Life cycle assessment of HFC-134a production by calcium carbide acetylene route in China

HFC-134a is a widely used environment-friendly refrigerant. At present, China is the largest producer of HFC-134a in the world. The production of HFC-134a in China mainly adopts the calcium carbide acetylene route. However, the production route has high resource and energy consumption and large waste emission, and few of the studies addressed on the environmental performance of its production process. This study quantified the environmental performance of HFC-134a production by calcium carbide route via carrying out a life cycle assessment (LCA) using the CML 2001 method. And uncertainty analysis by Monte-Carlo simulation was also carried out. The results showed that electricity had the most impact on the environment, followed by steam, hydrogen fluoride and chlorine, and the impact of direct CO₂ emissions in calcium carbide production stage on the global warming effect also could not be ignored. Therefore, the clean energy (e.g., wind, solar, biomass, and natural gas) was used to replace coal-based electricity and coal-fired steam in this study, showing considerable environmental benefits. At the same time, the use of advanced production technologies could also improve environmental benefits, and the environmental impact of the global warming category could be reduced by 4.1% via using CO₂ capture and purification technology. The Chinese database of HFC-134a production established in this study provides convenience for the relevant study of scholars. For the production of HFC-134a, this study helps to better identify the specific environmental hotspots and proposes useful ways to improve the environmental benefits.     

一种新型的室温快速固化胶黏剂的研制

本文开发了一种新型的方舱夹芯板用室温固化高强度环氧结构胶黏剂,验证了其物化特性、相关力学性能和环境适应性。结果表明此胶黏剂具有优良性能,可以满足方舱用大板胶黏剂的使用需求。     

Synthesis,microstructures, and corrosion behaviors of multi-components rare-earth silicates

Multi-components and equimolar rare earth monosilicates, (Y_1/3Dy_1/3Er_1/3)₂SiO₅, (Y_1/3Dy_1/3Lu_1/3)₂SiO₅, (Y_1/4Dy_1/4Ho_1/4Er_1/4)₂SiO₅ and (Yb_1/4Dy_1/4Ho_1/4Er_1/4)₂SiO₅, were prepared by solid-state reactions and the following hot-pressing. Dense microstructures with uniform elemental distributions were obtained for all samples. These investigated multi-components monosilicates exhibit low thermal conductivities and similar coefficients of thermal expansion with SiC. Moreover, they exhibit high corrosion resistances in 1400 °C water vapor, especially, four-components (Y_1/4Dy_1/4Ho_1/4Er_1/4)₂SiO₅ and (Yb_1/4Dy_1/4Ho_1/4Er_1/4)₂SiO₅ experienced almost invariable weights after small weight losses during the initial 0.5 h. All those results indicate that multi-components rare earth monosilicates are promising candidates of environmental barrier coatings for SiC/SiC composites.     

Drivers of revitalization in Great Lakes coastal communities

Sediment remediation and habitat restoration projects have been increasingly employed along the coast of the Great Lakes to improve environmental quality since the designation of 43 highly degraded Areas of Concern (AOCs) by the 1987 Great Lakes Water Quality Agreement between the U.S. and Canada. Improvements in water quality, habitat, and other environmental conditions can also support community wellbeing and revitalization; however, the mechanisms that support these connections are relatively unclear. We address this gap through a case study of three AOCs near Lake Michigan: 1) Grand Calumet River; 2) White Lake, and 3) Muskegon Lake. By analyzing secondary data and planning documents, we found that alongside environmental cleanup, anchor institutions, housing and economic development, and local events drive revitalization. Our research also illustrates that, rather than acting as discrete processes, environmental cleanup and revitalization drivers overlap in time and space. Finally, our research reveals a high level of variation within and across AOCs in terms of diverse socioeconomic contexts, planning capacities, and existing partnerships. Together, our findings point to the need for collaborative and inclusive planning processes that account for the heterogeneity present within and across AOCs to simultaneously support remediation, restoration, and revitalization and to sustain continued revitalization in AOC communities after delisting.     

Water vapor volatilization and oxidation induced surface cracking of environmental barrier coating systems: A numerical approach

A numerical model is developed for surface crack propagation in brittle ceramic coatings, aiming at the intrinsic failure of rare-earth silicate environmental barrier coating systems (EBCs) under combustion conditions in advanced gas turbines. The main features of progressive degradation of EBCs in such conditions are captured, including selective silica vaporization in the top coat due to exposure to water vapor, diffusion path-dependent bond coat oxidation, as well as crack propagation during cyclic thermal loading. In light of these features, user-defined subroutines are implemented in finite element analysis, where surface crack growth is simulated by node separation. Numerical results are validated by existing experimental data, in terms of monosilicate layer thickening, thermal oxide growth, and fracture behaviors. The experimentally observed quasi-linear oxidation in the early stage is also elucidated. Furthermore, it is suggested that surface crack undergoes rapid propagation in the late stage of extended thermal cycling in water vapor and leads to catastrophic failure, driven by both thermal mismatch and oxide growth stresses. The latter is identified as the dominant mechanism of penetration. Based on detailed analyses of failure mechanisms, the optimization strategy of EBCs composition is proposed, balancing the trade-off between mechanical compliance and erosion resistance.     

Crack-healing behaviour of MoSi2 dispersed Yb2Si2O7 environmental barrier coatings

MoSi₂ doped Yb₂Si₂O₇ composites were designed to extend the lifetime of Yb₂Si₂O₇ environmental barrier coatings (EBCs) via self-healing cracks during high-temperature applications. Yb₂Si₂O₇–Yb₂SiO₅–MoSi₂ composites with different mass fractions were prepared by applying spark plasma sintering. X-ray diffraction results confirmed that the composites consisted of Yb₂Si₂O₇, Yb₂SiO₅, and MoSi₂. The thermal expansion coefficients (CTEs) of the composites increased with an increase in the MoSi₂ content. The average CTE of the 15 wt% MoSi₂ doped Yb₂Si₂O₇ composite was 5.24 × 10^?6 K^?1, indicating that it still meets the CTE requirement of EBC materials. After being pre-cracked by using the Vickers indentation technique, the samples were annealed for 0.5 h at 1100 or 1300 °C to evaluate the crack-healing ability. Microstructural studies showed that cracks in 15 wt% MoSi₂ doped Yb₂Si₂O₇ composites were fully healed during annealing at 1300 °C. Two mechanisms may be responsible for crack healing. First, the cracks were filled with SiO₂ glass formed by MoSi₂ oxidation. Second, the formed SiO₂ continued to react with Yb₂SiO₅ to form Yb₂Si₂O₇, which can cause cracks to heal owing to volumetric expansion. The Yb₂Si₂O₇ formation with smaller volume expansion is more beneficial.     

High-temperature water-vapor reaction mechanism of barium strontium aluminosilicate (BSAS)

Environmental barrier coatings (EBCs) are used in commercial turbine engine applications as protection for ceramic matrix composites, yet the high-temperature water vapor reaction mechanism for EBC materials is not fully understood. Here, the water vapor reaction mechanism for barium strontium alumino-silicate (BSAS), an early generation EBC candidate, was determined from the time and temperature dependences of material loss. BSAS water vapor exposures were performed at 1200 °C, 1300 °C, and 1400 °C for 24, 48, and 72 h, at maximum gas velocities of ~ 240 m/s. FactSage thermodynamic calculations were shown to support the experimental findings, where the steam reaction mechanism consisted of volatilization of all BSAS oxide constituents as gaseous metal hydroxide species, i.e. Ba(OH)₂, Sr(OH)₂, Al(OH)₃, and Si(OH)₄ (g).     

环境设计专业学习空间设计探析--以教室改造的参与式设计为例

学习空间的设计必须基于教育理念、学习模式、技术设施与精神氛围等因素展开,以更开放、灵活及多样化的有趣形态来吸引使用者。对于已掌握基本设计方法并具有一定设计思维的环境设计专业学生而言,设计与自身学习行为关联的学习空间,能体现"参与式设计"的特殊意义:即一方面以有着直观体验感受的熟悉空间作为训练案例来有效地整合设计能力;另一方面则通过用户与设计者身份的叠加,从使用者体验一维到对空间发展的专业预设考虑一维共同实现学习空间设计理念的更新。     

Long-term performance of a HDPE geomembrane stabilized with HALS in chlorinated water

A high density polyethylene geomembrane (GMB) stabilized with hindered amine (light) stabilizers (HALS or HAS) is immersed in four chlorinated water solutions with a simulated free chlorine concentration range of 0.5–5 ppm at five different temperatures (25, 40, 65, 75, and 85 °C) for 70 months. Standard and high pressure oxidative induction time (OIT) tests are performed to monitor antioxidants depletion while melt flow index, tensile, and stress crack resistance (SCR) tests are conducted to monitor degradation in physical and mechanical properties. Degradation in the GMB properties occurred shortly after immersion in chlorinated water at all temperatures except at 25 °C. Increasing the free chlorine concentration resulted in faster degradation of the tensile properties and SCR. The predicted time to nominal failure based on SCR ranges between 25 years at 40 °C and 5 years at 85 °C in chlorinated water (with 0.5 ppm free chlorine). A comparison between the degradation in SCR of this GMB and a GMB with a different resin and without HALS shows significant difference in their performance in chlorinated water but not in other incubation media.