成分配比对稀土钨电极材料组织及力学性能影响

通过固液掺杂、等静压压制、中频烧结的方法，制备了不同的氧化镧、氧化钇、氧化锆三元掺杂成分比例的钨电极材料烧结棒材，探究了不同成分配比对样品显微组织、第二相粒子分布以及宏观力学性能的影响。结果表明，氧化镧、氧化钇、氧化锆三元复合添加能够有效改善第二相粒子在钨基体中的分布形态，降低第二相在晶界的过度富集，提高钨电极材料的综合力学性能。并且当添加成分镧、钇、锆质量比为3:1:1时，材料具有最好的综合力学性能，致密度可达96.04%，显微硬度可达549.37HV0.3，抗压强度可达3785MPa，原因是此配比下第二相粒子最为细小均匀，弥散程度最高，对基体晶粒的细化作用最好，该配比下钨基体平均晶粒尺寸达到10.3μm。     

离子型稀土矿山淋洗及尾水富集试验研究

对浸矿后离子型稀土原地浸矿场采用清水进行淋洗，在184天的清水淋洗过程中，尾水氨氮值从最开始的507mg/L，降低至140mg/L，淋洗尾水pH4.52~3.10。淋洗尾水采用两级反渗透膜分离，既回收有价资源稀土，又能使出水氨氮达标。结果表明，产水氨氮浓度稳定低于15mg/L，对稀土的截留率高于98.25%，浓水中稀土离子平均浓度313.4mg/L，可进一步回收稀土资源。     

稀土石膏常压酸化法制备硫酸钙晶须的研究

以含稀土的石膏为原料运用常压酸化法合成硫酸钙晶须,探讨了不同工艺条件对生成的硫酸钙晶须形貌的影响,同时还考察了晶型助长剂的种类和晶型助长剂的含量对硫酸钙晶须生长的影响,利用SEM和XRD分别对硫酸钙晶须的表面形貌、物相特征做了表征分析。实验得到制备硫酸钙晶须的最佳的反应条件：稀土石膏质量浓度为0.22 g/mL、反应时间为25 min、盐酸浓度为2.8 mol/L、反应温度为70 ℃、陈化时间为4 h,在此条件下合成的硫酸钙晶须平均长度为61 μm,平均长径比为30.5;通过对比实验选出了CuCl₂作为促进硫酸钙晶须生长的助长剂,在添加5%（质量分数）的CuCl₂的情况下可使硫酸钙晶须长径比从30.5增至41,长度从61 μm增至81 μm。     

Electrocatalytic activity of LaSr3Fe3O10 and LaSr3Fe3O10-GO towards oxygen reduction reaction in alkaline medium

Oxygen reduction reaction(ORR) plays a critical role in many energy conversion and storage processes.Therein, a comparative study of the electrocatalytic activity for ORR in 0.1 mol/L KOH solution was conducted using layered perovskite-like LaSr_3 Fe_3 O_(10) and LaSr3 Fe_3 O_(10)-graphene oxide(GO) composite as electrodes. Linear sweep voltammetry(LSV) results show that the LaSr3 Fe_3 O_(10)-GO hybrid exhibits higher current density, a more positive onset potential(-0.15 V vs. Hg/HgO) in comparison with LaSr_3 Fe_3 O_(10).The value of the overall transferred electrons for both catalysts implies a dominant two electron process for ORR. Both catalysts under alkalic conditions exhibit a two-step Tafel slope, suggesting a change in the reaction mechanism for ORR. The composite electrode exhibits a higher ORR current density, but inferior durability performances in relative to the LaSr_3 Fe_3 O_(10) electrode.     

Effect of spatial constraints on the phase evolution of YFeO3-based nanopowders under heat treatment of glycine-nitrate combustion products

Formation and structural transformations of yttrium orthoferrite crystals have been studied using X-ray diffractometry, Mössbauer spectroscopy and transmission electron microscopy combined with electron microdiffraction. Said processes have been studied under heat treatment of glycine-nitrate combustion products. There have been identified formations of three structural yttrium orthoferrite modifications – amorphized hexagonal <h₁>-YFeO₃ (P6₃cm) and nanocrystalline hexagonal h₂-YFeO₃ (P6₃/mmc), as well as nanocrystalline orthorhombic o-YFeO₃ (Pbnm), which are selectively formed depending on available three-dimensional confinements. Based on the analysis of changes in the fluid and size composition formulation, it has been proposed mechanism for formation and transformation of YFeO₃ nanocrystals, including growth stage of h₂-YFeO₃ crystals due to amorphized phase of <h₁>-YFeO₃ up to critical size of about 15?nm and their subsequent transformation into orthorhombic form o-YFeO₃.     

岩矿稀有金属化学分析技术浅析

分析当前较为常用的岩矿稀有元素分析技术方法,并对几种常见的稀有元素分析方法进行了阐述,希望为我国矿产勘探领域提供一些有价值的参考借鉴。     

钛基Ce掺杂SnO_2-RuO_2电极的制备及其对焦化废水的电解处理

采用溶胶-凝胶法制备了经稀土元素Ce掺杂改性的Ti/RuO_2-SnO_2-Ce电极,利用SEM、XRD、EDS等分析方法对电极表面的形貌、物相和涂层成分进行了表征,利用CV曲线、LSV曲线等检测手段对电极的电化学性能进行了测试。以Ti/RuO_2-SnO_2-Ce电极为阳极,钛板为阴极,构建电化学氧化反应装置,并采用其对焦化废水进行电解处理。结果表明,Ti/RuO_2-SnO_2电极经稀土Ce改性后极板表面活性位点数量明显增大,金属涂层的结晶化程度明显增强,电极的催化氧化活性显著提高。室温条件下,保持pH值为7.83,在电流密度为30mA/cm~2,电解时间为30min时,焦化废水经电解处理后COD去除率可达91.63%,TOC去除率可达66.22%,UV254值下降到0.921。     

Heavy rare earths,permanent magnets,and renewable energies: An imminent crisis

This article sounds the alarm that a significant build-out of efficient lighting and renewable energy technologies may be endangered by shortages of rare earths and rare earth permanent magnets. At the moment, China is the predominant supplier of both and its recent rare earth industrial policies combined with its own growing demand for rare earths have caused widespread concern. To diversify supplies, new mining—outside of China—is needed. But what many observers of the “rare earth problem” overlook is that China also dominates in (1) the processing of rare earths, particularly the less abundant heavy rare earths, and (2) the supply chains for permanent magnets. Heavy rare earths and permanent magnets are critical for many renewable energy technologies, and it will require decades to develop new non-Chinese deposits, processing capacity, and supply chains. This article clarifies several misconceptions, evaluates frequently proposed solutions, and urges policy makers outside of China to undertake measures to avert a crisis, such as greater support for research and development and for the cultivation of intellectual capital.     

Sol-Gel Preparation and Luminescence Properties of BaMgAl10O17∶Eu2+ Phosphors

The synthesis of BaMgAl10O17∶ Eu2 (BAM) phosphors using the sol-gel method and their luminescence properties were reported. The blue-light emitting BAM was synthesized using citric acid and ethylene glycol as chelating materials. Emission of blue-light was obtained from these phosphors. The luminescent intensity increases as the temperature of heat treatment is increased. This study investigated the effects of the molar ratio of ethylene glycol to citric acid (Φ value), with respect to the phase formation and luminescence properties of BAM. The variation of the Φ value resulted in the change of the sol-gel reaction mechanism and the microstructures of the resultant powders. An increase in Φ value leads to an increase in the rate of BAM phase formation. The photoluminescent intensity of the prepared phosphors increases with heating temperatures because of enhanced crystallization.     

Effects of Rare Earths on Toughness of 31Mn2SiRE Wear-Resistance Cast Steel

The toughness of 31Mn2SiRE wear-resistance cast steel were increased by means of RE compound modification and high temperature austenitizing. The results show that the microstructures can be refined, needle and network ferrite are eliminated, the dislocation density and the quantity of dislocated martensite are increased remarkably, and the shape and distribution of inclusions are improved by the addition of RE. Therefore, the mechanical properties of the modified steel can be greatly increased, especially the toughness (αK) by 44%, yield strength (σs) by 10%, and elongation (δ5) by 42%.