Fabrication of different conductive matrix supported binary metal oxides for supercapacitors applications

Here, we have fabricated the spinel binary-metal oxide (FeCo₂O₄) via a solvent-free and cost-effective approach. The nanocomposites of the as-fabricated binary-metal spinel oxide have been prepared with three different conductive-matrices, namely r-GO, CNTs, and PANI, via ultra-sonication approach. The spinel phase and surface functionalities of the fabricated FeCo₂O₄ sample have been confirmed via XRD and FT-IR analyses, respectively. The morphological-structure and elemental composition of the fabricated samples have been probed via FESEM and EDX results. The role of added conductive-matrices in the improvement of the electrical conductivities of the fabricated nanocomposites has been investigated via I–V experiments. The electrochemical experiments, conducted in half-cell configuration, showed that FeCo₂O₄/PANI nanocomposite exhibited the highest specific capacitance (658.9 Fg^-1) than that of the remaining two nanocomposites. Furthermore, FeCo₂O₄/PANI nanocomposite exhibited excellent cyclic stability as it lost just 8.3% of its initial specific capacitance even after 3000 cyclic tests. The superior capacitive-activity of the FeCo₂O₄/PANI nanocomposite is accredited to its high conductivity, large surface area, and synergy effects between the pseudocapacitance derived from the PANI and FeCo₂O₄ nanostructure. The electrochemical and electrical measurements suggested that FeCo₂O₄/PANI nanostructure is an emerging contender for energy storage applications.     

Sputtered Fe1·5CoNi0.5 coating: An improved protective coating for SOFC interconnect applications

In an attempt to optimize the properties of FeCoNi coating for planar solid oxide fuel cell (SOFC) interconnect application, the coating composition is modified by increasing the ratio of Fe/Ni. An Fe_1·5CoNi_0.5 (Fe:Co:Ni = 1.5:1:0.5, atomic ratio) metallic coating is fabricated on SUS 430 stainless steel by magnetron sputtering, followed by oxidation in air at 800°C. The Fe_1·5CoNi_0.5 coating is thermally converted to (Fe,Co,Ni)₃O₄ and (Fe,Co,Mn,Ni)₃O₄ without (Ni,Co)O particles. After oxidation for 1680 h, no further migration of Cr is detected in the thermally converted coating region. A low oxidation rate of 5.9 × 10^?14 g² cm^?4 s^?1 and area specific resistance of 12.64 mΩ·cm² is obtained for Fe_1·5CoNi_0.5 coated steels.     

Tailoring surface capacitance of Ti3C2Tx-PANI@CNTs nanoarchitecture for tunable energy storage and high-performance micro-supercapacitor

Transition metal carbide or nitride (MXenes), as a novel family of two-dimensional materials, exhibit huge potential for electrochemical energy storage thanks to their excellent electrical conductivity, fast ion diffusion rate, high electrochemical activity and good hydrophilicity. However, the electrochemical properties of MXenes tend to be deteriorated due to the self-restacking phenomenon. Herein, by self-assembly, a unique three-dimensional (3D) Ti₃C₂T_x-PANI@CNTs (TPCs) nanoarchitecture was constructed. Through optimizing structures, the surface capacitance of TPCs can be tailored to tune energy storage. The optimal specific capacitance up to 431.9 F/g was achieved under 1 A/g. Further, the TPCs nanoarchitectures were prepared into self-standing films with excellent mechanical properties and micro-supercapacitors (MSCs) in various shapes were manufactured based on the film. The MSCs demonstrate competitive energy storage capacities, obtaining an areal capacitance of 78.2 mF/cm² and energy density of up to 2.72 μWh/cm², still maintain excellent performance under harsh bending. The strategy for constructing 3D nanoarchitectures and further manufacturing MSCs can inspire the design of novel electrode materials and devices to advance the development in the field of energy storage.     

Nitrogen-doped hierarchically porous carbon obtained via single step method for high performance supercapacitors

In the present work, nitrogen doped hierarchically activated porous carbon (APC) samples have been synthesized via single step scalable method using ethylene di-amine tetra acetic acid (EDTA) as precursor and KOH as activating agent. Activated porous carbons with different pore sizes have been developed by varying the activation temperature. SEM, TEM and SAXS analysis suggest that with variation of activation temperature, a hierarchical porous structure with interconnected meso-pore and micro pores has been achieved. The sufficiently high surface area of the synthesized materials provides active sites to enhance the diffusion of ions between the electrolyte and the carbon electrodes. The electrode prepared at 800 °C activated sample exhibited highest specific capacitance of 274 Fg^-1 in two electrode setup, at a current density of 0.1 Ag^-1 in 1 M aqueous H₂SO₄. Along with this, it showed maximum energy density of 9.5 Whkg^?1 at a power density of 64.5 Wkg^-1. The remarkable electrochemical performance reveals that the synthesized nitrogen doped activated carbon electrodes derived from EDTA can be tuned to have optimum pore structure and pore size distribution for better electrochemical performance, so it can be considered as a potential electrode material for applications in electrochemical energy storage.     

Good dielectric performance and broadband dielectric polarization in Ag,Nb co-doped TiO2

Due to the demand of miniaturization and integration for ceramic capacitors in electronic components market, TiO₂-based ceramics with colossal permittivity has become a research hotspot in recent years. In this work, we report that Ag⁺/Nb⁵⁺ co-doped (Ag_1/4Nb_3/4)_xTi_1−xO₂ (ANTOx) ceramics with colossal permittivity over a wide frequency and temperature range were successfully prepared by a traditional solid–state method. Notably, compositions of ANTO0.005 and ANTO0.01 respectively exhibit both low dielectric loss (0.040 and 0.050 at 1 kHz), high dielectric permittivity (9.2 × 10³ and 1.6 × 10⁴ at 1 kHz), and good thermal stability, which satisfy the requirements for the temperature range of application of X9R and X8R ceramic capacitors, respectively. The origin of the dielectric behavior was attributed to five dielectric relaxation phenomena, i.e., localized carriers' hopping, electron–pinned defect–dipoles, interfacial polarization, and oxygen vacancies ionization and diffusion, as suggested by dielectric temperature spectra and valence state analysis via XPS; wherein, electron-pinned defect–dipoles and internal barrier layer capacitance are believed to be the main causes for the giant dielectric permittivity in ANTOx ceramics.     

煤基高能量密度燃料的合成及表征

高能量密度燃料是为新型高性能飞行器提供动力保障的关键,其合成及应用研究具有重要的前瞻性和重大战略意义。煤炭是我国的主体能源和重要原料,通过煤直接转化获取的煤基油,充分保留了煤中特有的环状分子化学结构,具有良好的热安定性和较高的能量密度,被认为是高超音速飞行器的优选燃料。以煤直接液化工艺生产的煤液化石脑油馏分为起始原料,通过富集轻质芳烃、化学合成、催化加氢稳定和产物分离提纯等方法制备煤基高能量密度燃料,并对其产物进行分子结构表征和性能评价。结果表明,煤直接液化生产的石脑油馏分是一种优异的催化重整原料,经催化重整富集轻质芳烃后,其轻质芳烃质量分数高达71.05%。Diels-Alder化学合成主产物是由多个封闭环平面组成且具有空间立体构型的二环或三环烃类物质,质量分数为46.18%,因分子内存在较大的张力能,结构紧凑,其拥有更大的密度和体积热值。煤基高能量密度燃料的密度和体积热值分别为0.8990 g/cm3与38.06 MJ/L,均大大超过现行的国内石油基喷气燃料(RP-3和RP-6)、煤基大比重喷气燃料、美国和俄罗斯军用标准。与单一纯物质合成高能量密度燃料(JP-10和T-10)比较,其密度与体积热值偏小。究其原因主要是轻质芳烃的富集度仅为71.05%,需进一步提高其轻质芳烃质量分数。另外,制备的煤基高能量密度燃料种类复杂,其主产物质量分数仅46.18%,下一步可重点调控合成产物的分子构型和纯化分离。     

Ni2V2O7 dandelion microsphere for a high-performance electrocatalyst in water splitting

Water splitting is an effective way to produce hydrogen to solve the energy crisis problem, and inorganic metal compounds are widely used in electrocatalysis field due to efficient hydrogen evolution reaction (HER). Herein, we synthesize Ni₂V₂O₇ dandelion microsphere from nickel nitrate and vanadium pentoxide by “one-step hydrothermal” way, which exhibits large specific surface area of 102.74 m² g⁻¹. The as-prepared Ni₂V₂O₇ microsphere shows good electrocatalysis performances including OER overpotential of 358 mV and good stability, as well as HER overpotential of 195 mV. Furthermore, the Ni₂V₂O₇ microsphere electrode is assembled to Ni₂V₂O₇ microsphere//Ni₂V₂O₇ microsphere system, showing the water splitting voltage of 1.50 V at 10 mA cm⁻² by two-electrode method, which is much lower than those of commercial RuO₂//Pt/C system and most of spinel oxides electrocatalysts. Our work opens up a new and facile avenue for fabricating inorganic microsphere electrocatalyst in hydrogen production field.     

Specific emitter identification for satellite communication using probabilistic neural networks

Electromagnetic signal emitted by satellite communication (satcom) transmitters are used to identify specific individual uplink satcom terminals sharing the common transponder in real environment, which is known as specific emitter identification (SEI) that allows for early indications and warning (I&W) of the targets carrying satcom furnishment and furthermore the real time electromagnetic situation awareness in military operations. In this paper, the authors are the first to propose the identification of specific transmitters of satcom by using probabilistic neural networks (PNN) to reach the goal of target recognition. We have been devoted to the examination by exploring the feasibility of utilizing the Hilbert transform to signal preprocessing, applying the discrete wavelet transform to feature extraction, and employing the PNN to perform the classification of stationary signals. There are a total of 1000 sampling time series with binary phase shift keying (BPSK) modulation originated by five types of satcom transmitters in the test. The established PNNs classifier implements the data testing and finally yields satisfactory accuracy at 8 dB(±1 dB) carrier to noise ratio, which indicates the feasibility of our method, and even the keen insight of its application in military.     

双螺线圈式液压油微污染物检测传感器

设计了一种多参数的油液污染物检测传感器,该传感器在单螺线圈电感式传感器的基础上,增加了一个螺线管线圈,可以进行电感检测和电容检测。电感检测可以区分油液中的铁磁性颗粒和非铁磁性颗粒;电容检测可以区分油液中水和空气。相对于传统单线圈式传感器,本次设计不仅实现了油液污染物的多参数检测,同时采用线径更小、匝数更多的螺线圈,增加了传感器的检测灵敏度。利用该传感器搭建的实验平台进行检测实验:电感检测时可以检测直径大于20μm的铁颗粒和直径大于80μm的铜颗粒;电容检测时可以检测直径大于90～100μm水滴和直径大于160～170μm气泡。该设计研究为油液污染物快速检测提供了一种新的方法,对于机械设备故障诊断与寿命预测等领域具有一定的意义。