混凝土结构的压电声波检测分析

本文介绍了混凝土结构的压电体波和表面波检测的主要进展,对两种压电声波检测的优缺点进行了总结。体波检测设备一般埋入混凝土内部,需要选择合理的检测部位,检测结果较为精确;声表面波检测无需选择特定的部位,但是检测深度有限。在实际检测工作过程中,可以联合两种方法相互验证。     

Bio-Based,Self-Crosslinkable Eucommia ulmoides Gum/Silica Hybrids with Body Temperature Triggering Shape Memory Capability

At present, the synthesis of body temperature triggering shape memory polymers usually requires elaborate structural design, which limits their wide application. Herein, starting from bio-based Eucommia ulmoides gum (EUG), a series of EUG/silica hybrids (ESHs) are prepared through a facile one-pot process, in which EUG is epoxied and then self-crosslinked with SiO₂ by epoxy ring-open reaction. Varying the amount of H₂O₂, the shape memory transition temperature (T_trans) of ESHs is adjusted to 47.4–36.6 ℃, which is close to human body temperature (37 ℃). Among them, ESH-17 exhibited the best body temperature triggering shape memory ability (T_trans = 36.6 ℃), which can restore the permanent shape within 60 s at 37 ℃ with a shape fixity ratio of 99% and shape recovery ratio near 100%. In addition, the shape memory mechanism is discussed and shows some application scenarios of ESHs. The as-produced materials can be used as smart biomaterials such as self-tightening sutures, self-sealing root canal filling materials, and so on.     

Environmentally Friendly Graphene Inks for Touch Screen Sensors

Graphene-based materials have attracted significant attention in many technological fields, but scaling up graphene-based technologies still faces substantial challenges. High-throughput top-down methods generally require hazardous, toxic, and high-boiling-point solvents. Here, an efficient and inexpensive strategy is proposed to produce graphene dispersions by liquid-phase exfoliation (LPE) through a combination of shear-mixing (SM) and tip sonication (TS) techniques, yielding highly concentrated graphene inks compatible with spray coating. The quality of graphene flakes (e.g., lateral size and thickness) and their concentration in the dispersions are compared using different spectroscopic and microscopy techniques. Several approaches (individual SM and TS, and their combination) are tested in three solvents (N-methyl-2-pyrrolidone, dimethylformamide, and cyrene). Interestingly, the combination of SM and TS in cyrene yields high-quality graphene dispersions, overcoming the environmental issues linked to the other two solvents. Starting from the cyrene dispersion, a graphene-based ink is prepared to spray-coat flexible electrodes and assemble a touch screen prototype. The electrodes feature a low sheet resistance (290 Ω □⁻¹) and high optical transmittance (78%), which provide the prototype with a high signal-to-noise ratio (14 dB) and multi-touch functionality (up to four simultaneous touches). These results illustrate a potential pathway toward the integration of LPE-graphene in commercial flexible electronics.     

Borage Oil Enhances Lamellar Body Content and Alters Fatty Acid Composition of Epidermal Ceramides in Essential Fatty Acid-Deficient Guinea Pigs

Borage oil [BO: 40.9% linoleic acid (LNA) and 24.0% γ-linolenic acid (GLA)] reverses disrupted epidermal lipid barrier in essential fatty acid deficiency (EFAD). We determined the effects of BO on lamellar body (LB) content and LNA and GLA incorporation into epidermal ceramide 1 (CER1) and epidermal ceramide 2 (CER2), major barrier lipids. EFAD was induced in guinea pigs by a diet of 6% hydrogenated coconut oil (HCO) for 10 weeks (group HCO) or 8 weeks followed by 6% BO for 2 weeks (group HCO + BO). LB content and LNA and GLA incorporation into CER1 were higher in group HCO + BO than in group HCO. Small but significant levels of LNA, GLA, and their C20-metabolized fatty acids [dihomo-γ-linolenic acid (DGLA) and arachidonic acid (ARA)] were incorporated into CER2, where ARA was detected at a level lower than LNA, but DGLA incorporation exceeded that for GLA in group HCO + BO. Dietary BO enhanced LB content and differential incorporation of GLA into CER1 and DGLA into CER2.     

基于归一化水体指数及其阈值自适应算法的水体遥感反演效果分析

归一化水体指数（NDWI）是水体遥感反演的一种重要指标，其阈值及修正直接影响反演结果的精度。基于Landsat-8与GF-1光学多光谱影像，使用归一化水体指数法阈值0（TH₀）、最大类间方差法（OTSU）自适应阈值（TH_otsu）与均值漂移聚类算法（Mean-Shift）自适应阈值（TH_MS）分别对典型正常水体、云雾覆盖水体、富营养化水体、高含泥沙水体进行水体遥感提取与效果分析，结果表明：正常水体以TH₀为阈值提取精度最高，THMS提取精度次之，TH_otsu提取精度最差；而云雾覆盖水体、富营养化水体以及含泥沙水体使用THMS提取精度最高，尤其少量云雾覆盖下的水体，TH_MS具有更明显的优势，TH₀提取精度次之，TH_otsu提取精度最差；对于不同的阈值，Land?sat-8比GF-1总体表现出更高的水体提取精度。Mean-Shift算法应用于NDWI阈值修正与水体遥感反演具有快速、水质适应性强、效果稳定的优势，对尤其是复杂条件下的水体信息遥感反演具有较好的提取效果。     

断控岩溶主控的缝洞型碳酸盐岩内部溶蚀相带表征——以塔河油田10区奥陶系油藏为例

以塔河油田10区的典型井组为研究对象，在明确断裂主控岩溶的背景下，分析岩溶作用过程与缝洞空间分布的关系，揭示了研究区缝洞体内幕结构及油气生产差异机理。通过对钻井、地震、示踪剂等动态和静态资料的分析，将研究区缝洞储集体划分为洞穴型、孔洞型、裂缝-孔洞型和裂缝型4种类型。结合地球物理描述与相似露头观察，分析断控岩溶作用下溶洞的发育过程，并建立基于成因演化的缝洞空间分布模式。岩溶作用下储层的发育具有分带性，依据该模式从内向外划分出4个溶蚀相带，分别是大型溶洞带、溶蚀孔洞密集区、缝洞联合发育体以及最外围的裂缝破裂带。不同的溶蚀相带其发育的主要储集体类型、储集物性、井震特征以及储量和产能情况有较大差异。在此基础上，结合生产动态资料所揭示的不同井之间的响应和连通情况，明确了研究区不同钻井分别钻遇了不同发育程度或演化阶段的缝洞溶蚀相带，且主要存在溶洞连通、缝洞连通和裂缝连通3种沟通方式。通过对缝洞溶蚀相带空间配置关系的有效刻画，采用确定性建模方法建立岩溶储层三维地质模型，并取得较好的数值模拟效果。     

适用于无线体域网的动态口令认证协议

无线体域网中传输的是与生命高度相关的敏感数据，身份认证是信息安全保护的第一道防线。现有的基于人体生物信息的身份认证方案存在信息难提取、偶然性大和误差性大的问题，基于传统密码学的认证方案需较大计算资源和能量消耗，并不适用于无线体域网环境。为此，在动态口令和非对称加密机制基础上，提出一种适用于无线体域网的动态口令双向认证轻量协议，并对其进行形式化分析。通过理论证明、SVO逻辑推理及SPIN模型检测得出：该协议满足双向认证，且能够抵御重放攻击、伪装攻击、拒绝服务器攻击和口令离线攻击，具有较高安全性。     

基于混合蚁群算法的异质车队低碳VRP研究

针对货运车辆在配送调度过程中产生大量碳排放的问题，建立模型将多种影响碳排放量的因素协同优化。模型中考虑了不同载重量的异质车队，两个节点之间有多条道路的柔性路径，以及车辆重量随卸货而减少的动态负载等因素，以碳排放量、行驶时间和行驶路程为优化目标，并加入了节点需求时间窗、根据速度变化划分路段、交接和卸货时间的约束。提出了一种混合蚁群算法，利用蚁群算法信息素强度更新方式保持群体记忆性，利用粒子群算法的快速收敛特性增加计算效率。通过随机数值算例的仿真优化与对比分析，验证了算法和模型的有效性。     

基于RGV轨导柔性线环境离散型零件生产过程管理与实践

为满足航空中小型结构件快速交付的需要,以提升航空中小型结构件制造高精度、自动化和高效率为目标,通过对航空中小型结构件加工现状进行梳理分析,搭建柔性生产线自动排程与调度平台,实现柔性生产线工艺设计与准备过程管理,简化工艺准备流程,推进快换工装的应用并进行自动化程序管理;在柔性生产线加工运行过程中采用可视化管理方法,推动自动化环境下加工过程资源保障集中化管理。最终使该管理方法在某项目中进行成功实践,取得了良好的经济效益。