Thermal depolarization and electromechanical hardening in Zn2+-doped Na1/2Bi1/2TiO3-BaTiO3

Na_1/2Bi_1/2TiO₃-based materials have been earmarked for one of the first large-volume applications of lead-free piezoceramics in high-power ultrasonics. Zn²⁺-doping is demonstrated as a viable route to enhance the thermal depolarization temperature and electromechanically harden (1-y)Na_1/2Bi_1/2TiO₃-yBaTiO₃ (NBT100yBT) with a maximum achievable operating temperature of 150 °C and mechanical quality factor of 627 for 1 mole % Zn²⁺-doped NBT6BT. Although quenching from sintering temperatures has been recently touted to enhance T_F-R, with quenching the doped compositions featuring an additional increase in T_F-R by 17 °C, it exhibits negligible effect on the electromechanical properties. The effect is rationalized considering the missing influence on conductivity and therefore, negligible changes in the defect chemistry upon quenching. High-resolution diffraction indicates that Zn²⁺-doped samples favor the tetragonal phase with enhanced lattice distortion, further corroborated by ²³Na Nuclear Magnetic Resonance investigations.     

Microstructural and mechanical properties assessment of transient liquid phase bonding of CoCuFeMnNi high entropy alloy

The transient liquid phase (TLP) bonding of CoCuFeMnNi high entropy alloy (HEA) was studied. The TLP bonding was performed using AWS BNi-2 interlayer at 1050 °C with the TLP bonding time of 20, 60, 180 and 240 min. The effect of bonding time on the joint microstructure was characterized by SEM and EDS. Microstructural results confirmed that complete isothermal solidification occurred approximately at 240 min of bonding time. For samples bonded at 20, 60 and 180 min, athermal solidification zone was formed in the bonding area which included Cr-rich boride and Mn₃Si intermetallic compound. For all samples, the γ solid solution was formed in the isothermal solidification zone of the bonding zone. To evaluate the effect of TLP bonding time on mechanical properties of joints, the shear strength and micro-hardness of joints were measured. The results indicated a decrement of micro-hardness in the bonding zone and an increment of micro-hardness in the adjacent zone of joints. The minimum and maximum values of shear strength were 100 and 180 MPa for joints with the bonding time of 20 and 240 min, respectively.     

Nacre-Inspired,Liquid Metal-Based Ultrasensitive Electronic Skin by Spatially Regulated Cracking Strategy

The realization of liquid metal-based wearable systems will be a milestone toward high-performance, integrated electronic skin. However, despite the revolutionary progress achieved in many other components of electronic skin, liquid metal-based flexible sensors still suffer from poor sensitivity due to the insufficient resistance change of liquid metal to deformation. Herein, a nacre-inspired architecture composed of a biphasic pattern (liquid metal with Cr/Cu underlayer) as “bricks” and strain-sensitive Ag film as “mortar” is developed, which breaks the long-standing sensitivity bottleneck of liquid metal-based electronic skin. With 2 orders of magnitude of sensitivity amplification while maintaining wide (>85%) working range, for the first time, liquid metal-based strain sensors rival the state-of-art counterparts. This liquid metal composite features spatially regulated cracking behavior. On the one hand, hard Cr cells locally modulate the strain distribution, which avoids premature cut-through cracks and prolongs the defect propagation in the adjacent Ag film. On the other hand, the separated liquid metal cells prevent unfavorable continuous liquid-metal paths and create crack-free regions during strain. Demonstrated in diverse scenarios, the proposed design concept may spark more applications of ultrasensitive liquid metal-based electronic skins, and reveals a pathway for sensor development via crack engineering.     

煅烧条件对模拟高放废液煅烧产物物理化学性质的影响

模拟高放废液在回转煅烧过程中容易粘壁，影响其及时输送。为了实现转形工艺和固化工艺的顺利衔接，需要通过改变工艺条件来使煅烧产物顺利出料。同时煅烧条件的变化会导致煅烧产物物理化学性质发生变化。采用动力堆燃耗45 GWd/t（以U计）乏燃料后处理产生的模拟高放废液，研究了不同温度、不同转速条件下煅烧产物的粒径分布、含水量、振实密度、脱硝率等物理化学性质，研究结果显示：升高煅烧温度可以使煅烧产物粒径更加均匀，当煅烧温度在600～700 ℃、转速在15～20 r/min时，煅烧产物的含水率小于2%，振实密度在1.7 g/cm³左右，脱硝率能达到99%以上，煅烧过程中的粘壁现象较少，能实现煅烧过程中的顺利出料。     

Tunable multicolor upconversion luminescence of Yb3+ sensitized Na3La(VO4)2 crystals

Multicolor upconversion luminescence materials show significantly applications in materials science. In this paper, the novel Yb³⁺-sensitized Na₃La(VO₄)₂ upconversion luminescence crystals are synthesized by the solid-state reaction method. Three primary colors upconversion luminescence are successfully achieved in Na₃La(VO₄)₂:Yb³⁺,Tm³⁺, Na₃La(VO₄)₂:Yb³⁺,Er³⁺, and Na₃La(VO₄)₂:Yb³⁺,Ho³⁺ crystals excited by the single 980 nm LD. Multicolor upconversion luminescence can be obtained by simply adjusting the combination ratios of these three samples. Luminescence mechanisms of the Yb³⁺-sensitized system are discussed in detail. In the Na₃La(VO₄)₂ host material, the Yb³⁺/Ho³⁺ codoped system exhibits unusual red upconversion luminescence based on the short decay time of Ho³⁺ ion ⁵I₆ level, which provides the possibility of three primary color luminescence under 980 nm excitation.     

三代压水堆内陆厂址放射性流出物排放问题及改进建议

由于内陆厂址受纳水体容量有限,使得核电内陆厂址面临的一个关键问题就是液态流出物排放。本文通过对比分析三代压水堆内陆厂址液态流出物排放与现有排放国家标准要求,发现三代压水堆两项指标不能满足内陆厂址要求,即除氚、¹⁴C外其他放射性核素和氚排放均不能满足内陆厂址要求。针对除氚、¹⁴C外其他放射性核素排放,建议增加化学絮凝、离子交换床和反渗透装置以满足100 Bq/L的排放要求。针对氚排放,通过调整排放方式能满足2台机组氚排放要求,使得下游1 km处氚浓度不超过71 Bq/L;多机组内陆电厂的氚排放建议利用联合电解催化交换(CECE)和水精馏(WD)技术,以达到分离氚的目的。     

Spontaneous Directional Self-Cleaning on the Feathers of the Aquatic Bird Anser cygnoides domesticus Induced by a Transient Superhydrophilicity

In nature, the feathers of the goose Anser cygnoides domesticus stay superhydrophobic over a long term, thought as the main reason for keeping the surface clean. However, contaminants, especially those that are oleophilic or trapped within textures, cannot be removed off the superhydrophobic feathers spontaneously. Here, a different self-cleaning strategy based on superhydrophilic feathers is revealed that is imparted by self-coating of the amphiphilic saliva, which enables removing away low-surface-tension and/or small-size contaminants by forming directional water sheeting depending on their unique anisotropic microstructures. Particularly, the surface superhydrophilicity is switchable to superhydrophobicity upon exposure to air for maintaining a clean surface for a long time, which is further enhanced by coating with self-secreted preening oil. By alternate switching between a transient superhydrophilicity and a long-term stable superhydrophobicity, the goose feathers exhibit an integrated smart self-cleaning strategy, which is also shared by other aquatic birds. An attractive point is the re-entrant structure of the feathers, which facilitates not only liquid spreading on superhydrophilic feathers, but also long-term stability of the cleaned surface by shedding water droplets off the superhydrophobicity feathers. Thus, artificial self-cleaning microtextures are developed. The result renews the common knowledge on the self-cleaning of aquatic bird feathers, offering inspiration for developing bioinspired self-cleaning microtextures and coatings.     

抑霜型空气源热泵机组应用实测研究

空气源热泵结霜过程会恶化机组的实际运行性能，重霜工况下尤为严重，发展抑霜型空气源热泵是保障其高效适用和良性发展的关键。本文依托四川省康定市的某住宅示范工程，开展抑霜型空气源热泵和常规型空气源热泵的现场实测研究，研究抑霜型空气源热泵实际应用中的抑霜、制热性能表现，并进行技术经济性分析。结果表明：抑霜型空气源热泵抑霜效果显著，制热性能得到显著改善，能效提升达到21%~37.3%，费用年值比常规空气源热泵降低了13%，1年左右即可回收追加的投资，具有更好的技术经济性，有助于空气源热泵技术在严重结霜气候区域的高效应用。     

Cheese ripening in nonconventional conditions: A multiparameter study applied to Protected Geographical Indication Canestrato di Moliterno cheese

A multiparameter study was performed to evaluate the effect of fondaco, a traditional ripening cellar without any artificial temperature and relative humidity control, on the chemical, microbiological, and sensory characteristics of Protected Geographical Indication Canestrato di Moliterno cheese. Ripening in such a nonconventional environment was associated with lower counts of lactococci, lactobacilli, and total viable bacteria, and higher presence of enterococci, in comparison with ripening in a controlled maturation room. Moreover, fondaco cheese underwent accelerated maturation, as demonstrated by faster casein degradation, greater accumulation of free AA, and higher formation of volatile organic compounds. Secondary proteolysis, as assessed by liquid chromatography-mass spectrometry of free AA and low molecular weight peptides, did not show any qualitative difference among cheeses, but fondaco samples evidenced an advanced level of peptidolysis. On the other hand, significant qualitative differences were observed in the free fatty acid profiles and in the sensory characteristics. Principal component analysis showed a clear separation of the fondaco and control cheeses, indicating that ripening in the natural room conferred unique sensory features to the product.