美国固体照明技术进展概况

介绍了美国能源部于2002年开始实施的固体照明(SSL)技术的"下一代照明计划".同时对美国SSL技术的研发、生产和使用现状以及召开学术会议的情况做了叙述.     

实体造型中的几何约束

实体造型是一个基于约束的过程，完成从功能约束到几何约束、再到代数约束的转化而得到实体模型。本文讨论了几何约束的层次性及其表示，并且对几何约束同设计意图的关系进行了研究，提出了基于ＣＳＧ／ＧＣＧ／Ｂ－ｒｅｐ的模型表示。     

纳米级BaAl_2O_4微粉的制备和性质

分别用溶胶 -凝胶法、低温固相反应法 ,制得了纳米级BaAl2 O4微粉 ,用电镜观察了其形貌和粒径的大小 ,用X-射线衍射仪进行了物相分析 ,测定了其纯度与晶型 ,讨论了制备方法与粒度大小的相互影响     

MB8镁合金薄板的搅拌摩擦焊

针对我国航空航天工业常用的MB8镁合金。采用搅拌摩擦焊工艺进行焊接，对其焊缝的成形特点、组织特征和力学性能进行分析。结果表明，采用搅拌摩擦焊焊接镁合金效果良好。     

Acoustic emission method for research and control of friction pairs

One of the new physical methods that provides much information about the processes going on in a friction contact zone in real time is acoustic emission (AE). Basic experimental results of AE in friction are presented and analysed. Using AE signals we can get an indication about the state of the friction processes, about the quality of solid and liquid layers on the contacting surfaces in real time, sometimes about intensity of wear, changing of wear and friction regimes and so on. The influence of sliding velocity, load, roughness and some physical and mechanical properties of the body on the parameters of AE are also given. Some attention to the practical implementation of these techniques for control of capability for work of friction pairs in real conditions are given. Modern methods and devices enable condition monitoring of sliding and rolling bearings.     

锂离子电池有机电解液成膜添加剂的研究现状

文章综述了锂离子电池有机电解液成膜添加剂的作用原理，具体介绍了CO2、SO2、VC化合物、卤化物、有机铜盐以及马来酐等添加剂的研究现状。     

Exit effect on hydrodynamics of the internal circulating fluidized bed riser

This is the first time an extensive investigation has been carried out regarding the effects of riser exit geometry on pressure drop and solid behaviour inside the Internal Circulating Fluidized Bed (ICFB) riser, using different riser exit geometries at several operating conditions.The Radioactive Particle-Tracking (RPT) technique was used for solid concentration measurements and solid residence time distribution at the exit zone. Experiments were conducted using Geldart B particles, in the gas superficial velocity range of 4 to 10 m/s. Axial solid hold-up, solid residence time distribution in the exit zone, and the reflux ratio factor k_m, (defined earlier by [E.H. Van der Meer, R.B. Thorpe, J.F. Davidson, Flow patterns in the square cross-section riser of a circulating fluidized bed and the effect of riser exit design, Chem. Eng. Sc. 55 (19) (2000) 4079-4099]), were the main criteria used to investigate the impact of gas-solid separator devices implemented at the ICFB riser exit.Solid residence time distribution results and axial solid hold-up profiles provided clear evidence that the separator device at the riser exit strongly influences the hydrodynamic structure of the ICFB riser. The V-shaped riser exit geometry was found to be the optimum of all the configurations studied.     

Hydrogen production in solid electrolyte membrane reactors (SEMRs)

In the present work, the prospects and trends of solid electrolyte membrane reactors (SEMRs) towards hydrogen production, are discussed. Initially, an overview of the principles, the properties and the techniques related to the usage of the SEMRs, are presented. In the following, a literature survey covering earlier and recent developments of the various methods (e.g. reforming or partial oxidation or dehydrogenation of hydrocarbons, steam electrolysis) employed in the SEMRs for the production of hydrogen, is performed. Finally, the current status of this research field is analyzed and future research topics are proposed.     

Impact of the addition of an enzyme pool on an activated sludge system treating dairy wastewater under fat shock loads

BACKGROUND: The application of lipase‐rich enzyme pools (such as the crude solid enzymatic preparation (SEP) obtained from Penicillium restrictum solid‐state fermentation of agro‐industrial wastes) to activated sludge systems may be an effective strategy for preventing various operational problems. The continuous addition of SEP to the treatment system can become cost‐prohibitive when in situ production and/or storage are factored in. The application of SEP to high‐fat wastewater treatment would only be justified as an emergency measure, such as a sudden increase in the fat content of the bioreactor influent. Therefore, the primary objective of this work was to investigate the efficiency of a crude SEP during fat shock loads, simulated through the periodic addition of dairy industry waste containing high fat concentrations to the feed stock of an activated sludge system, operated in continuous mode. RESULTS: The test bioreactor exhibited a higher average chemical oxygen demand (COD) removal efficiency than the control bioreactor (83% for control and 90% for test) and the fat accumulation in the biological flocs of the test bioreactor was 3.2 times lower than that in the control bioreactor. Turbidity was also lower in the effluent of the test bioreactor (123 and 66 FTU in control and test, respectively) and it had a shorter recovery time between shock loads, especially when the interval between loads was shorter than one month (biweekly and weekly shock loads). CONCLUSION: The addition of SEP during fat overloads in the reactor feed maintained efficient COD removal in the test bioreactor for 270 days without any operational problems. Copyright © 2008 Society of Chemical Industry