Non-Halogenated-Solvent Processed and Additive-Free Tandem Organic Solar Cell with Efficiency Reaching 16.67%

Organic solar cells (OSCs) have recently reached a remarkably high efficiency and become a promising technology for commercial application. However, OSCs with top efficiency are mostly processed by halogenated solvents and with additives that are not environmentally friendly, which hinders large-scale manufacture. In this study, high-performance tandem OSCs, based on polymer donors and two small-molecule acceptors with different bandgaps, are fabricated by solution processing with non-halogenated solvents without additive. Importantly, the two active layers developed from non-halogenated solvents show better phase segregation and charge transport properties, leading to superior performance than halogenated ones. As a result, a tandem OSC with high efficiency of up to 16.67% is obtained, showing unique advantages in future massive production.     

Direct View on the Origin of High Li+ Transfer Impedance in All-Solid-State Battery

Large interfacial resistance plays a dominant role in the performance of all-solid-state lithium-ion batteries. However, the mechanism of interfacial resistance has been under debate. Here, the Li⁺ transport at the interfacial region is investigated to reveal the origin of the high Li⁺ transfer impedance in a LiCoO₂(LCO)/LiPON/Pt all-solid-state battery. Both an unexpected nanocrystalline layer and a structurally disordered transition layer are discovered to be inherent to the LCO/LiPON interface. Under electrochemical conditions, the nanocrystalline layer with insufficient electrochemical stability leads to the introduction of voids during electrochemical cycles, which is the origin of the high Li⁺ transfer impedance at solid electrolyte-electrode interfaces. In addition, at relatively low temperatures, the oxygen vacancies migration in the transition layer results in the formation of Co₃O₄ nanocrystalline layer with nanovoids, which contributes to the high Li⁺ transfer impedance. This work sheds light on the mechanism for the high interfacial resistance and promotes overcoming the interfacial issues in all-solid-state batteries.     

南方地区造纸车间钢屋面保温厚度的计算与分析

本文从内表面防结露、夏季隔热2个角度出发，对夏热冬冷及夏热冬暖地区代表城市采用的钢结构屋面的保温（隔热）层厚度进行计算分析。研究表明，在夏季室内温、湿度达到某一状态时，隔热厚度要大于冬季防结露的保温厚度。因此，夏热冬冷地区的造纸车间钢屋面保温层厚度应按夏季隔热计算确定，并进行冬季防结露验算；夏热冬暖地区按照冬季防结露计算即可。     

一种新的应用于5G中的自适应波束赋形优化算法

5G standard uses millimeter wave band to realize communication. In order to cover more reasonable in 5G communication system, beamforming technology must be adopted. To speed up the convergence, a novel algorithm based on the SWO criterion is proposed which can be applied in millimeter wave communication. The simulation results show that compared with other beamform- ing algorithms, the proposed algorithm can achieve higher convergence speed and is more realizable.     

核电厂立式泵电机多故障耦合振动问题的处理

某核电厂立式水泵配套电机存在两径向方向振动差异大、启机后振动缓慢上升的振动现象，为解决该问题，本文利用频谱分析、固有频率分析、相位分析等方法进行故障诊断，判断出该配套电机存在结构共振、转子热弯曲、动不平衡的耦合问题，并最终通过调整螺栓及现场动平衡方法成功解决了振动问题。      

生产工艺多方案并行与快速转换方法研究

生产系统复杂多变,在生产管理过程中存在多变性和不均衡性。对此,实际生产中需要实现生产工艺多方案并行与快速转换。分析了生产过程变化因素,介绍了主工艺+子工艺这一生产工艺多方案并行与快速转换方法,并通过实例验证了这一方法的有效性。     

吸潮对食用香精香料微胶囊质构和声学特性的影响

为评估吸潮对食用香精香料微胶囊的品质影响,分别测定吸潮前后6种自制食用香精香料微胶囊(设定直径为2.5 mm和3.5 mm)的质构和声响特性。结果表明:微胶囊的生产设定直径越小,则其实际直径偏离越大,可能与制备方法及壁材芯材相容性有关。微胶囊吸潮前,其破碎力均值分布在10.04 N～17.78 N范围内,最大形变量均值分布在33.5%～46.5%范围内,均存在较大差异且标准差较大;破碎声音强度均值分布在76.9 dB～83.8 dB范围内,具备一定差异同时标准差较小。吸潮后,微胶囊的破碎力均值同时具备下降、不变和升高的情况;最大形变量均值出现了显著升高,但依旧具备较大标准差;破碎声强出现了显著降低且标准差依旧较小。以上结果表明,相比于微胶囊的质构特性,破碎声强可更好的反应微胶囊储存期间的品质波动,可作为食用香精香料微胶囊品质判断指标之一。     

Ni-P/HZSM-5催化木质素降解制备酚类化学品

采用Ni-P复合改性HZSM-5催化剂催化木质素降解制备高附加值的单酚类化学品，探讨了催化剂种类、金属负载量、反应温度、反应时间以及溶剂种类对木质素催化降解制备酚类化合物的影响。同时采用X射线衍射仪（XRD）、比表面积和孔径分析仪（BET）、化学吸附仪（NH₃-TPD）、热重分析仪（TG）以及气相色谱质谱联用仪（GC/MS）对催化剂以及液相产物进行分析表征，同时探讨其催化失活以及再生机制。结果表明：Ni、P高度分散在HZSM-5催化剂的表面，Ni的添加有效地弱化了C－C键，致使β-O-4和α-O-4发生断裂，有效地提高了木质素加氢解聚的活性，减少了焦炭的生成，但催化剂的再生水热稳定性较差，重复使用性较低。当采用甲醇为供氢试剂，在反应温度为220℃，氢气压力为2MPa，反应时间为8h，催化剂负载量为10%，NaOH为共催化剂时，其木质素的转化率为98.6%，酚类化合物的含量达到74.97%。产物以苯酚、愈创木酚和紫丁香酚为主，低温促进了紫丁香酚的产生。     

原子层沉积技术对纤维素膜功能化的影响

为扩大纤维素膜的使用范围,使其可应用于医用、建筑等领域,利用纳米氧化锌具有紫外线屏蔽、抗菌等特性,采用原子层沉积(ALD)技术在纤维素膜表面沉积纳米氧化锌,制备具有紫外线阻隔以及抗菌功能的纤维素膜,并探讨不同ALD温度和循环次数对纤维素膜性能的影响。借助紫外分光光度计、扫描电子显微镜、X射线衍射仪、热重分析仪等对纤维素膜的结构和性能进行分析。结果表明:随着ALD温度和循环次数的增加,纤维素膜的紫外线透过率由74.50%下降至1.46%; ALD功能化纤维素膜对金黄色葡萄球菌的抑菌率高达99.9%;经改性的纤维素膜表面附着了六方晶系纤锌矿结构的纳米氧化锌层,残碳率由16.61%增加至31.20%。