Performance characteristics of concrete based on a ternary calcium sulfoaluminate–anhydrite–fly ash cement

This paper reports an assessment of the performance of concrete based on a calcium sulfoaluminate–anhydrite–fly ash cement combination. Concretes were prepared at three different w/c ratios and the properties were compared to those of Portland cement and blast-furnace cement concretes. The assessment involved determination of mechanical and durability properties. The results suggest that an advantageous synergistic effect between and ettringite and fly ash (Ioannou et al., 2014) was reflected in the concrete’s low water absorption rates, high sulfate resistance, and low chloride diffusion coefficients. However, carbonation depths, considering the dense ettringite-rich microstructure developed, were higher than those observed in Portland cement concretes at a given w/c ratio. It was concluded that the amount of alkali hydroxides present in the pore solution is as important factor as the w/c ratio when performance of this type of concrete is addressed.     

Verhalten von Magnesiumlegierungen für Anwendungen im Fahrzeugbau bei mechanisch‐elektrochemischer Komplexbeanspruchung: Einfluss passivierender Deckschichten und Mechanismen der lokalen Schädigung

Behavior of Magnesium‐Alloys for Automotive Applications under Mechanical and Environmental Loading: Influence of Passivating Films and Mechanisms of Local Breakdown To assure an efficient design of components under cyclic loading, all available data concerning fatigue have to be observed. Therefore the influences of manufacturing on the material condition, the mechanical loads and environmental effects have to be analysed. Magnesium‐alloys are of special interest for lightweight applications because of their excellent strength‐density ratio. The corrosion resistance of magnesium‐alloys depends on the same factors that are critical to other metals. The alloys have a good stability to atmospheric exposure and a good resistance to attack by alkali, chromic and hydrofluoric acids. However, because of the electrochemical activity of magnesium, the relative importance of some factors is greatly amplified. The nature and composition of passive films formed on magnesium‐alloys depend on the prevailing conditions, viz. alloy‐composition, passivation potential, pH, electrolyte composition and temperature. Passive films may be damaged by local breakdown. Because of this, magnesium‐alloys suffer a degradation of their properties when exposed to an aqueous environment. The main topic of the present investigations is the verification of mechanisms of the local breakdown of the protecting film. At least two mechanisms are possible for this localization: mechanical breakdown by slip steps and electrochemical breakdown (for e.g. by the effects of chloride ions). Corrosion and passivation of different high purity alloys have been studied in different solutions (neutral, alkaline with specific anions and cations) using electrochemical techniques. The diecasted alloys were tested as produced and machined. The results clarified that depending on alloy/material and surface condition/corrosion environment different mechanisms for electrochemical breakdown of the protecting films are possible. Hence fatigue life under environmental loading is influenced by surface and testing conditions.     

草酸钙在硫酸软骨素自组装膜上周期沉淀的研究

利用硫酸软骨素(chondroitin sulfate，CS)在云母基底上通过浇铸法制备的自组装膜为基底，诱导草酸钙在其上的凝集生长。发现当硫酸软骨素的浓度为1．Omg／ml时在该膜体系中可形成规整的周期性草酸钙环状沉淀。这种有序的环状结构可能是耗散结构的一种具体表现形式。利用原子力显微镜(atomic forcemicroscope，AFM)和傅立叶红外光谱仪对这种结构进行了表征，实验结果显示合适浓度下形成的CS膜在一定程度上可以抑制草酸钙的凝集结晶，表明高分子基质与无机离子间强烈的相互作用对无机盐的成核结晶有显著影响，为探讨结石的形成与抑制提供了一定的实验依据。     

石膏转化制硫酸钾结晶动力学及结晶添加剂研究

研究了浓氨介质中石膏与氯化钾直接转化制硫酸钾的结晶动力学及结晶添加剂的作用效果。结果表明 ,硫酸钾在氨介质中的成核速率与晶体生长速率、悬浮密度、搅拌速率存在如下关联式 :B0 =5 .64 13×10 8G3.32 0 8Mt0 .0 559np0 .2 92 8。加入异丙醇、OP乳化剂及十二烷基苯磺酸钠等添加剂 ,可使硫酸钾结晶产品纯度提高 ,晶体形态整齐均匀     

Ca掺杂钨镁酸铅陶瓷材料的制备及其介电性能

研究了Ca掺杂钨镁酸铅(PMW)陶瓷材料的合成、结构、烧结以及介电性能。结果发现：在Ca^2 摩尔分数小于15％时，能形成单相的PCMW钙铁矿相，结构由原来的斜方相向立方相转变。用二步合成法制备的样品容易致密烧结，气孔率比一步法制备的样品小。Ca的加入降低了材料的介电损耗，在频率为1MHz时，介质损耗达到了10^-4。当Ca^2 摩尔分数大于10％时，材料的Curie峰宽化显著，介电常数温度系数降低。     

醇镁还原法一步制取对氯苯胺的研究

醇镁还原法一步制取对氯苯胺是一种新的方法 ,研究发现最佳反应温度为 80℃～ 85℃ ,反应时间为4h ,对氯硝基苯与镁粉的用量 (物质的量比 )为 1∶3,产率为 80 %。     

MB8镁合金薄板的搅拌摩擦焊

针对我国航空航天工业常用的MB8镁合金。采用搅拌摩擦焊工艺进行焊接，对其焊缝的成形特点、组织特征和力学性能进行分析。结果表明，采用搅拌摩擦焊焊接镁合金效果良好。     

十二酰胺丙基二甲基羟乙基氯化铵与十二烷基硫酸钠水溶液的表面吸附和胶束形成

利用十二酰胺丙基二甲胺和氯乙醇反应 ,合成了十二酰胺丙基二甲基羟乙基氯化铵 (DDHA)阳离子表面活性剂 ,将其与十二烷基硫酸钠 (SDS)以不同摩尔比进行混合 ,测定了混合系统的表面张力 ,计算了单一系统和混合系统的饱和吸附量、分子最小截面积 ,表面层和胶束中 DDHA的摩尔分率及分子间相互作用参数 ,目视观察了混合系统的浑浊情况。结果表明 :在降低γcmc和 cmc方面 ,DDHA SDS混合系统有协同效应 ,表面层和胶束的组成与二组分配比有关 ,但是非对称的 ,等物质的量混合物中 ,DDHA在胶束和表面层中具有较大的摩尔分数。DDHA与 SDS在实验测定的各混合系统中都不出现混浊     

用硫酸铁铵容量法测定钛精矿中二氧化钛含量

样品在过氧化钠熔融、水浸取及盐酸酸化后，在盐酸和硫酸介质中，隔绝空气，用金属铝将钛(Ⅳ)还原至钛(Ⅲ)，以硫氰酸盐为指示剂，用硫酸铁铵标准溶液滴定。     

Immobilization and activation of vanadium(III) and titanium(III) single‐site catalysts for ethylene polymerization using MgCl2‐based supports

Significant increases in the activity of vanadium(III) amidinate catalysts for ethylene polymerization have been obtained by immobilization on a MgCl₂‐based support prepared by reaction of AlEt₃ with a MgCl₂/ethanol adduct. Catalyst immobilization and activation on this type of support prevents the rapid decay in activity observed under homogeneous polymerization conditions with unsupported catalysts. Stable polymerization activity is also observed with analogous titanium(III) complexes. Polyethylene with narrow molecular weight distribution and spherical particle morphology is obtained without reactor fouling. Copyright © 2005 Society of Chemical Industry