超临界机组发生FAC的因素及相互关系分析

为了减轻因流动加速腐蚀(FAC)引起的锅炉结垢加速、汽水系统管道厚度减小甚至爆裂现象，对超临界机组发生流动加速腐蚀的机理及其主要影响因素进行了研究，并讨论了管壁内表面粗糙度、蒸汽含汽率、pH值、溶氧量对FAC的影响，以及温度与pH值、温度与流速、pH值与溶解氧量、溶解氧量与氢电导率等影响因素之间的相互作用关系，最后结合实际电厂的运行数据验证了分析结果。研究表明：减小工质流速、管壁粗糙度和氢电导率，增大给水的pH值和溶解氧含量可以使FAC的腐蚀速率减小，超临界加氧处理时pH值应在8.9～9.2之间，溶解氧量范围为45～100μg/L,氢电导率的期望值在0.1μS/cm以下。由于各影响因素之间的作用十分复杂，本文只给出了大致范围和趋势，并未给出准确数据。     

Understanding δ-Bi2O3 fluorite degradation mechanism and related solutions for promising applications in distributed multigeneration

Oxygen selective membrane on the base of cermet δ-Bi₂O₃/Ag with an interpenetrating structure has the maximum potential efficiency of air separation. However, the degradation processes, including the phase degradation of fluorite δ-Bi₂O₃, do not make it possible to create a membrane with the required perfection and durability. In this work, the ordering of oxygen vacancies with the transformation of fluorite into the rhombohedral phase (S.G. R-3) was studied by powder HT XRD in situ at 600 °C on dense Bi_0.78Er_0.2Hf_0.02O_1.51 ceramics. Fast regeneration of disordered fluorite occurs at T = 640–700 °C. The phase degradation of fluorite due to the segregation of dopants at the second stage leads into stable phases - sillenite, tetragonal or rhombohedral phase (S.G. R-3m), depending on the composition of δ-Bi₂O₃. Fast regeneration of fluorite occurs when heated to 820 °C, which is unacceptable for membranes. Analysis of all available data allows us to propose approaches to optimize the composition of δ-Bi₂O₃ and technical solutions for creating durable oxygen selective membranes with promising use in distributed multigeneration. As a result of the analysis, a new solid electrolyte with better parameters was obtained.     

断控岩溶主控的缝洞型碳酸盐岩内部溶蚀相带表征——以塔河油田10区奥陶系油藏为例

以塔河油田10区的典型井组为研究对象，在明确断裂主控岩溶的背景下，分析岩溶作用过程与缝洞空间分布的关系，揭示了研究区缝洞体内幕结构及油气生产差异机理。通过对钻井、地震、示踪剂等动态和静态资料的分析，将研究区缝洞储集体划分为洞穴型、孔洞型、裂缝-孔洞型和裂缝型4种类型。结合地球物理描述与相似露头观察，分析断控岩溶作用下溶洞的发育过程，并建立基于成因演化的缝洞空间分布模式。岩溶作用下储层的发育具有分带性，依据该模式从内向外划分出4个溶蚀相带，分别是大型溶洞带、溶蚀孔洞密集区、缝洞联合发育体以及最外围的裂缝破裂带。不同的溶蚀相带其发育的主要储集体类型、储集物性、井震特征以及储量和产能情况有较大差异。在此基础上，结合生产动态资料所揭示的不同井之间的响应和连通情况，明确了研究区不同钻井分别钻遇了不同发育程度或演化阶段的缝洞溶蚀相带，且主要存在溶洞连通、缝洞连通和裂缝连通3种沟通方式。通过对缝洞溶蚀相带空间配置关系的有效刻画，采用确定性建模方法建立岩溶储层三维地质模型，并取得较好的数值模拟效果。     

退火工艺对激光选区熔化成形Ti6Al4V合金组织及室温力学性能的影响

以Ti6Al4V球形粉末为原料,利用激光选区熔化成形方法制备了Ti6Al4V合金试样,采用光学显微镜、扫描电镜及力学性能测试等手段,研究了退火工艺对Ti6Al4V合金室温力学性能及组织的影响规律。结果表明: SLM成形沉积态Ti6Al4V合金室温抗拉强度超过1200 MPa,而平均断后伸长率仅为4.0%;在650 ℃下进行真空退火处理,合金的抗拉强度仍保持在1200 MPa左右,规定塑性延伸强度R_p0.2高于1150 MPa,但试样的断后伸长率<10%;而在750及800 ℃下进行真空退火处理,合金试样的抗拉强度降至1100 MPa左右,规定塑性延伸强度高于1050 MPa,伸长率达到甚至超过10%,材料的综合强韧性得到明显提升。随着真空退火加热温度和保温时间的增加,SLM成形Ti6Al4V合金原始β晶界逐渐变模糊,晶粒趋向于等轴化。与此同时,快速冷却转变的α′针状马氏体未出现明显地粗化。     

基于PEMS测量的SSCR系统整车道路排放测试研究

基于车载排放测试系统进行SSCR系统国Ⅴ重型柴油车实际道路排放测试研究。SSCR后处理系统使用前后整车NO_x排放特征的比较显示:对比原NO_x排放,在市区工况下,SSCR系统可降低61.3%的NO_x排放,在高速工况下可以降低85.3%的NO_x排放。测试研究表明:安装有SS-CR系统的国Ⅴ重型柴油车在实际道路工况下NO_x排放符合国ⅤPEMS标准(送审稿)。     

Solid dispersion adsorbate technique for improved dissolution and flow properties of lurasidone hydrochloride: characterization using 32 factorial design

The aim of the present study was to improve the dissolution and flow properties of lurasidone hydrochloride (LH) by solid dispersion adsorbate (SDA) technique. Solid dispersions (SDs) of LH were prepared by fusion method using Poloxamer P188. The melt dispersion was adsorbed onto the porous carrier Florite (calcium silicate). A 3² factorial design was employed to quantify the effect of two independent variables, namely ratio of carrier (Poloxamer 188) and LH in SD and ratio of adsorbent (Florite) to SD. SDA granules of LH were studied for flow properties and characterized using differential scanning calorimetry, scanning electron microscopy, and X-ray diffraction. Tablets of optimized composition of SDA granules (equivalent to 20?mg of drug) and plain tablets were prepared by direct compression method. The dissolution studies were carried out in Mcllvaine buffer (pH 3.8) as per USFDA guidelines and characterized for parameters such as percent dissolution efficiency, t₅₀, and Q₃₀. Tablets prepared from SDA granules showed almost four-fold increase in cumulative percentage drug release as compared to tablets prepared from plain LH. The value of dissolution efficiency was enhanced from 49.60% for plain tablets to 94.15% for SDA tablets. SDA granules did not show any change in drug release and X-ray diffraction pattern after storage at 40?°C/75% of RH for 3?months, which confirms that Florite prevented conversion of drug from amorphous form to crystalline form improving physical stability of the amorphous state of LH.     

Ti改性催化裂化汽油选择加氢催化剂的研究

以氢氧化铝干胶和偏钛酸为主要原料制备了Al2O3-TiO2载体，采用等体积浸渍法制备出一系列不同TiO2含量及不同配体改性的CoMo/Al2O3-TiO2催化剂；采用BET，XRD，TPR，HRTEM等方法对所制备的催化剂进行了表征，在10 mL固定床评价装置上对所制备的两个系列催化剂进行了FCC汽油选择加氢脱硫活性评价。结果表明，载体中TiO2的质量分数为10%、浸渍液中添加乙二醇和磷酸改性的催化剂具有较高的加氢脱硫活性和选择性。     

Formulation strategy towards minimizing viscosity mediated negative food effect on disintegration and dissolution of immediate release tablets

Food induced viscosity can delay disintegration and subsequent release of API from solid dosage form which may lead to severe reduction in the bioavailability of BCS type III compounds. Formulations of such tablets need to be optimized in view of this postprandial viscosity factor. In this study, three super disintegrants, croscarmellose sodium (CCS), cross-linked polyvinylpolypyrrolidone (CPD), and sodium starch glycolate (SSG) were assessed for their efficiency under simulated fed state. Tablets containing these disintegrants were compressed at 10 and 30?KN, while taking lactose as a soluble filler. In addition to other compendial tests, disintegration force of these formulations was measured by texture analysis. Comparison of parameters derived from force – time curves revealed a direct relation of maximum disintegration force (F_max) and disintegration force development rate (DFDR) with compressional force in fasted state, whereas an inverse relationship of F_max and DFDR with compressional force was observed in fed state. The gelling tendency of disintegrants influenced the rate of release of API in simulated fed and fasted states when compressional force was changed. These observations recommend the evaluation of formulations in simulated fed state, in the development stage, with an objective of minimizing the negative impact of food induced viscosity on disintegration. Use of disintegrants that act without gelling or can counteract the effect of gelling is recommended for tablet formulations with reduced disintegration time (DT) and mean dissolution time (MDT) in fed state, respectively.     

选区激光熔化316L不锈钢的各向组织与性能

对采用选区激光熔化(SLM)制备的316L不锈钢增材制造试样进行了横向、纵向力学性能与微观组织分析。结果表明,增材制造SLM试件亚结构组织由尺寸为0.4 μm左右的胞状组织所构成,组织之间无明显的成分偏析,纵向与横向拉伸强度分别达到808和713 MPa,在经过1050 ℃热处理后,原组织中部分胞状组织消失,纵向及横向强度分别下降到673 MPa及579 MPa,增材制造试样相对传统热轧试样(550 MPa)具有明显的强度优势。SLM试样组织中存在未熔合缺陷,缺陷几何形状的方向性对其在拉应力作用下连接成裂纹有显著影响。热处理后缺陷长度方向与拉伸应力平行的纵向试样伸长率达到47.5%,横向试样伸长率为20%,伸长率指标均显著低于热轧316L钢试样,未熔合缺陷是导致3D打印试件塑性指标降低的主要因素之一。     

Plasmonic Oxygen-Deficient TiO2-x Nanocrystals for Dual-Band Electrochromic Smart Windows with Efficient Energy Recycling

Dual-band electrochromic smart windows capable of the spectrally selective modulation of visible (VIS) light and near-infrared (NIR) can regulate solar light and solar heat transmittance to reduce the building energy consumption. The development of these windows is however limited by the number of available dual-band electrochromic materials. Here, plasmonic oxygen-deficient TiO_2-x nanocrystals (NCs) are discovered to be an effective single-component dual-band electrochromic material, and that oxygen-vacancy creation is more effective than aliovalent substitutional doping to introduce dual-band properties to TiO₂ NCs. Oxygen vacancies not only confer good near-infrared (NIR)-selective modulation, but also improve the Li⁺ diffusion in the TiO_2-x host, circumventing the disadvantage of aliovalent substitutional doping with ion diffusion. Consequently optimized TiO_2-x NC films are able to modulate the NIR and visible light transmittance independently and effectively in three distinct modes with high optical modulation (95.5% at 633 nm and 90.5% at 1200 nm), fast switching speed, high bistability, and long cycle life. An impressive dual-band electrochromic performance is also demonstrated in prototype devices. The use of TiO_2-x NCs enables the assembled windows to recycle a large fraction of energy consumed in the coloration process (“energy recycling”) to reduce the energy consumption in a round-trip electrochromic operation.