建筑工业化发展的多群体演化博弈与仿真研究

新型建筑工业化具有高质量、低消耗、可循环发展等特征，其推广已上升到国家战略层面。利用演化博弈方法，建立“政府-开发商-银行” 的三方动态演化博弈模型，进行各博弈主体策略的演化稳定性分析，并针对初始状态、奖惩力度、借贷风险和开发成本等对演化结果的影响进行动态仿真。在此基础上， 考虑开发商群体的网络拓扑特征对演化真实性的影响，引入复杂网络理论， 以无标度网络为载体描述开发商个体的连接偏好和决策机制，构建政府监管下的建筑工业化扩散模型，并通过仿真深入研究相关因素对扩散深度的影响作用，最后结合仿真结果给出相应对策建议。     

立柱加固型框架大楼的爆破拆除

采用定向控制爆破技术拆除立柱加固型7层框架大楼。为了彻底炸毁加固立柱,确保大楼顺利定向倾倒,通过多次爆破试验确定了炸药单耗、布孔参数和装药结构。为了控制大楼塌落时的触地震动,采取了秒差分区爆破、空中解体、铺垫缓冲层和开挖减震沟等技术措施。爆破过程中进行了震动监测。此外还介绍了起爆顺序、安全防护措施及爆破结果。     

内含实体对H型垂直轴风力机气动性能的影响

以H型垂直轴风力机及其内含圆柱形实体为研究对象,对NACA0018翼型的五叶片H型垂直轴风力机的气动性能进行数值模拟和实验验证。分析8种不同直径的内含圆柱体,在内含实体截面积占风轮迎风面积之比分别为21.2%、50.0%和76.9%时,风力机风能利用率的峰值分别下降8.04%、20.7%及74.3%。结果表明：随着内含实体直径的增大,风能利用率的峰值逐渐减小,开始较为缓慢,达到一定值时快速下降。小直径内含实体主要影响叶片在下风区的转矩,对风能利用率的影响较小,而大直径内含实体还会影响叶片在上风区的转矩,其风能利用率迅速减小。对于内含固定直径的实体,比如在现有建筑物外侧安装风力机时,其风轮半径的选择需综合考虑风能利用率和风力机的建造成本两方面的因素。研究结果可为建筑物与垂直轴风力机进行有效结合以提高风能的利用提供参考。     

Dynamic simulation of hydrogen-based off-grid zero energy buildings with hydrogen storage considering Fanger model thermal comfort

In this study, some locations with different climates, off-grid zero energy buildings with hydrogen energy storage systems are designed, and transient analysis is conducted. These considered buildings supply their electricity consumption without using the electrical grid and PV panels or wind turbines. Also, they supply thermal comfort to occupants by using a vapor compression chiller and humidifier. Domestic hot water of occupants is supplied using solar collectors. For analyzing building's performance and objectives achievement, TRNSYS software is used. Also, for evaluating occupant thermal comfort, the Fanger model is used. The considered building is a one-story building with a 150 m² area. Four occupants are considered. Both of them are seated at rest, and another is seated with light working such as typing. Using the Fanger model equation and MATLAB software, the thermal comfort of occupants is determined. For domestic hot water consumption, verified profiles that vary during 24 h of the day are considered. Achieved results show that for humid and cold cities, PV panels with an area of 73 and 76 m² can be supplied the required electricity of considered building with four occupants and battery state of charge is higher than 50% and 10%, respectively. Moreover, with a suitable air conditioner system, the predicted percentage of dissatisfied (PPD) can be lower than 12% and 8% for humid and cold cities. Therefore, the building can be converted to a zero-energy building using its rooftop area.     

箱形横梁的水压爆破拆除

某电影院大厅内钢筋混凝土箱形横梁长25m,断面尺寸1 6m×2 4m,用水压爆破拆除。通过梁的受力分析得知,为避免横梁的挠度过大,在吊梁拆除后必须另补支撑,以确保水压爆破正常进行。文中对水压爆破炸药用量的计算公式进行了比较和简评。在参考计算结果和考虑厅内环境的基础上,并结合以往水压爆破工程的经验,确定了合理、有效的药量,保证了主体结构的绝对安全。     

SRS: Spatial-tagged radio-mapping system combining LiDAR and mobile-phone data for indoor location-based services

One of the most challenging issues in radio received signal strength (RSS)-based localization systems is the generation and distribution of a radio map with a coordinate system linked with spatial information in a large indoor space. This study proposes a novel spatial-tagged radio-mapping system (SRS) that effectively combines the heterogeneous properties of LiDAR and mobile phones to simultaneously perform both spatial and radio mappings. The SRS consists of synchronization, localization, and map building processes, and enables real-time spatial and radio mapping. In the synchronization process, the distance range, motion data, and radio signals obtained through the LiDAR and mobile phone are collected in nodal units according to the sensing time. In the localization process, a feature variance filter is used to control the number of features generated from LiDAR and estimate the positions at which the nodes are generated in real time according to the motion data and radio signals. In map building, the estimated positions of the nodes are used to extract spatial and radio maps by using a unified location coordinate system. To ensure mobility, the SRS is manufactured in the form of a backpack supporting LiDAR and a mobile phone; the usefulness of the system is experimentally verified. The experiments are performed in a large indoor shopping mall with a complex structure. The experimental results demonstrated that a common coordinate system could be used to build spatial and radio maps with high accuracy and efficiency in real time. In addition, the field applicability of the SRS to location-based services is experimentally verified by applying the constructed radio map to well-known fingerprinting algorithms using the heterogeneous mobile phones.     

Estimating long-term time-resolved indoor PM2.5 of outdoor and indoor origin using easily obtainable inputs

To evaluate the separate impacts on human health and establish effective control strategies, it is crucial to estimate the contribution of outdoor infiltration and indoor emission to indoor PM_2.5 in buildings. This study used an algorithm to automatically estimate the long-term time-resolved indoor PM_2.5 of outdoor and indoor origin in real apartments with natural ventilation. The inputs for the algorithm were only the time-resolved indoor/outdoor PM_2.5 concentrations and occupants’ window actions, which were easily obtained from the low-cost sensors. This study first applied the algorithm in an apartment in Tianjin, China. The indoor/outdoor contribution to the gross indoor exposure and time-resolved infiltration factor were automatically estimated using the algorithm. The influence of outdoor PM_2.5 data source and algorithm parameters on the estimated results was analyzed. The algorithm was then applied in four other apartments located in Chongqing, Shenyang, Xi'an, and Urumqi to further demonstrate its feasibility. The results provided indirect evidence, such as the plausible explanations for seasonal and spatial variation, to partially support the success of the algorithm used in real apartments. Through the analysis, this study also identified several further development directions to facilitate the practical applications of the algorithm, such as robust long-term outdoor PM_2.5 monitoring using low-cost light-scattering sensors.     

玻璃棉/SiO2气凝胶复合板的改性研究

通过选取无水乙醇为溶剂，以SiO₂气凝胶为溶质，制备SiO₂气凝胶改性溶液，并将其应用于改善玻璃棉的保温性能。通过浸润及常压干燥的方法制取玻璃棉/SiO₂气凝胶复合板，研究SiO₂气凝胶的质量分数和浸润时间对其性能的影响，并与溶胶-凝胶法制备的玻璃棉/SiO₂气凝胶复合板相比。研究表明SiO₂气凝胶的质量分数和浸润时间对玻璃棉/SiO₂气凝胶复合板的性能有显著影响。当SiO₂气凝胶质量分数达到8%且浸润时间为20 min时，玻璃棉/SiO₂气凝胶复合板的短期吸水率、热导率分别下降了38.09%、18.32%，抗压强度上升了102.89%。与溶胶-凝胶法相比，本方法具有制备周期短、工艺较为简洁、成本低等优点，更适宜于大规模生产应用。     

The home environment in a nationwide sample of multi-family buildings in Sweden: associations with ocular,nasal, throat and dermal symptoms,headache, and fatigue among adults

Risk factors at home for ocular, nasal, throat and dermal symptoms, headache, and fatigue were studied in a nationwide questionnaire survey in Sweden, the BETSI study in 2006. Totally, 5775 adults from a stratified random sample of multi-family buildings participated. Associations between home environment factors and weekly symptoms were analyzed by multi-level logistic regression. In total, 8.3% had ocular symptoms; 11.9% nasal symptoms; 7.1% throat symptoms; 11.9% dermal symptoms; 8.5% headache and 23.1% fatigue. Subjects in colder climate zones had more mucosal and throat symptoms but less fatigue and ocular symptoms. Rented apartments had poorer indoor environment than self-owned apartments. Those living in buildings constructed from 1961 to 1985 had most symptoms. Building dampness, mold and mold odor were risk factors, especially headache and ocular symptoms. Lack of mechanical ventilation system was another risk factor, especially for headache. Environmental tobacco smoke (ETS), electric radiators, and crowdedness were other risk factors. Oiled wooden floors, recent indoor painting, and new floor materials were negatively associated with symptoms. In conclusion, building dampness, mold, poor ventilation conditions, crowdedness, ETS, and emissions from electric radiators in apartments in Sweden can increase the risk of ocular, nasal, throat and dermal symptoms, headache, and fatigue.     

基于虚拟格网的建筑物点云轮廓线自动提取

在分析现有轮廓线提取方法不足的基础上，提出基于虚拟格网的建筑物轮廓线自动提取方法。该方法利用建筑物点云生成虚拟格网并进行二值填充；采用邻域分析方法进行边界格网的标记与追踪；为了避免边界追踪错误，设计了基于方向的单边缘格网抑制方法及基于距离的连接关系调整方法以改善提取结果质量；根据格网追踪结果，从原始建筑物点云中提取真实轮廓点以保持原始建筑物轮廓形态；采用随机抽样一致性估计及最小二乘拟合方法进行轮廓线规则化处理，实现建筑物轮廓线的自动提取。实验结果表明，该方法能快速从建筑物点云中提取轮廓线，可为建筑物轮廓线的自动提取提供一种可行的解决方案。