Modelling dislocation assisted tempering during rolling contact fatigue in bearing steels

Rolling contact fatigue in bearing steels is manifested by dark-etching regions, which are attributed to deformation induced tempering. In order to quantitatively explain this phenomenon, a model is suggested for martensite tempering assisted by dislocation glide during rolling contact fatigue. In the model, dislocations transport carbon from the matrix to carbide particles, provided that the carbon is located at a certain distance range from the dislocation contributing to the tempering process. By calculating the amount of carbon in the matrix, the kinetics of carbide thickening and hardness reduction are computed. It is found that the dark-etching region kinetics can be controlled by both bearing operation conditions (temperature and deformation rate) and microstructure (type, size, and volume fraction of carbides). The model is validated against tested bearings, and its limitations are discussed.     

Damage mechanism at different transpassive potentials of solution-annealed 316 and 316l stainless steels

Electrochemical impedance spectroscopy (EIS), anodic polarization and scanning electron microscopy techniques were used to investigate the damage mechanism in the transpassive potential region of AISI ...     

面积坐标法构造含转角自由度的四结点膜元

以四边形面积坐标作为工具,构造了两个含转角自由度的广义协调四边形单元AQ4和lAQ4。它们通过强式分片检验,与同类单元相比,具有很高的计算精度,能消除梯形闭锁现象,有很强的抗网格畸变的能力。     

Progressive damage modelling of SMC composite materials

The present work deals with the modelling of damage behaviour for sheet moulding compound (SMC) composite materials using a finite element analysis package. Specifically, a comparison is made between the results obtained experimentally for a three-point bending test, and those obtained from numerical simulation using a material model already implemented. The simulation has been performed for the material models available within the PAM-CRASH software. The simulation results are compared and validated with respect to experimentation.     

小井距开发现河油田低渗油藏可行性研究

认为注采井网井距大,水驱控制程度差,采收率偏低是影响胜利油田现河低渗透油藏开发的关键,通过井间密度与水驱控制程度和采收率的关系等分析,提出了现河低渗透油藏开发的合理的井网密度。     

高抗挤厚壁套管的性能及应用效果评价

中原油田套管损坏的主要原因是现有套管强度不够,无法抵抗盐膏层段的巨大外挤力。开发了TP130TT型高抗挤厚壁套管,其强度能很好地抵抗盐膏层巨大外挤力。实验室试验表明,各项性能指标达到了设计要求,现场使用取得了很好的效果,解决了中原油田盐膏层段套管强度不足的难题。     

掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

低密度微泡沫压井液的研究与应用

吐哈油田部分区块地层压力系数小于0.9,常规水基压井液对储层伤害大,若使用油基压井液成本高,环境污染严重。通过实验优选出了一种低密度水基微泡沫压井液。该压井液具有密度低、泡沫强度高、稳定性好、携砂能力强等优点。现场应用表明,低密度微泡沫压井液稳定时间大于48 h,密度在0.70~0.99 g/cm3之间可调,抗油污染能力强,抗油大于8%,抗温在100℃以上,岩心污染后渗透率恢复值大于80%;并且施工方便,成本低,具有储层保护能力,使用微泡沫压井液的井表皮系数在0.20~2.34之间。     

饼干炉湿度控制的改进方法

在大空间的温度控制系统中 ,采用简单的PID控制规律 ,对空间的温度、湿度进行解藕计算 ,将空间的相对湿度控制转化为送风含湿量的控制。该控制方式稳定、可靠 ,并且节约能源。本方法适用于所有的烘烤炉中     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.