辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响

研究辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响。采用3种不同上辊/下辊转速比(ω/ω0,ω为上辊转速,ω0为下辊转速)1:1、1:1.2及1:1.4进行多次试验。结果显示,在最大辊速差条件下(ω/ω0=1:1.4),7075铝板在轧制方向的屈服强度和极限抗拉强度分别提高41.5%和21.9%。此外,当辊速比ω/ω0为1:1.4时,成品轧制板的平均晶粒尺寸减小36%,横剖面平均硬度增加约9.2%。织构研究结果显示,辊速差越大,成品各向同性及硬度越大。然而,采用不同辊速度的连铸连轧会导致变形板伸长率降低约6%。     

基于滚动摩擦作用下玉米颗粒在模拟筒仓卸料中的力链分析（网络首发、推荐阅读）

针对颗粒滚动摩擦作用对筒仓中玉米颗粒的力链空间分布进行研究，通过EDEM离散元软件建立筒仓模型与仿真玉米颗粒模型进行卸粮仿真模拟，并与筒仓卸料实验作流态对比，验证模型与仿真结果的准确性。通过对模拟仓进行切片观察和数据处理，对比分析了不同摩擦情况下力链的细观参数随时间演化规律。模拟结果表明：颗粒间摩擦系数越大，卸粮完成的最终时间越长；颗粒间滚动摩擦系数越小，颗粒由整体流转变为管状流的时间越早。对于有漏斗的筒仓来说，减小颗粒间摩擦会改变整体流和管状流之间的极限，从而增加产生管状流的面积。标准滚动摩擦系数下玉米颗粒在卸料过程中会出现起拱-塌陷效应；减小滚动摩擦，玉米颗粒卸料较稳定，未出现起拱的应力突增、以及拱塌陷的应力衰减；增大颗粒间滚动摩擦不但会增加拱效应，且出现成拱高度距离漏斗口更高。     

Effect of spheroidized microstructure on the impact toughness and electrochemical performance of a high-carbon steel

The influence of cementite spheroidization on the impact toughness and electrochemical properties of a high-carbon steel has been thoroughly investigated in this study. Heavy warm rolling, followed by 2 h of annealing, has resulted in near-complete spheroidization, leading to a microstructure consisting of nano-cementite globules dispersed in the ultrafine-grained ferritic matrix. The Charpy impact test exhibited superior impact toughness with increased spheroidization. It is validated by the presence of abundant dimples in the fractographs of spheroidized specimens, in contrast to the as-received one that experienced a brittle failure due to its lamellar pearlitic structure. Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) carried out in a 3.5% NaCl solution revealed that the corrosion resistance of the alloy gets improved with the increase in the degree of spheroidization. This is attributed to the lower susceptibility of the spheroidized specimen to microgalvanic corrosion owing to the minimum area of contact between nano-spheroidized cementite and ferrite, as elucidated with the help of EIS results aided by equivalent electrical circuit model.     

伊蒙粘土/炭黑/天然橡胶复合材料的性能研究

采用伊蒙粘土替代部分炭黑,研究伊蒙粘土用量对伊蒙粘土/炭黑/天然橡胶复合材料硫化特性、物理性能、动态力学性能和导热性能的影响。结果表明:随着伊蒙粘土用量增大,混炼胶的Payne效应减弱,最大转矩减小,正硫化时间缩短;硫化胶的耐热老化性能、气密性、抗冲击性能提高;添加5和7份伊蒙粘土的硫化胶物理性能和耐磨性能与未添加伊蒙粘土的硫化胶相当,且明显好于添加10和15份伊蒙粘土的硫化胶;伊蒙粘土可明显提高硫化胶的抗湿滑性能、减小滚动阻力。     

A Smart Deep Convolutional Neural Network for Real-Time Surface Inspection

A proper detection and classification of defects in steel sheets in real time have become a requirement for manufacturing these products, largely used in many industrial sectors. However, computers used in the production line of small to medium size companies, in general, lack performance to attend real-time inspection with high processing demands. In this paper, a smart deep convolutional neural network for using in real-time surface inspection of steel rolling sheets is proposed. The architecture is based on the state-of-the-art SqueezeNet approach, which was originally developed for usage with autonomous vehicles. The main features of the proposed model are: small size and low computational burden. The model is 10 to 20 times smaller when compared to other networks designed for the same task, and more than 700 times smaller than general networks. Also, the number of floating-point operations for a prediction is about 50 times lower than the ones used for similar tasks. Despite its small size, the proposed model achieved near-perfect accuracy on a public dataset of 1800 images of six types of steel rolling defects.     

基于改进耦合增强随机共振的滚动轴承故障诊断

针对强背景噪声下经典随机共振方法对滚动轴承故障特征提取效果差的问题,提出了一种基于改进耦合增强随机共振的滚动轴承故障诊断方法。首先,利用一个定参双稳系统和一个变参双稳系统构成耦合随机共振系统,外部输入直接作用于定参双稳系统;然后,通过调节变参双稳系统参数和耦合系数实现耦合系统的随机共振控制,并借助遗传算法实现控制参数的自适应选取。实验和工程应用验证了所提方法的有效性和优越性。     

微量Zr对不对称轧制Al-0.8Mg-0.9Si合金板织构及性能的影响

本文研究了微量Zr对不对称轧制Al-0.8Mg-0.9Si合金板及其相继固溶处理后的微观结构及性能的影响。结果表明：微量Zr在Al-0.8Mg-0.9Si合金中形成Al3Zr相弥散分布在基体中,在不对称轧制过程中,该化合物相对Copper{112}<111>、Brass{011}<211>、S{123}<634>、E{111}<110>和F{111}<112>等形变织构无明显影响；在随后的固溶处理过程中,轧制板材发生的再结晶使得Copper、Brass、S等形变织构的取向密度降低,但不溶的细小Al3Zr相在一定程度上抑制了不连续再结晶行为,反而使轧制过程中形成的E、F剪切织构的取向密度增加。添加微量Zr所形成的上述结构使该合金板材在固溶后获得较好的综合性能,其抗拉强度、屈强比和延伸率分别可达230MPa、0.49和9.5%以上；塑性应变比r值从0.7提高至0.84,杯突值IE由8.94提高至9.84,各向异性度|Δr|由0.15降低至0.04。     

控轧控冷中碳非调质钢的高周疲劳性能

 采用中碳非调质钢制造的轴类等零件常承受交变载荷，因而对钢材疲劳性能具有高的要求。为了评估控轧控冷工艺生产的非调质钢棒材的疲劳性能，利用旋转弯曲疲劳试验机研究了一种常用的钒微合金化中碳非调质钢38MnVS及对比钢38MnS的高周疲劳性能。结果表明，与38MnS钢相比，38MnVS钢中铁素体体积分数增加，组织明显细化；相分析表明约有54%的钒处于M（C，N）相中，且尺寸小于10 nm的M（C，N）粒子质量分数为32%，这些细小粒子的析出强化增量约为116 MPa。38MnVS钢的疲劳极限较38MnS钢提高了62 MPa，提高幅度约为18%；疲劳极限比从38MnS钢的0.43提高到38MnVS钢的0.48。M（C，N）相的析出强化及组织细化是38MnVS钢较38MnS钢具有优异疲劳性能的主要原因，但其疲劳性能仍低于锻态非调质钢。根据试验结果及文献数据，给出了预测铁素体＋珠光体型非调质钢疲劳极限的简便方法。