NH_3-OH体系中共沉淀法同时回收钕铁硼废料中Nd-Pr-Co-Fe

为了避免回收单一钕铁硼废料中有价元素带来的操作复杂和资源浪费等问题,本研究采用共沉淀法共沉淀出钕铁硼废料中的有价元素Me(Nd,Pr,Co,Fe),制备可用于生产再生钕铁硼的原料;根据质量守恒和同时平衡原理,采用MATLAB软件建立Me(Nd,Pr,Co,Fe)-OH--NH3热力学模型,绘制lg[Me]-p H曲线模拟共沉淀工艺,并根据模拟结果确立了共沉淀工艺;模拟和实验的结果表明:根据lg[Me]-p H模拟结果可以确立一步共沉淀法的p H:6~10,Fe3+比Fe2+更易于沉淀完全;在上述条件下获得的共沉淀粉末主相均为Nd,Pr,Co,Fe的化合物,且有价元素的百分比含量均大于99.4%;其中,当p H值在8左右时回收率最高,在该条件下金属元素Me(Nd,Pr,Co,Fe)的沉淀效率分别为:98.7%,99.9%,93.6%,99.9%。该结果也表明共沉淀法工艺不仅高效,而且所制备的共沉淀粉末可以满足制备二次钕铁硼的需要。     

中职学籍档案管理的问题分析及对策

通过对档案管理中存在的问题进行分析，提出了提高学籍档案管理效率的对策，以期能为中职学籍档案的管理工作提供有益的参考和借鉴。     

餐饮废油生物柴油低温流动性的改进研究

使用气-质联用仪测定餐饮废油生物柴油(WCME)和-10号柴油(-10PD)的组成,使用冷滤点试验器和运动黏度试验器测定WCME的低温流动性,同时使用调合、添加低温流动性改进剂的方法改进WCME的低温流动性。实验结果表明,WCME主要由饱和脂肪酸甲酯和不饱和脂肪酸甲酯组成,质量分数分别为27.63%和71.81%;WCME冷滤点为0℃,运动黏度(40℃)为4.41mm2/s;WCME与-10PD调合后,冷滤点降低,其中B20的冷滤点最低,为-13℃,运动黏度随着WCME的体积分数的减少,逐渐接近-10PD的运动黏度。通过添加低温流动性改进剂,WCME,B10,B20的冷滤点分别从0,-8,-13℃降至-4,-26,-25℃。     

Analysis of phosphorus removal and anaerobic selector performance in a full-scale activated sludge process in Singapore.

This paper analyses the performance of the anaerobic selector (A/O process) in a full-scale activated sludge process receiving mostly industrial sewage discharge (> 60%) in Singapore. In addition to the sludge settleability, enhanced biological phosphorus removal (EBPR) was studied. The sludge volume index (SVI) reduced from 200 to 80 ml g(-1) and foaming was suppressed significantly, indicating the effectiveness of the anaerobic selector in improving sludge settleability. The phosphorus removal efficiency was 66%, and 7.5 mg HAc-COD was consumed per mg PO4(3-) -P removed. In the anaerobic compartment, 31% of the SCOD and 73% of the acetic acid in the settled sewage were removed with PO4(3-) -P release of 14.1 mg PO4(3-)-P l(-1). The linear correlation between PO4(3-) -P release in the anaerobic compartment and PO4(3-) -P uptake in the aerobic compartment indicates that there is about 0.8 mg PO4(3-) -P release in the anaerobic compartment per mg PO34(3-) -P uptake in the aerobic compartment. The fates of volatile fatty acids (VFAs) and its short chain acids (SCAs) in the process were studied and discussed.     

New hybrid fuzzy controller for direct torque control induction motor drives

A new hybrid fuzzy controller for direct torque control (DTC) induction motor drives is presented in this paper. The newly developed hybrid fuzzy control law consists of proportional-integral (PI) control at steady state, PI-type fuzzy logic control at transient state, and a simple switching mechanism between steady and transient states, to achieve satisfied performance under steady and transient conditions. The features of the presented new hybrid fuzzy controller are highlighted by comparing the performance of various control approaches, including PI control, PI-type fuzzy logic control (FLC), proportional-derivative (PD) type FLC, and combination of PD-type FLC and I control, for DTC-based induction motor drives. The pros and cons of these controllers are demonstrated by intensive experimental results. It is shown that the presented induction motor drive is with fast tracking capability, less steady state error, and robust to load disturbance while not resorting to complicated control method or adaptive tuning mechanism. Experimental results derived from a test system are presented confirming the above-mentioned claims.     

Modeling node mobility for reliable packet delivery in mobile ip networks

In this paper, we analyze node mobility for reliable packet delivery in mobile IP networks. In mobile IP, packets destined to roaming nodes are intercepted by their home agents and delivered via tunneling to their care of addresses (CoA). A mobile node may roam across multiple subnets. At each boundary crossing, a handoff is initiated such that the CoA is updated and a new tunnel is established. We consider both basic mobile IP handoff and smooth handoff. We find that reliable packet delivery in mobile IP networks can be modeled as a renewal process, because the retransmission over a new tunnel after each boundary crossing is independent of the previous history. We then derive the probability distribution of boundary crossings for each successful packet, based on which the packet reliable delivery time can be obtained. Our analytical model is derived based on a general distribution of residence time in a subnet and a general distribution of successful retransmission attempts in each subnet. The results can be readily applied to any distributions for both items. We also provide numerical examples to calculate the probability distribution of boundary crossings, and conduct simulations to validate our analytical results     

Reliability investigation of 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel

The authors have investigated the reliability performance of G-band (183 GHz) monolithic microwave integrated circuit (MMIC) amplifiers fabricated using 0.07-/spl mu/m T-gate InGaAs-InAlAs-InP HEMTs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel on 3-in wafers. Life test was performed at two temperatures (T/sub 1/ = 200 /spl deg/C and T/sub 2/ = 215 /spl deg/C), and the amplifiers were stressed at V/sub ds/ of 1 V and I/sub ds/ of 250 mA/mm in a N/sub 2/ ambient. The activation energy is as high as 1.7 eV, achieving a projected median-time-to-failure (MTTF) /spl ap/ 2 /spl times/ 10/sup 6/ h at a junction temperature of 125 /spl deg/C. MTTF was determined by 2-temperature constant current stress using /spl Delta/G/sub mp/ = -20% as the failure criteria. The difference of reliability performance between 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel and 0.1-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with In/sub 0.6/Ga/sub 0.4/As channel is also discussed. The achieved high-reliability result demonstrates a robust 0.07-/spl mu/m pseudomorphic InGaAs-InAlAs-InP HEMT MMICs production technology for G-band applications.