轻质滤料滤池的试验与研究

轻质滤料滤池是以比水密度略小的滤料为滤床的滤池，通过以净水厂的原水和污水处理厂的二级处理出水为过滤试验对象，所取得的结果表明：下向流轻质滤料滤池对浊度和悬浮固体（SS）的去除率分别可以达到80％和45％，而滤床的水头损失不超过15cm。因此轻质滤料滤池可以以预过滤的形式配置在过滤处理的净水和污水的处理工艺中。     

Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.     

吐丝圈径对大规格高碳盘条组织性能的影响

计算与分析了斯太尔摩冷线上盘条的吐丝圈径、搭接密度及"佳灵"装置横向布风曲线之间的关系,研究了吐丝圈径的大小对大规格82B盘条组织和性能的影响,确定了大规格82B盘条最小吐丝圈径应为980mm.     

Selectivity Enhancement to the Exclusive Formation of Ethyltoluenes and Hydrogen During Dehydroalkylation of Toluene with Ethane

The dehydroalkylation of toluene with ethane to the isomeric ethyltoluenes was studied on 0.4Pt/H-ZSM-5 at varying contact times (1/WHSV). At a high contact time of 1.0 h, toluene disproportionation and hydrogenolysis reactions dominate, resulting in low selectivity to the desired ethyltoluenes via the alkylation reaction. However, at a low contact time of 0.12 h side reactions are eliminated, resulting in maximum selectivities to the kinetically favored ethyltoluenes and hydrogen. Results at high selectivities to ethyltoluenes provide significant insight into reaction pathways.     

Catalytic oxidation of naphthalene using a Pt/Al2O3 catalyst

Polycylic aromatic hydrocarbons (PAHs) are listed as carcinogenic and mutagenic priority pollutants, belonging to the environmental endocrine disrupters. Most PAHs in the environment stem from the atmospheric deposition and diesel emission. Consequently, the elimination of PAHs in the off-gases is one of the priority and emerging challenges. Catalytic oxidation has been widely used in the destruction of organic compounds due to its high efficiency (or conversion of reactants), its economic benefits and good applicability.

This study investigates the application of the catalytic oxidation using Pt/γ-Al₂O₃ catalysts to decompose PAHs and taking naphthalene (the simplest and least toxic PAH) as a target compound. It studies the relationships between conversion, operating parameters and relevant factors such as treatment temperatures, catalyst sizes and space velocities. Also, a related reaction kinetic expression is proposed to provide a simplified expression of the relevant kinetic parameters.

The results indicate that the Pt/γ-Al₂O₃ catalyst used accelerates the reaction rate of the decomposition of naphthalene and decreases the reaction temperature. A high conversion (over 95%) can be achieved at a moderate reaction temperature of 480 K and space velocity below 35,000 h⁻¹. Non-catalytic (thermal) oxidation achieves the same conversion at a temperature beyond 1000 K. The results also indicate that Rideal–Eley mechanism and Arrhenius equation can be reasonably applied to describe the data by using the pseudo-first-order reaction kinetic equation with activation energy of 149.97 kJ/mol and frequency factor equal to 3.26 × 10¹⁷ s⁻¹.     

Thermal stability of reinforced Nb3Sn composite superconductor under cryocooled conditions

Several types of reinforced Nb₃Sn wires have been developed to prevent reduction of superconducting properties by applying a strong electromagnetic force. To fabricate a cryocooled magnet using those reinforced wires, we experimentally measured the minimum quench energy (MQE) under cryocooled conditions of some reinforced Nb₃Sn wires. As a result, it became clear that thermal stability expressed as MQE was controlled by the temperature margin between the temperature of the operating condition and the transition temperature from superconductivity to normal. Using the FEM analysis, it was realized that the cause of the decline in thermal stability for the reinforced wires was the low thermal conductivity of the reinforced materials.     

SLIMLINE+K型多功能撬装双滚筒试井绞车简介

SLIMLINE K型多功能撬装双滚筒试井绞车为整体式结构，多用于海上平台，可进行电子压力计和机械压力计试井，以及井下工具的投放、震击、打捞等完井作业。该试井绞车采用先进的数控技术，使起下纲丝／电缆实现自动化控制，该系统能够对斜井、定向井进行随钻测试。     

高炉煤气净化系统新技术研究与应用

济钢第二炼铁厂针对原高炉煤气净化系统处理能力不足等问题，研制了新的煤气净化系统。该系统采用单根文氏管、串联花环、丝网脱水器湿法除尘，取代原串联文氏管电除尘净化工艺。应用表明，新系统运行安全，净煤气含尘量小于10^mg／m^3，含水量小于5g／m^3，高炉风温提高90℃。     

气流式加速度传感器的敏感机理

介绍了在研制气流式加速度传感器过程中，为对气流式加速度传感器进行建模，作者对气流式加速度传感器的工作机理进行了理论性探讨。在分析过程中以流体力学、传热学和惯性理论为基础并结合实验结果，建立了适合于气流式加速度传感器的气体运动方程和能量方程。同时还讨论了热线测量加速度的方法及根据实验分析了输入加速度对腔体内温度及传感器输出电压的影响，从而为进一步研究一系列气流式传感器的工作机理提供了方法。     

聚合物复合材料填充剂的改性

在前人研究的基础之上，归纳总结了聚合物复合材料填充剂的种类，综述了对其进行表面改性的目的、条件、方法、工艺以及对改性结果的表征等。文章还分析了影响填充聚合物复合材料性能的因素，指出了今后发展的方向。