离后 ,以无水乙醇为溶剂结晶纯化 ,物料 /溶剂 (摩尔比 ) =1∶ 1 .5时晶体含量在 99.0 %以上 ,结晶收率达 67     

Addition of pectolytic enzymes: an enological practice which improves the chromaticity and stability of red wines

Summary The effect of the addition of four commercial pectolytic preparations on the visual characteristics (colour and turbidity) of red wines has been evaluated. The effect of both clarifying and colour extracting enzymes and the effect of different doses used, were evaluated and compared. All the red wines treated enzymatically, independent of the type of enzyme and dose, present chromatic characteristics which can be considered better than those of the control wines. Also, those wines treated with enzymes had greater stability during 2 years storage in bottles, in particular the turbidity was better than untreated wines.     

A procedure to prepare cross-sectional samples for TEM

Cross-sectional transmission electron microscopy (XTEM) is an imaging technique particularly suited to the study of layered structures. For integrated electronic devices it has become a common practice to use XTEM to assess the shape and crystallinity of component layers as well as defect structures introduced by processing. A procedure for preparing samples to be viewed by XTEM is described.