Quality enhancement of the abundant under‐valued crustacean,lobster krill (Munida spp.), during its chilled storage

Lobster krill (Munida genus) represents an under‐valued crustacean frequently caught on European fishing banks. In this work, its sensory, microbiological and biochemical qualities were evaluated during chilled storage. Additionally, the effects of a prestorage antimelanosic treatment consisting of soaking in sodium metabisulphite (SMB) solutions at two different concentrations (0.25% and 0.75%) were also studied. SMB prestorage treatment provided lobster specimens that still exhibited acceptable sensory quality after 10 days of storage, while control specimens were unacceptable at that time. SMB treatment also resulted in a significant (P < 0.05) inhibition of microbial growth, mainly of Enterobacteriaceae, psychrotrophes and proteolytic bacteria. Low lipid oxidation levels were observed for all batches; however, a significantly higher (P < 0.05) retention of polyunsaturated fatty acids was found in SMB‐treated lobster, especially in the 0.75% SMB batch. The results presented here open the way to the potential commercialisation of currently under‐utilised lobster krill as a chilled product.     

Study of the effect of BDMA catalyst in the epoxy novolac curing process by isothermal DSC

Epoxy novolac/anhydride cure kinetics has been studied by differential scanning calorimetry under isothermal conditions. The system used in this study was an epoxy novolac resin (DEN431), with nadic methyl anhydride as hardener and benzyldimethylamine as accelerator. Kinetic parameters including the reaction order, activation energy and kinetic rate constants, were investigated. The cure reaction was described with the catalyst concentration, and a normalized kinetic model developed for it. It is shown that the cure reaction is dependent on the cure temperature and catalyst concentration, and that it proceeds through an autocatalytic kinetic mechanism. The curing kinetic constants and the cure activation energies were obtained using the Arrhenius kinetic model. A suggested kinetic model with a diffusion term was successfully used to describe and predict the cure kinetics of epoxy novolac resin compositions as a function of the catalyst content and temperature. Copyright © 2003 Society of Chemical Industry     

在二(2-乙基己基)磷酸钠的微乳液中金属萃合物对水增溶的影响

测算了由二（2－乙基己基）磷酸钠，金属盐（CoSO4,NiSO4,ZnSO4,MgCl2或Cr(NO3)3)水溶液，正辛醇和正辛烷组成的微乳液中正辛醇从连续油相到界面的ΔGo→i^o和水的极限增容量φ'H2O。用金属萃取络合物反胶束的形成及其亲油性解释了金属离子对φ'H2O和ΔGo→i^o的影响。     

十二酰胺丙基二甲基羟乙基氯化铵与十二烷基硫酸钠水溶液的表面吸附和胶束形成

利用十二酰胺丙基二甲胺和氯乙醇反应 ,合成了十二酰胺丙基二甲基羟乙基氯化铵 (DDHA)阳离子表面活性剂 ,将其与十二烷基硫酸钠 (SDS)以不同摩尔比进行混合 ,测定了混合系统的表面张力 ,计算了单一系统和混合系统的饱和吸附量、分子最小截面积 ,表面层和胶束中 DDHA的摩尔分率及分子间相互作用参数 ,目视观察了混合系统的浑浊情况。结果表明 :在降低γcmc和 cmc方面 ,DDHA SDS混合系统有协同效应 ,表面层和胶束的组成与二组分配比有关 ,但是非对称的 ,等物质的量混合物中 ,DDHA在胶束和表面层中具有较大的摩尔分数。DDHA与 SDS在实验测定的各混合系统中都不出现混浊     

过氧化甲乙酮合成研究

论述了过氧化甲乙酮的合成方法，用阳离子交换树脂催化剂代替传统的无机酸催化剂。考察了离子交换树脂用量、反应温度对反应产率、活性氧含量的影响及溶剂对产品稳定性的影响。     

镁钴铝类水滑石催化合成安息香甲醚

采用共沉淀法制备了镁钴铝类水滑石化合物(MgCoAl-HTLcs),并用 X 射线衍射、扫描电子显微镜、NH_3程序升温脱附等方法对 MgCoAl-HTLcs 进行了表征,并以 MgCoAl-HTLcs 为催化剂催化苯甲醛与甲醇反应合成安息香甲醚,研究了n(Mg):n(Co):n(Al)、催化剂用量、原料配比、反应温度、反应时间对合成反应的影响。表征结果显示,MgCoAl-HTLcs 的晶相完整,表面主要为弱酸、弱碱性。催化合成安息香甲醚的适宜条件为:MgCoAl-HTLcs 催化剂用量0.10 g(约为原料总质量的0.23%),n(Mg):n(Co):n(Al)=0.4:1.6:1.0,V(苯甲醛):V(甲醇)=3:50,反应温度50℃,反应时间150 min。在此条件下,苯甲醛的平衡转化率达77.49%,安息香甲醚选择性接近100%。为洁净合成安息香甲醚开辟了一条新的途径。     

KCl与NaCl在低盐固态法酱油发酵中的应用比较

对KCl与NaCl在低盐固态酱油发酵中的应用进行了比较研究。结果表明：用KCl代替NaCl，KCl的浓度要高于NaCl才能抑制发酵期间杂茵的污染，且使用KCl的发酵效果比NaCl要好。     

由碳五馏分合成甲基叔戊基醚工艺的研究

以催化裂化C_5馏分与工业甲醇为原料,D005型大孔强酸型阳离子交换树脂为催化剂,采用筒式膨胀床双反应器,考察了甲基叔戊基醚的合成工艺条件。一阶反应器的操作条件为：循环比为2：1,醇烯比为1.2：1,入口温度为70℃,空速为6 h~(-1),平均转化率为53.63%；二阶反应器的操作条件为：入口温度为50℃,空速为1.2h~(-1),平均转化率为71.32%,全调合方案可以使催化裂化汽油的辛烷值平均提高0.55个单位。     

反应精馏法制备高纯度醋酸甲酯

在中试反应精馏塔中以浓硫酸为催化剂进行了醋酸与甲醇反应制备醋酸甲酯的试验。反应精馏塔的精馏段为填料,反应段为立体催化精馏塔板,采用连续操作,考察了回流比、甲醇进料位置、停留时间、催化剂用量对反应精馏的影响。试验结果表明,当回流比为1.2、甲醇进料位置为第11～15块塔板、停留时间为2.2～2.5h、催化剂与醋酸的质量比为1.07∶100时,塔顶醋酸甲酯的质量分数达到99.50%以上,醋酸的转化率达到99.85%以上。     

溶液中微量甲基异丁基酮的分析方法

研究了微量甲异丁基酮在氟氧铌酸（H2NbOF5)及氟钽酸（H2TaF7)溶液中存在的形式，找到利用碘仿-硫代硫酸钠联合滴定的方法，来标定微量甲基异丁基酮在H2NbOF5及H2TaF7溶液中的含量，本方法在钽铌冶炼过程中操作简便易行且结果重现性好。