Effect of microwave sintering on the microstructure and mechanical properties of AA7075/B4C/ZrC hybrid nano composite fabricated by powder metallurgy techniques

AA7075 + 6%B4C+3%ZrC nano hybrid composite was successfully fabricated, with nano reinforcements composition in AA7075 alloy selected based on previous investigation, to achieve better mechanical performance. Two different sintering techniques, namely conventional and microwave, were implemented to determine the effect on microstructural and mechanical properties. Microstructural investigation was performed with the help of W-SEM. Tensile, compression, and hardness were measured with the help of UTM and Vickers microhardness machine. Porosity was calculated by using Archimedes principle. It was observed that the added nano ZrC particles formed agglomerates and the B₄C particles were distributed homogenously. Composites processed by microwave sintering showed excellent mechanical properties compared to the conventionally sintered composites. No intermetallic compounds were detected in microwave sintered composites through XRD analysis, indicating strong and clean interface bonds between matrix and reinforcement particles. High strain to fracture value of 12.24% was noted in microwave sintered nano hybrid composite, while it was 6.12% for conventional sintered one. Fractography revealed no peeling action of reinforcements from the matrix material, and the mode of failure was brittle. It was concluded that, while fabricating nano range hybrid composites, the implementation of advanced sintering technique (microwave sintering) with low sintering temperatures and low sintering times with internal heat generations, helps in eliminating defects that may develop because of high surface energies of nano range reinforcements.     

Influence of high energy ball milling on structural,microstructural and optical properties of TiO2 nanoparticles

The influence of high-energy ball milling on structural, microstructural, and optical properties of TiO₂ by modifying the nanoparticle size was studied. Five samples were extracted at different milling times (0, 2, 4, 8, and 13 h). The average particle sizes estimated by dynamic light scattering (DLS) were 205, 155.8, 116.8, 82.9, and 82.7 nm at 0, 2, 4, 8, and 13 h, respectively. X-ray diffraction analysis confirmed progressive broadening of the peaks as the milling time elapsed. Besides, a correlation was found between d spacing and the average crystal size. The UV–Vis diffuse reflectance spectra of TiO₂ revealed a decrease in reflectance due to particle size reduction. Similarly, an alteration of the bandgap transition energy was presented, whose values gradually decreased from 2.966 eV to 2.861 eV for the sample without and with the maximum duration milling performed (13 h), respectively. Likewise, the SEM analysis showed a distribution in nanoparticle size that became more homogeneous and smaller average grain size as the milling duration was longer.     

New horizon in mechanochemistry—high-temperature,high-pressure mechanical synthesis in a planetary ball mill—with magnesium hydride synthesis as an example

A new route of materials synthesis, namely, high-temperature, high-pressure reactive planetary ball milling (HTPRM), is presented. HTPRM allows for the mechanosynthesis of materials at fully controlled temperatures of up to 450 °C and pressures of up to 100 bar of hydrogen. As an example of this application, a successful synthesis of magnesium hydride is presented. The synthesis was performed at controlled temperatures (room temperature (RT), 100, 150, 200, 250, 300, and 325 °C) while milling in a planetary ball mill under hydrogen pressure ($>$50 bar). Very mild milling conditions (250 rpm) were applied for a total milling time of 2 h, and a milling vial with a relatively small diameter (φ = 53 mm, V = ～0.06 dm³) was used. The effect of different temperatures on the synthesis kinetics and outcome were examined. The particle morphology, phase composition, reaction yield, and particle size were measured and analysed by scanning electron microscopy, X-ray diffraction, differential scanning calorimetry (DSC) techniques. The obtained results showed that increasing the temperature of the process significantly improved the reaction rate, which suggested the great potential of this technique for the mechanochemical synthesis of materials.     

Structural and electrical studies of excessively Sm2O3 substituted soft PZT nanoceramics

The solid solution of Pb_1-x Sm_2x/3 (Zr_0.6 Ti_0.4) O₃ ceramics with x = 0.1, 0.2, 0.3, and 0.4 was prepared via the high-energy ball milling technique. Further, the effect of excessive Sm₂O₃ substitution at Pb-site on structural, dielectric, and dc-conductivity properties was studied. The X-ray diffraction (XRD) analysis confirmed that all samples were crystallized with perovskite and pyrochlore diphase form. Excess Sm³⁺ substitution in the PZT system increases the pyrochlore volume fraction from 5 to 20% and induces a structural phase transition from rhombohedral to a tetragonal structure. The microstructural study by TEM and SEM indicated that the particles were spherical with an average size of 43–55 nm. The frequency and temperature-dependent dielectric constant for all compositions was carried out and it is obtained that the dielectric constant decreases with Sm³⁺ content. The phase transition temperature first decreases up to x = 0.2 and then increases for the higher concentration of samarium. The dc-conductivity studies revealed that all samples showed an unusual mixed TCR effect (both positive and negative temperature coefficient of resistance). Such properties of the studied samples indicate that the material is suitable for potential applications in thermistors, and temperature sensors of the automotive, and petroleum industries.     

Hydrogen desorption from alloys Mg–Cu(–KCl): Cu catalysis in detail

Effect of chemical composition of Mg-xCu based alloys (x = 9.94–58.00 wt %) modified by KCl upon their hydrogen storage performance was studied. Kinetic curves and pressure-concentration isotherms were measured in the ranges up to 60 bar and 388 °C, respectively. It was observed that desorption rate dc/dt is not significantly influenced by the composition. Unknown Cu-rich phase was detected that has shown a catalytic effect on desorption from a mixture with other phases. Activation energy of hydrogen desorption decreased with increasing x from 180 kJ/mol down to 98 kJ/mol. Average hydride dissociation enthalpy, ΔH, for the lowest plateau was 75 kJ/mol which is equal to literature value for pure Mg. Slightly lover average value, 67 kJ/mol was obtained for the second plateau and ΔH for the third one decreased from 70 kJ/mol for the lowest to 49 kJ/mol for the highest x.     

碘化多壁碳纳米管制备含有Ag/MWCNTs复合材料的银-环氧树脂浆料

提出一种将多壁碳纳米管碘化后制备银/多壁碳纳米管（Ag/MWCNTs）复合材料的方法。通过球磨对碘化多壁碳纳米管进行了功能化，并通过透射电子显微镜（TEM）、X射线衍射（XRD）、傅里叶变换红外光谱（FT-IR）、拉曼光谱和热重分析（TG）对其进行了表征。结果表明，经碘化处理后，银纳米粒子（Ag-NPs）能更好地粘附在碳纳米管表面，改善了银纳米粒子与碳纳米管之间的连接。羟基（-OH）基团的伸缩振动明显增强，激活了碳纳米管的表面，增加了碳纳米管表面Ag⁺形核的数量。在260 ℃以下，Ag/MWCNTs复合材料的质量损失小于MWCNTs的质量损失。最后，制备了银-环氧树脂浆料，发现使用Ag/MWCNTs复合物制备的浆料具有最低的电阻率和最高的热导率。     

M- S-H formation in MgO-SiO2slurries via wet milling for magnesia based castables

It is believed that the formation of hydration phase, MgO-SiO₂-H₂O (M-S-H), contributes to good workability and reliable comprehensive properties for magnesia based castables. In order to stimulate the formation of M-S-H in magnesia based castables and understand the minimum introduction of microslica amount, wet milling process was used to promote the dissolution of MgO and SiO₂ in this work. The slurry containing different content of microsilica with wet milling technology and the castables with/without wet milling slurry were prepared. The effects of microsilica content on the formation of hydration phases were analyzed by XRD, FT-IR and TG/DSC and the properties of magnesia based castables were evaluated by explosion resistance, CMOR, HMOR and so on. The results showed that the formation of M-S-H was accelerated because of the dissolution of Mg²⁺ and HSiO₃^? in wet milling process. Higher amount of M-S-H led to a tight bonding in the early stage, and a denser structure after firing at high temperature due to the limited formation of brucite and in-situ formation of evenly distributed forsterite phase. In addition, much higher HMOR were obtained when less microsilica was added, attributing to the suppressed formation of low-melting-point liquid. Therefore, 2–3 wt% microsilica addition was recommended in this process.     

基于VERICUT的偏心放置分段式齿圈铣齿方法研究

为解决大直径且齿宽较宽的分段式齿圈的铣齿问题,提出采用偏心放置的主程序调用子程序循环加工的铣齿方法。根据主程序数学模型和子程序数学模型构建偏心放置铣齿方法的数学模型,基于VERICUT的仿真模型和仿真主、子程序,实现齿槽的开粗和精铣仿真加工;通过VERICUT对比分析功能模块,以齿面残留模型为依据,验证了偏心放置铣齿方法的可行性。