Influence of temperature on acoustic emission source location accuracy in underground structure

An acoustic emission (AE) experiment was carried out to explore the AE location accuracy influenced by temperature. A hollow hemispherical specimen was used to simulate common underground structures. In the process of heating with the flame, the pulse signal of constant frequency was stimulated as an AE source. Then AE signals received by each sensor were collected and used for comparing localization accuracy at different temperatures. Results show that location errors of AE keep the same phenomenon in the early and middle heating stages. In the later stage of heating, location errors of AE increase sharply due to the appearance of cracks. This provides some beneficial suggestions on decreasing location errors of structural cracks caused by temperature and improves the ability of underground structure disaster prevention and control.     

Microstructure and coloring mechanism of iron spots on bluish white porcelain from Jingdezhen of the Song Dynasty

Jingdezhen is famous for its bluish white (Qingbai) porcelains of the Song Dynasty, and those decorated with iron spots are distinctive among them. Herein, iron spots on a bluish white porcelain were investigated using a series of microscopic and spectroscopic characterizations. We found the decreasing iron content from more than 8 wt% to about 2 wt% during the glaze color transition from rusty to brown and finally into green, which built a connection on the coloring mechanism of iron-rich crystallized glaze and celadon glaze. We identified the rare ε-Fe₂O₃, a promising magnetic material, in both the dark brown crystals and the triangular crystals in the rusty area, which is its first discovery among bluish white porcelains. Based on these findings, we discussed the coloring mechanism of iron-spot decoration along with the physical form of the iron oxide crystals, indicating the partially reducing atmosphere during firing process.     

爆破位置对深凹露天矿山炮烟扩散的影响研究

深凹露天矿山由于其特殊的结构,爆破产生的炮烟扩散稀释较为困难,严重危害生产作业人员的生命安全与健康。基于实际矿山构建了深凹露天矿山的二维物理及数学模型,采用非稳态数值分析方法研究了不同爆破位置下,深凹露天矿山采坑内爆破炮烟的扩散规律。研究结果表明：不同爆破位置下,露天采坑内均出现复环流,爆破点位置是影响露天采坑内风流结构特征的重要因素；露天采坑内的炮烟最高浓度均随着时间变化而逐渐下降,但下降的速率逐步减小,呈现三个阶段的下降趋势；爆破位置位于背风侧时露天采坑内的炮烟最高浓度和降至安全浓度所需时间远高于迎风侧三个爆破位置；随着背风侧爆破点距采坑底部距离的减小,炮烟最高浓度及降至安全浓度所需时间先降低后增加,炮烟最高浓度及降至安全浓度所需时间随着迎风侧爆破位置距采坑底部距离的减小而增加。研究结果对于指导深凹露天矿山企业合理组织爆破后的生产作业和保障作业人员安全具有重要意义。     

Estimates of daily oxygen consumption,carbon dioxide and methane emissions,and heat production for beef and dairy cattle using spot gas sampling

A simulation study was conducted to examine accuracy of estimating daily O₂ consumption, CO₂ and CH₄ emissions, and heat production (HP) using a spot sampling technique and to determine optimal spot sampling frequency (FQ). Data were obtained from 3 experiments where daily O₂ consumption, emissions of CO₂ and CH₄, and HP were measured using indirect calorimetry (respiration chamber or headbox system). Experiment 1 used 8 beef heifers (ad libitum feeding; gaseous exchanges measured every 30 min over 3 d in respiration chambers); Experiment 2 used 56 lactating Holstein-Friesian cows (restricted feeding; gaseous exchanges measured every 12 min over 3 d in respiration chambers); Experiment 3 used 12 lactating Jersey cows (ad libitum feeding; gaseous exchanges measured every hour for 1 d using headbox style chambers). Within experiment, averages of all measurements (FQALL) and averages of measurements selected at time points with 12, 8, 6, or 4 spot sampling FQ (i.e., sampling every 2, 3, 4, and 6 h in a 24-h cycle, respectively; FQ12, FQ8, FQ6, and FQ4, respectively) were compared. Within study a mixed model was used to compare gaseous exchanges and HP among FQALL, FQ12, FQ8, FQ6, and FQ4, and an interaction of dietary treatment by FQ was examined. A regression model was used to evaluate accuracy of spot sampling within study [i.e., FQALL (observed) vs. FQ12, FQ8, FQ6, or FQ4 (estimated)]. No interaction of diet by FQ was observed for any variables except for CH₄ production in experiment 1. No FQ effect was observed for gaseous exchanges and HP except in experiment 2 where CO₂ production was less (5,411 vs. 5,563 L/d) for FQ4 compared with FQALL, FQ12, and FQ8. A regression analysis between FQALL and each FQ within study showed that slopes and intercepts became farther from 1 and 0, respectively, for almost all variables as FQ decreased. Most variables for FQ12 and FQ8 had root mean square prediction error (RMSPE) less than 10% of the mean and concordance correlation coefficient (CCC) greater than 0.80, and RMSPE increased and CCC decreased as FQ decreased. When a regression analysis was conducted with combined data from the 3 experiments (mixed model with study as a random effect), results agreed with those from the analysis for the individual studies. Prediction errors increased and CCC decreased as FQ decreased. Generally, all the estimates from FQ12, FQ8, FQ6, and FQ4 had RMSPE less than 10% of the means and CCC greater than 0.90 except for FQ6 and FQ4 for O₂ consumption and CH₄ production. In conclusion, the spot sampling simulation with 3 indirect calorimetry experiments indicated that FQ of at least 8 samples (every 3 h in a 24-h cycle) was required to estimate daily O₂ consumption, CO₂ and CH₄ production, and HP and to detect changes in those in response to dietary treatments. This sampling FQ may be considered when using techniques that measure spot gas exchanges such as the GreenFeed and face mask systems.     

The effect of biomass feeding location on rice husk gasification for hydrogen production

The objective of this study is to investigate the impact of biomass feeding location on rice husk gasification for hydrogen production. By comparing the results between top-feed and bottom-feed of the feedstock of the fluidized bed biomass gasification at the reaction temperature between 600～1000 °C and ER = 0.2, 0.27, and 0.33 without steam, the optimum low heating value was increase by 2.35 kJ/g-rice husk by the top-feed to gasifier. Although the yield of hydrogen was decreased by 42% for the rice husk gasification by the top-feed operation, the yield of CO, CO2, and CH4 were highly increased, which enhancing the heating value of the effluent gas. The study results suggested the potential route of the biomass gasification at the different feeding location.     

YOLSO: You Only Look Small Object

Small object detection is challenging and far from satisfactory. Most general object detectors suffer from two critical issues with small objects: (1) Feature extractor based on classification network cannot express the characteristics of small objects reasonably due to insufficient appearance information of targets and a large amount of background interference around them. (2) The detector requires a much higher location accuracy for small objects than for general objects. This paper proposes an effective and efficient small object detector YOLSO to address the above problems. For feature representation, we analyze the drawbacks in previous backbones and present a Half-Space Shortcut(HSSC) module to build a background-aware backbone. Furthermore, a coarse-to-fine Feature Pyramid Enhancement(FPE) module is introduced for layer-wise aggregation at a granular level to enhance the semantic discriminability. For loss function, we propose an exponential L1 loss to promote the convergence of regression, and a focal IOU loss to focus on prime samples with high classification confidence and high IOU. Both of them significantly improves the location accuracy of small objects. The proposed YOLSO sets state-of-the-art results on two typical small object datasets, MOCOD and VeDAI, at a speed of over 200 FPS. In the meantime, it also outperforms the baseline YOLOv3 by a wide margin on the common COCO dataset.     

基于机器学习识别与标记分水岭分割的盲道图像定位

视觉导盲仪是一种旨在解决盲人出行困难的导盲设备，为了实现视觉导盲仪诱导盲人找到盲道并沿盲道行走，提出了一种基于机器学习识别与标记分水岭分割的盲道图像定位算法，通过离线训练与在线的识别、分割来定位盲道区域。首先对盲道图像进行视角变换的预处理，根据盲道的地面方程将变化的倾斜视角转换为固定的俯视视角，消除射影变换带来的失真；然后利用局部二进制模式描述子提取鸟瞰图的纹理特征，以自适应增强学习算法离线训练盲道识别分类器；进而利用分类器对鸟瞰图像进行在线识别，粗略确定盲道区域；最后将识别结果进行形态学处理后作为标记，利用标记分水岭算法得到精确分割的盲道区域并定位盲道中心线。在研制的视觉导盲仪上进行验证，结果表明盲道定位准确率达到了95.44%，速度平均每秒8帧，具有高准确率的同时达到实时性要求，为盲道的准确三维定位提供了必要条件。     

波形驱动下多参数约束高分辨率反演方法——以四川盆地渝西地区龙马溪组页岩气为例

基于叠后地震波形指示反演在薄储层预测方面的优势，以及叠前弹性参数较叠后弹性参数信息更丰富、对储层的敏感性更高的特点，根据岩石物理资料，应用地震驱动+储层构型约束的高精度叠前随机反演方法，探寻定量表征优质薄页岩的技术，以期为深层页岩气地质甜点预测提供技术支撑。首先，基于道集波形相似性、AVO特征和空间距离的三变量优选方法提取结构相似的井数据作为空间估值样本，然后建立待判别道集初始模型；其次，以统计的弹性阻抗作为先验信息，应用“基于叠前道集特征指示的马尔科夫链-蒙特卡洛随机模拟算法”进行叠前地震波形指示反演，最终得到高精度的叠前弹性参数反演成果。实际应用表明，应用所提方法有效预测了龙一段一亚段1-2小层优质页岩厚度，基于特征参数的井震高频模拟精确模拟了龙一段一亚段1-2小层地质甜点参数，为页岩气勘探提供了技术支撑。     

Location Privacy in Device-Dependent Location-Based Services: Challenges and Solution

With the evolution of location-based services (LBS), a new type of LBS has already gain a lot of attention and implementation, we name this kind of LBS as the Device-Dependent LBS (DLBS). In DLBS, the service provider (SP) will not only send the information according to the user’s location, more significant, he also provides a service device which will be carried by the user. DLBS has been successfully practised in some of the large cities around the world, for example, the shared bicycle in Beijing and London. In this paper, we, for the first time, blow the whistle of the new location privacy challenges caused by DLBS, since the service device is enabled to perform the localization without the permission of the user. To conquer these threats, we design a service architecture along with a credit system between DLBS provider and the user. The credit system tie together the DLBS device usability with the curious behaviour upon user’s location privacy, DLBS provider has to sacrifice their revenue in order to gain extra location information of their device. We make the simulation of our proposed scheme and the result convince its effectiveness.     

相对冲击位置和补片层数对胶接修理CFRP复合材料层合板抗冲击性能的影响

本文针对碳纤维增强聚合物（CFRP）复合材料修补结构，基于连续损伤力学和粘结单元模型，在ABAQUS软件中对低速冲击载荷下不同冲击位置和补片层数的CFRP复合材料层合板内部和层间损伤进行了数值分析，并与试验结果进行了对比。选择相对冲击位置为0 mm、10 mm、20 mm、30 mm和40 mm时对应的五种修补结构，通过数值计算和试验，获得了修补结构在低速冲击过程中的冲击力、冲击能量等数据。在保持补片单层厚度不变的前提下，使补片层数从1层增加到5层，计算获得了修补结构的低速冲击响应。研究结果表明：冲头接触修补结构时会对补片造成较大的损伤，补片可以提高含孔损伤母板的抗冲击性能；冲击点离修补结构损伤孔越近，结构受冲击所产生的分层损伤越严重；增加补片的层数可以提高修补结构的抗冲击性能；通过对补片层数进行优化，得到优化层数为2，其对应的修补结构与无修补结构相比分层损伤面积减少了19.9%，较好地提升了母板的抗冲击性能。