High-temperature stabilization of polypropylene using hindered phenol–thioester stabilizer combinations,Part 1: Optimization and efficacy via nondust blends

The thermal degradation of unstabilized polypropylene has been investigated under long-term processing (twin extruder) and thermal aging at 150°C, with additive concentration studies on combinations of an established hindered phenolic antioxidant (pentaerythritol tetrakis (3-(3,5-di-tert-butyl-4-hydroxyphenyl) propionate) [S1010] and two popular thioesters (distearyl-3,3′-thiodipropionate [DSTDP] and didodecyl-3,3′-thiodipropionate [DLTDP]) using melt flow rate, carbonyl index and powder diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) (FTIR), and differential scanning calorimetry (DSC) (oxidation induction time [OIT]) and ultimate embrittlement time (Fracture) on injection-molded test pieces. It was found that 20:80 phenol:thioester ratios provided the best long-term thermal stability (LTTS); however, this was the reverse for processing stabilization (80:20), underlining the antioxidant nature of the two stabilizers (long term vs. melt). Melt preblending of the stabilizers (to form a no-dust blend) gave rise to improved LTTS. DRIFTS FTIR indicated that there was an improvement in preblending the additives, which removed any volatile impurities. Increased additive dispersion and localized potential efficacy in the stabilization cycle is important, as well as possible improved addition of the additives to the extruder rather than fine powder. The data are discussed in relation to the long-term stabilization of polypropylene in high-temperature applications such as under the bonnet of automobiles where minimizing stabilizer losses and maximizing synergy are important.     

采用温控和碘吸收池技术的发射激光稳频技术

多普勒测风激光雷达通过分析系统回波信号的多普勒频移反演出风速，为提高风场探测精度，从稳频技术方面展开研究。在稳频过程中，分别采取措施消除激光频率的长期漂移和短期抖动。针对激光频率的长期漂移，设计并研制了种子激光器温控箱，通过水浴的控温方式大大减小了激光频率的长期漂移，将激光频率稳定在±50 MHz以内；针对激光频率的短期抖动，采用以碘分子吸收池为核心器件的稳频系统，通过半导体控温方式对碘分子吸收池精确控温，控温精度达0.03 ℃，提高了稳频精度，将激光频率进一步稳定在±8 MHz以内，满足±10 MHz以内的设计精度要求。通过搭建多普勒测风激光雷达系统，对发射激光稳频装置进行系统验证，连续4组风场观测结果表明:系统探测高度为17 km，绝大部分方差在4 m/s以下，满足测风激光雷达测量指标的要求。     

水浴振荡碱消解-火焰原子吸收法测定土壤中六价铬

建立了水浴振荡碱消解-火焰原子吸收法测定土壤中的六价铬的方法。称取经风干、研磨并过0.15 mm孔径筛的土壤样品2.0 g(精确至0.01 g)置于150 mL锥形瓶中,加入25.0 mL碱性提取溶液,再加入400 mg氯化镁和0.5 mL磷酸氢二钾-磷酸二氢钾缓冲溶液,用聚乙稀薄膜封口,置于水浴恒温振荡器中。常温振荡样品5 min后,开启加热装置,加热水浴振荡至90～95℃,保持90 min。取下,冷却至室温。过滤,用硝酸调节溶液pH至7.5±0.5,将此溶液定容至50 mL容量瓶中,摇匀,待测。该方法采用水浴振荡碱消解的前处理方式进行土壤中六价铬的全消解,代替了磁力搅拌加热方式的消解,优化了前处理条件,简化了试验步骤,节约了分析测试时间,提高了分析效率,此方法还有利于处理大批量土壤样品。探讨了样品前处理提取温度的优化选择、氯化镁加入量的研究优化、提取时间的优化选择、pH值的优化以及三价铬干扰试验的影响。确认了最优化的仪器条件,对六价铬做了线性范围测试,曲线相关系数均在0.999以上。依据HJ 168—2020方法做了检出限,六价铬的检出限为0.5 mg/kg,以4倍检出限做测定下限,则测定下限为2.0 mg/kg。(取样量为2.0 g,定容体积为50 mL)。选取GBW(E)07251—255系列标准物质进行测试试验,试验结果的精密度和准确度均可满足土壤环境监测技术规范的要求。     

大豆蛋白纳米纤维对铁纳米颗粒的稳态化作用

为明确大豆蛋白纳米纤维的结构形成和扩宽铁强化剂的食品工业应用，以大豆分离蛋白（soy protein isolate，SPI）为原料，通过5 h的酸热处理制备纳米纤维（soy protein isolate fibrils，Fib SPI），系统研究纤维形成前后蛋白结构的变化，并进一步制备铁纳米颗粒（iron nanoparticles，Fe NPs），探究Fib SPI对铁的稳态化作用。研究结果表明：在酸热处理过程中，SPI产生大量的β-折叠结构，其与硫磺素T结合，显示出增强的荧光强度；此外，7S组分先发生降解，利于纤维成核形成，随后11S逐渐被水解，促进纤维生长；同时水解产生大量的小肽组分，提高了产物的还原力。研究进一步利用Fib SPI递送铁纳米颗粒（Fe NPs），发现与原始SPI相比，铁纳米颗粒可在Fib SPI原位形成胶体稳定的铁-大豆蛋白纳米纤维复合物（Fe FibSPI），并以Fe（II）形式存在，其对乳液体系色泽及稳定性的影响较硫酸亚铁或氯化铁小。该研究可为构建新型植物基铁强化剂递送体系提供理论和方法指导。     

Effect of sintering temperature on lightweight aggregates manufacturing from copper contaminated soil

Manufacturing lightweight aggregate (LWA) at high temperature is an effective way to immobilize heavy metals in solid waste. This work investigated the performance and solidification mechanism of LWA prepared from copper contaminated soil. The volume expansion of LWA could reach a maximum of 28%, and its lowest density accounted of 1.5 g/cm³, which met the standard requirements. Optical microscope and micro-CT test illustrated that the addition of Cu leaded to obvious phase separation in LWA. The Cu leaching result of LWA first increased and then dropped with the temperature. The XRD test found that the main formation phase of Cu in LWA were t-CuFe₂O₄ and amorphous phase that they had different acid resistance ability. XPS revealed that the main cause of the agglomeration of liquid phase in LWA was the chain broken reaction between Cu and Si–O tetrahedron. SEM-EDS results showed that the distribution of Cu and Si had a strong correlation, which meant that Cu mostly formed amorphous phase. This work showed the uniqueness of Cu in the high temperature immobilization and pointed out the best immobilization target phase.     

木质纤维与水泥共同改良软土的力学性能与微观机制分析

通过压实试验、无侧限抗压强度试验和劈裂试验,分析不同木质纤维含量、水泥含量和固化时间对软土力学性能的影响规律,探讨木质纤维、水泥改良软土的微观机制。结果表明,木质纤维的加入对水泥改良软土的击实特性有显著的影响;木质纤维与水泥可有效改善土体的抗压和劈裂抗拉强度,随着木质纤维含量的增加,改良土的抗压和劈裂抗拉强度呈现出明显的“驼峰”现象,并在木质纤维含量为0.25%时最大;木质纤维与水化产物、软土颗粒形成互锁效应,增大了改良土的摩擦力,同时木质纤维还承担一定的拉伸强度,使改良土的劈裂强度增加。     

不同消解方法对土壤中铜锌测定的影响

采用微波消解法和石墨消解法对土壤样品进行预处理,用火焰原子吸收分光光度法测定土壤中铜和锌的含量。对3个土壤标准物质(GSS-17、GSS-30、GSS-34)的精密度和准确度进行了分析,结果表明:微波消解法和石墨消解法的检出限、精密度和准确度均能满足土壤检测的要求,石墨消解法相对于微波消解法更加便捷,具有很好的精密度和准确度。     

Melt processing and characterization of tricalcium phosphate filled polybutylene adipate-co-terephthalate/polymethyl methacrylate composites for biomedical applications

Abstract

PBAT/PMMA/MA/TCP composites were prepared by melt blending and characterized by FTIR, XRD, SEM and in vitro bioactivity studies using SBF and cell viability tests. SBF studies revealed good bioactivity nature which was observed in SEM and confirmed by EDAX. Cell viability test revealed an excellent viability of squamous cells within 2?h than the control. Soil burial tests of the composites show fast degradation within 50 days under natural conditions. The tensile and hardness properties is marginally increased than that of PBAT/PMMA blend. These biocomposites can be used for the fabrication of medical devices by melt blending and injection molding process.     

Ultimate bearing capacity of strip footing resting on clay soil mixed with tire-derived aggregates

This study investigated the use of recycled tire-derived aggregate (TDA) mixed with kaolin as a method of increasing the ultimate bearing capacity ( UBC) of a strip footing. Thirteen 1g physical modeling tests were prepared in a rigid box of 0.6 m × 0.9 m in plan and 0.6 m in height. During sample preparation, 0%, 20%, 40%, or 60% (by weight) of powdery, shredded, small-sized granular (G 1–4 mm) or large-sized granular (G 5–8 mm) TDA was mixed with the kaolin. A strip footing was then placed on the stabilized kaolin and was caused to fail under stress-controlled conditions to determine the UBC. A rigorous 3D finite element analysis was developed in Optum G-3 to determine the UBC values based on the experimental test results. The experimental results showed that, except for the 20% powdery TDA, the TDA showed an increase in the UBC of the strip footing. When kaolin mixed with 20% G (5–8 mm), the UBC showed a threefold increase over that for the unreinforced case. The test with 20% G (1–4 mm) recorded the highest subgrade modulus. It was observed that the UBC calculated using finite element modeling overestimated the experimental UBC by an average of 9%.