Effect of the cultivation mode on red pigments production from Monascus ruber

In submerged cultures performed in chemically defined fermentation medium containing glucose and glutamate, the growth and production of water‐soluble red pigments and citrinin by the filamentous fungus Monascus ruber were studied under various carbon/nitrogen (C/N) ratios. The specific production of the red pigments was optimal at a glucose/glutamate ratio of about 10 and then steadily decreased at higher C/N ratio. In contrast, the production of the mycotoxin increased with increased C/N with an optimum in the range of 30–45. In a fed‐batch mode, it was also found that the production of pigments was not favoured in fed‐batch mode by feeding the medium with glucose while keeping the C/N ratio lower than 10. This low production likely resulted from concurrent high accumulation of L‐malic acid that was reported to inhibit this production. In contrast, this mode of cultivation was rather favourable for the production of the mycotoxin.     

Application of the methylene blue test to cement raw materials

Characterisation of raw materials for Portland cement manufacture by use of the methylene blue adsorption method is discussed. The method is shown to be a simple, convenient ‘rule of thumb’ procedure. It provides a guide to the quantity and type of argillaceous minerals present in a given raw material sample.     

Poly(butylene terephthalate)–clay nanocomposites prepared by melt intercalation: morphology and thermomechanical properties

Nanocomposites based on poly(butylene terephthalate) (PBT) and an organoclay (Cloisite 30B) were prepared by melt blending using a twin‐screw extruder. Two kinds of PBTs, ie PBT‐A and PBT‐B, with different inherent viscosities (η_inh), were used for this study (η_inh of PBT‐A and PBT‐B were 0.74 and 1.48, respectively). Dispersion of the clay layers in the PBT nanocomposites was characterized by using X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Tensile and dynamic mechanical properties and non‐isothermal crystallization temperatures of the nanocomposites were also examined. Nanocomposites based on the higher‐viscosity PBT (PBT‐B) showed a higher degree of exfoliation of the clay and a higher reinforcing effect when compared to the composites based on the lower‐viscosity PBT (PBT‐A). The clay nanolayers dispersed in PBT matrices lead to increases in the non‐isothermal crystallization temperatures of the PBTs, with such increases being more significant for the PBT‐B nanocomposites than for the PBT‐A nanoocomposites. Copyright © 2004 Society of Chemical Industry     

Effective factors on synthesis of the hematite–silica red inclusion pigment

The work focuses on the synthesis of a red ceramic pigment by inclusion of hematite in a fumed silica matrix with different specific surface areas. Iron(II) sulfate was used as hematite precursor. Mixtures of iron(II) sulfate and fumed silica with different mole ratios were heated at different temperatures from 1000 to 1300 °C for 4 h.     

Integrating psychology and politics.

Comments on the article "A house divided? The psychology of red and blue America" by D. C. Seyle and M. L. Newman (see record 2006-11202-001). Seyle and Newman concluded that the red and blue metaphor is inaccurate and proposed a purple America strategy to better convey that the majority of people do not align themselves with political extremes. There is interdisciplinary agreement on this. Although not cited by Seyle and Newman, the findings by Professor Fiorina of Stanford University were reported by the APA Monitor on Psychology in its coverage of the 2005 APA State Leadership Conference (Murray Law, 2005). In contrast to their social psychological analysis, Seyle and Newman were incorrect in concluding that "[a]s psychologists, we are not in a position to change either the elements of the American political system that may spur this conflict or even the decisions made by pundits, politicians, and reporters about the terms they choose to use in political discussion" (p. 579). (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Electrochemical Aspects of Electroosmotic Dewatering of Clay Suspensions

An attempt is made to elucidate the electrochemical aspects of the electroosmotic dewatering (EOD) of clays as reported in some recent work, especially that on interrupted DC power electroosmotic dewatering published by Rabie, Mujumdar and Weber (2). These authors showed that the dewatering by EOD stops after the DC power has been on for several minutes or hours; on interruption of their power and on short-circuiting of the electrodes, conditions can be created again for some further dewatering by DC power EOD. This discovery, of Rabie et al. is interpreted as a fuel cell effect and it is shown that it affords clues to several other electrochemical strategies for the possible enhancement of the efficiency of the EOD by DC power.

Further, the open circuit potentials observed by Rabie et al. (2) on the interruption of DC power are given an electrochemical interpretation which leads to quantitative estimates in agreement with the experimental values.     

Ultrasound‐activated Knoevenagel condensation of malononitrile with carbonylic compounds catalysed by alkaline‐doped saponites

α,β‐Unsaturated nitriles have been synthesized by Knoevenagel condensation of a carbonylic compound with malononitrile, assisted by sonochemical irradiation. Two alkaline‐promoted clays (Li⁺‐ and Cs⁺‐exchanged saponites) have been employed as catalysts. The influence of the carbonylic compound (benzaldehyde or cyclohexanone) and the use of a solvent on the catalytic activity have been studied. Remarkable increase in the conversion values has been found when the reaction is activated by ultrasound, as compared with the thermal activation. In this green, solvent‐free procedure, α,β‐unsaturated nitriles have been produced in very high yields (97%) when the Cs⁺‐saponite is used as catalyst. Copyright © 2004 Society of Chemical Industry     

铁水鱼雷罐的检测方案研究

论文介绍了一种针对铁水鱼雷罐车铁水液位检测的较为可行的低成本方案。采用车上间接称重、远红外非接触传输信号方式，解决了对移动铁水罐车进行实时监测的难题。     

Metal sorption by biomass of melanin‐producing fungi grown in clay‐containing medium

The sorption of toxic metals by fungal mycelia grown in clay‐containing medium is reported in this work. Biomass of melanin‐producing microfungi of the genus Cladosporium (C cladosporioides, C resinae and C herbarum) and Aureobasidium pullulans, clay minerals and fungal mycelia grown in clay‐containing medium were compared for their equilibrium Cu and Cd uptake from pH‐buffered solutions using experimental sorption isotherms. Bentonite (Cherkassy) in the natural form was shown to be the best Cu sorbent compared with the other clays and clay minerals tested. Cu sorption isotherms fitted the Langmuir sorption model for all cases. Comparison of Cu and Cd uptake for biomass and bentonite showed a lower biomass uptake capacity but a considerably higher affinity of the biosorbent for the solute. The presence of kaolinite and palygorskite in the medium generally reduced both Cu and Cd sorption capacity and the metal‐binding ability of the fungal–clay mixtures. In contrast, addition of bentonite into the medium did not appreciably alter the Cd sorption ability but increased the sorption of Cu by A pullulans and C cladosporioides grown in this medium. A common feature for all fungi grown in the presence of bentonite was an increase in the Cu sorption capacity (Q_max) of the biomineral sorbents and a reduction in their affinity (Langmuir parameter b) compared with control biomass. A difference between predicted and experimental data obtained for biomass grown on bentonite medium was also observed. The connection between the sorption capacity of biomass grown in clay‐containing medium, mycelial morphology and the structure of fungal pellets is discussed and a mechanism for the changed sorption capacity of the combined biomineral sorbents is proposed which involves blocking or modification of binding sites on biotic and abiotic components of the ‘biomineral’ association. © 2002 Society of Chemical Industry     

Anhydrous esterification of myristic acid with propylene: Ion exchange resin and acid-treated clay as catalysts

Anhydrous esterification of myristic acid with propylene was carried out in the temperature range of 110–145°C and pressure from 190–195 psig in the presence of Amberlyst-15 (cation exchange resin) and Filtrol-24 (acid-treated clay) as catalysts. The product ester, isopropyl myristate finds use in cosmetic and topical medicinal preparations where good absorption through the skin is desired. Filtrol-24 is the catalyst of choice, and the recommended operating temperature is 130°C with a pressure of 190 psig.