基于电信号特征分析的电机故障诊断技术

介绍了电机故障诊断技术平台的组成,分析了电机常见故障下电信号的特征。利用宜昌和景洪工厂两台电机进行了实际对比测试,宜昌工厂电机定子电流特征频率在49.2Hz时表现出峰值-36.08dB,在50.8Hz时表现峰值则为-37.23dB,表明电机存在转子断条故障;景洪工厂电机在转子特征频率为113.51Hz时,出现峰值-58.47dB,表明电机存在静态偏心故障。经电机现场抽芯检查,验证了电机故障快速诊断平台给出的电机健康状态评估结果,证实了基于电信号特征分析的电机故障诊断技术的准确性。     

基于Massive MIMO及频谱叠加的5G SA网络上行优化方法

大规模多输入多输出(Multiple-Input Multiple-Output, MIMO)可以有效提升5G SA网络的上行链路数据传输速率以及可靠性。针对5G SA网络上行链路速率和覆盖不均衡的情况,提出了基于大规模MIMO的分组算法,将发送信号矢量进行分组,组内采用最大似然检测,组外采用基于正交三角分解(QR分解)的干扰消除检测,并且结合5G频谱的叠加策略,在降低算法复杂度的同时,有效提升网络覆盖和速率。通过5G SA现网实测,通过MIMO降低分组数量能够提升分组检测性能,结合上行低频段频谱叠加策略能够有效提升5G SA网络上行覆盖30%,提升5G SA网络上行平均速率40%~80%,特别是弱覆盖边缘的网络速率,最高可达600%。     

激光在线测厚振动分析与精度优化

激光测厚具有安全可靠、测量精度高、测量范围大等优点,广泛应用于纸张、电池极片等薄膜类材料厚度的在线测量。带材宽幅方向扫描测厚时由于扫描架往复运动会产生机械振动,影响在线测厚精度。针对该问题,以锂离子电池极片厚度测量为例,使用双激光差动式测厚平台对电池极片和铜箔分别进行厚度测量,然后对测厚数据进行频谱分析,探究其振动规律的相似性,并基于频谱分析结果采用滑动带阻滤波方式对测厚数据进行处理,滤波后极片和铜箔的厚度极差分别降低了33.4%和73.8%,有效过滤了机械振动导致的测量误差,可满足极片和铜箔厚度测量的精度要求。     

Saliency4ASD: Challenge,dataset and tools for visual attention modeling for autism spectrum disorder

The recent studies showing that gaze features can be useful in the identification of Autism Spectrum Disorder (ASD), have opened a new domain where Visual Attention (VA) modeling could be of great help. In this sense, this paper presents a report of the Grand Challenge “Saliency4ASD: Visual attention modeling for Autism Spectrum Disorder”, organized at IEEE ICME’19, aiming at supporting the research on VA modeling towards this healthcare societal challenge. In particular, this paper describes the workflow, obtained results, and datasets and tools that were used within this activity, in order to help on the development and evaluation of two types of VA models: (1) to predict saliency maps that fit gaze behavior of people with ASD, and (2) to identify individuals with ASD from typical development.     

碳酸性侵蚀与AAR作用下纳米混凝土的耐久性

地铁混凝土处于地下空间,容易受到地下水的碳酸性侵蚀；碱集料反应 (AAR)是一种严重的混凝土耐久性问题,既难以发现又难以修补,由两者共同作用引起的混凝土耐久性降低严重影响地铁隧道的正常使用.为研究纳米材料对地铁混凝土在碳酸性侵蚀和AAR共同作用下耐久性的影响,在普通混凝土中掺入适量纳米SiO₂和纳米Fe₂O₃,利用自行研制的碳酸性侵蚀试验箱进行试验,采用碳酸性侵蚀深度、膨胀率和声速作为测试指标来评价纳米混凝土在碳酸性侵蚀和AAR共同作用下的耐久性.试验结果表明:掺入纳米颗粒后,混凝土的膨胀率和侵蚀深度有了明显降低,而声速有了明显提升,说明纳米混凝土的耐久性优于普通混凝土；在182 d龄期时,掺量为2%的纳米SiO₂混凝土耐久性改善最明显,侵蚀深度和膨胀率最小,声速最大且声速下降幅度最小；其次是掺量为1%的纳米Fe₂O₃混凝土.由于纳米颗粒特殊的物理化学性质,改善了混凝土内部的微观结构和孔溶液的化学组成,使碳酸性侵蚀和碱集料反应共同作用下混凝土的耐久性得到了提高.     

纤维基表面增强拉曼基底的研究进展

为解决传统纤维表面拉曼增强(SERS)基底所存在的稳定性差、操作不便等问题。介绍了柔性SERS基底的优势,总结了目前各类纤维基SERS基底的研究进展及其在痕量检测领域的应用,简述了电磁增强和化学增强2种表面增强拉曼现象的基本原理。综述了纤维纸基SERS、织物基SERS、散纤维及纳米纤维膜SERS基底的制备方法及其应用,并着重介绍了织物基SERS材料的研究现状及其在在线检测应用方面的挑战与机遇。基于织物基SERS材料高度灵敏及灵活检测的特点,展望了其作为可穿戴传感器件用于即时检测和周身环境监测的前景,为拓展智能纺织品的应用领域开辟了新的思路。     

超临界蒸汽参数对燃气蒸汽联合循环性能影响研究

为进一步提高联合循环效率,参考现有燃气蒸汽联合循环12.5 MPa/568℃亚临界蒸汽参数,提出27 MPa/585℃超临界蒸汽参数,根据燃气蒸汽联合循环计算模型,以397 MW燃气轮机联合循环机组为例,计算了超临界蒸汽参数与两种亚临界蒸汽参数的底循环效率和联合循环效率,并分析对比了3种蒸汽参数的底循环效率对联合循环效率的贡献。研究表明:对于同一燃气轮机,超临界和亚临界中低压蒸汽参数不同时,超临界蒸汽参数的底循环效率比亚临界提高了4.3%,蒸汽底循环输出功率占联合循环机组输出功率的百分比由30.21%增加到32.62%,联合循环净效率增加了2.21%,联合循环机组的输出功率增加了20.38 MW;中低压蒸汽参数相同时,超临界蒸汽参数的底循环效率比亚临界提高了2.87%,蒸汽底循环输出功率占联合循环机组输出功率的百分比由31.16%增加到32.62%,联合循环净效率增加了1.44%,联合循环机组的输出功率增加12.5 MW。     

Experimental investigation on the plasma morphology of ablative pulsed plasma thruster with tongue-shaped and flared electrodes

Ablative pulsed plasma thrusters(APPTs) are considered as an attractive propulsion option for station-keeping and drag makeup purposes for mass-and power-limited satellites. In order to understand the physical mechanism of APPTs, high-speed camera and optical emission spectroscopy are utilized to investigate the plasma characteristics including the spatial distribution and composition between the electrodes. The plume images and spectra at different times and positions are experimentally recorded, and the spatial distribution, composition, and trajectory of plasmas can be concluded through analyzing them. With the increase of the distance from the ablation surface, two clusters of plasmas near the anode and cathode meet downstream,and the species and density of plasmas tend to be uniform.     

Combined constant speed control method for a wind generator equipped with hydraulic energy storage

A wind generator equipped with hydraulic energy storage (WG‐HES) uses hydraulic transmission systems instead of gearbox transmissions, thus eliminating high‐power converters and reducing the tower‐top cabin weight. When there is no wind or the wind speed is extremely low, the pressured oil released by accumulators is used to drive a motor to operate at a constant speed, thereby generating constant‐frequency power. However, few studies have examined the constant speed control characteristics for generating electricity using only an accumulator group. In this study, a combined constant speed (CCS) proportional–integral–derivative (PID) control method based on “variable displacement and throttling” is proposed, which includes two closed loops and one regulating loop. First, a simulation model of the CCS PID control method for a variable motor was established in the Simcenter Amesim program. The influence of different PID parameters on the anti‐interference ability of the constant speed control of the motor was analyzed under a given load step. Then, we obtained the range of control parameter values and a set of optimal values. Second, the effectiveness of the CCS control method and the accuracy of the simulation results were verified on a 600‐kW WG‐HES system prototype. The results verified that the CCS control method has good anti‐interference ability and can meet the requirements of constant speed control for a variable motor under the best PID parameters. These results can provide a basis for developing control strategies for WG‐HESs when there is no wind or at low wind speeds.