Influence of aluminum phosphate on the tribocorrosion performance of chemically bonded phosphate ceramic coatings

In this study, chemically bonded phosphate ceramic coatings (CBPCCs) with different contents of aluminum phosphate (AP) are prepared on stainless steel (AISI 304L). Differential scanning calorimetry, X-ray diffraction, contact angle test, and a tribocorrosion experiment are carried out to clarify the role of AP in the tribocorrosion performance of CBPCCs. The results show that, with the increase in the AP content, the enthalpy of curing increases because of the greater formation of the bonding phase AlPO₄. Both in static corrosion and in tribocorrosion, the corrosion current density of CBPCCs achieves the lowest value when the weight ratio of AP to polytetrafluoroethylene is about 0.78. Additionally, the influence mechanism of AP on tribocorrosion is clarified. AlPO₄ from the reaction between AP and Al₂O₃ has excellent mechanical properties and can enhance the wear resistance of CBPCCs by reducing the mechanical wear and the increased wear due to corrosion. The alumina particles wrapped by AlPO₄ can form a dense and smooth surface and change the direction of electrolyte propagation, which leads to the increase in the tribocorrosion resistance of CBPCCs.     

Electrodeposition of B,Ni co-doped diamond-like carbon films on AZ91D magnesium alloy: Corrosion and wear resistance

Diamond-like carbon (DLC) possesses brilliant and excellent properties, including excellent corrosion resistance as well as outstanding wear resistance. Ni and B co-doped DLC films were deposited on AZ91D magnesium alloy by electrodeposition under mild conditions (300 V and 25°C). Uniform and dense morphology of co-doped DLC films were observed, and Ni and B were uniformly incorporated into the carbon-based films. Among all the electrodeposits, the appearance of D and G peaks near 1330 and 1570 cm⁻¹ revealed that the as-deposited films were typical DLC films. As the addition of Ni was increased to 0.05 g, the highest microindentation hardness, the lowest friction coefficient, and wear loss were achieved to be 164.5 HV, 0.3, and 0.6 × 10⁻⁵ kg/m, respectively. The amorphous carbon films fabricated at 0.05 g Ni had the lowest corrosion current density and the most positive corrosion potential, which was mainly due to the small and dense granular structure effectively hindering the penetration of corrosion media.     

Wear and thermal behavior of basalt fiber reinforced rice husk/polyvinyl chloride composites

Plant fiber reinforced polymer composites (PFRPs) in practical application are often subjected to both complex friction and variable temperature environments. The present work explores the possibility of reinforcing rice husk/polyvinyl chloride (RH/PVC) composites with basalt fibers (BF) for developing a new wear resistant material with improved thermal stability. The results showed that the structural strength and wear resistance of the composites increased at first and then decreased with an increasing ratio of BF/RH, the highest value occurred at a BF/RH ratio of 8/42. The thermal stability of composites had a positive relationship with BF/RH ratio. The composites added with BF all possessed improved performance in comparison with unadded composites. Hence, the findings of this article proposed some new perspectives on improving the wear resistance and thermal stability of PFRPs that would broaden their practical application.     

CrN和CrN/Ag涂层的真空高温摩擦磨损性能*

为改善涂层在真空、高温等苛刻条件下的摩擦学性能，利用中频直流磁控溅射技术在硅片和316L不锈钢上沉积了CrN和CrN/Ag涂层，利用扫描电镜、透射电镜和X射线衍射仪对涂层的成分及相结构进行了表征，通过划痕测试仪、纳米压痕仪和摩擦磨损试验机测试了涂层的力学及摩擦学性能。结果表明：添加Ag元素以后，CrN/Ag涂层硬度及承载能力有所减小，但结合强度增加；真空高温环境下CrN与CrN/Ag涂层摩擦因数随温度升高呈下降趋势，其中CrN涂层通过软化镀层减小剪切强度和阻力，从而减小摩擦因数，CrN/Ag涂层主要通过高温产生的热驱动力诱导表面Ag润滑膜的形成来减小摩擦因数；CrN涂层依靠自身剪切特性参与摩擦，而CrN/Ag涂层在真空高温下具有自润滑和持续润滑性能，作为自润滑零部件具有潜在的应用价值。     

致密砂岩油藏能量补充方式评价及优化

针对致密砂岩油藏大规模体积压裂开发后能量补充困难的问题,利用自主设计制作的大型人造三维岩心物理模型和物理模拟实验舱,开展致密砂岩油藏能量补充方式优化研究。实验结果表明:致密砂岩油藏压裂开发过程中,地层能量损耗严重,采取注水或注气的方式可有效进行能量补充;地层中裂缝规模越大,越有利于原油渗流,后续补充能量的传播范围越广,有助于进一步提高原油采收率;从提高驱油效率和扩大波及系数方面优选吞吐渗吸介质,CO₂均优于活性水,CO₂吞吐开发在矿场试验中取得了显著的增油效果,因此,CO₂吞吐作为一种有效的能量补充方式在致密油开发中展现了良好的应用前景。该文分析了致密砂岩储层水平井压裂开发的渗流规律,优选出致密砂岩储层大规模压裂开发后最佳渗吸介质,可为致密砂岩油藏开发设计提供重要的理论依据。     

Dynamic energy and mass balance model for an industrial alkaline water electrolyzer plant process

This paper proposes a parameter adjustable dynamic mass and energy balance simulation model for an industrial alkaline water electrolyzer plant that enables cost and energy efficiency optimization by means of system dimensioning and control. Thus, the simulation model is based on mathematical models and white box coding, and it uses a practicable number of fixed parameters. Zero-dimensional energy and mass balances of each unit operation of a 3 MW, and 16 bar plant process were solved in MATLAB functions connected via a Simulink environment. Verification of the model was accomplished using an analogous industrial plant of the same power and pressure range having the same operational systems design. The electrochemical, mass flow and thermal behavior of the simulation and the industrial plant were compared to ascertain the accuracy of the model and to enable modification and detailed representation of real case scenarios so that the model is suitable for use in future plant optimization studies. The thermal model dynamically predicted the real case with 98.7 % accuracy. Shunt currents were the main contributor to relative low Faraday efficiency of 86 % at nominal load and steady-state operation and heat loss to ambient from stack was only 2.6 % of the total power loss.     

磨矿动力学研究现状及应用

磨矿动力学是描述被磨物料的磨碎速率与磨矿时间之间关系规律的一种数学模型，对分析物料在磨矿过程中的粒级及能量变化具有重要作用。为充分发挥磨矿动力学在磨矿过程中的作用，论文在分析国内外研究现状的基础上，系统介绍了两种典型的磨矿动力学模型：m阶磨矿动力学模型和磨矿总体平衡动力学模型，分析了模型中各参数的含义；以磨矿总体平衡动力学模型为重点，分析了破碎速率函数和破碎分布函数的求解方式，包括零阶产出率法、奥-勒理论简算法、卡普尔G-H算法以及经验公式法等；从物料性质、磨矿介质及配比、磨矿方式及参数、化学添加剂等几个方面分析了影响磨矿动力学模型的因素；指出了磨矿动力学模型在矿物加工工程领域的应用现状并对其未来的研究方向提出展望。研究表明磨矿动力学在矿物加工领域具有广泛而重要的应用，为进一步改善磨矿工艺提供了理论依据。     

Statistical optimization of operating parameters of microbial electrolysis cell treating dairy industry wastewater using quadratic model to enhance energy generation

The performance of Microbial electrolysis cell (MEC) is affected by several operating conditions. Therefore, in the present study, an optimization study was done to determine the working efficiency of MEC in terms of COD (chemical oxygen demand) removal, hydrogen and current generation. Optimization was carried out using a quadratic mathematical model of response surface methodology (RSM). Thirteen sets of experimental runs were performed to optimize the applied voltage and hydraulic retention time (HRT) of single chambered batch fed MEC operated with dairy industry wastewater. The operating conditions (i.e) an applied voltage of 0.8 V and HRT of 2 days that showed a maximum COD removal response was chosen for further studies. The MEC operated at optimized condition (HRT- 2 days and applied voltage- 0.8 V) showed a COD removal efficiency of 95 ± 2%, hydrogen generation of 32 ± 5 mL/L/d, Power density of 152 mW/cm² and current generation of 19 mA. The results of the study implied that RSM, with its high degree of accuracy can be a reliable tool for optimizing the process of wastewater treatment. Also, dairy industry wastewater can be considered to be a potential source to generate hydrogen and energy through MEC at short HRT.     

Optimization of PEMFC system operating conditions based on neural network and PSO to achieve the best system performance

PEMFC system is a complex new clean power system. Based on MATLAB/Simulink, this paper develops a system-level dynamic model of PEMFC, including the gas supply system, hydrogen supply system, hydrothermal management system, and electric stack. The neural network fits the electric stack model to the simulation data. The effects of different operating conditions on the PEMFC stack power and system efficiency are analyzed. Combining the power of the reactor and the system efficiency to define the integrated performance index, the particle swarm optimization (PSO) algorithm is introduced to optimize the power density and system efficiency of the PEMFC with multiple objectives. The final optimal operating point increases the power density and system efficiency by 1.33% and 12.8%, respectively, which maximizes the output performance and reduces the parasitic power.     

Hydrogen-rich gas generation via the exhaust gas-fuel reformer for the marine LNG engine

Reformed exhaust gas recirculation technology has attracted great attention in internal combustion engines. A platform of an exhaust gas-fuel reformer connected with the marine LNG engine was set up for generating on-board hydrogen. Based on the platform, effects of the methane to oxygen ratio (M/O) and reformed exhaust gas ratio (R_EG) from the reformer and excess air ratio (λ) from the engine on the components, hydrogen yield, thermal efficiency and reforming process of the reformer were experimentally investigated. Results shown that hydrogen-rich gases (reformate) can be generated by reforming the mixture of engine exhaust gas (about 400 °C) and methane supplied via the reformer with Ni/Al₂O₃ catalyst, and the hydrogen concentration of reformate was between 6.2% and 12.6% by volume. The methane supplied rate and λ affected the components and temperature of the reactant in the reformer, while R_EG changed the gas hour space velocity during the exhaust gas-fuel reforming processes, resulting in the difference in the components of the reformate and thermal efficiency. At the present experimental condition, the highest H₂ concentration reformate was generated under the M/O of 2.0, λ of 1.55 and R_EG of 6%.