氮含量及固溶温度对21-6-9奥氏体不锈钢组织和硬度的影响

为了探讨氮含量及固溶温度对21-6-9不锈钢组织和硬度的影响,分别在950、1000、1050和1100 ℃对3种不同氮含量的热轧态21-6-9不锈钢进行1 h固溶处理,通过光学显微镜观察其组织结构,结合Thermo-Calc热力学计算对试验钢的微观组织进行分析,并对其进行硬度测试。结果表明,0.20%~0.28%N的21-6-9不锈钢热轧后沿轧制方向析出铁素体,且钢中铁素体经950~1100 ℃固溶处理可消除,当N含量达到0.34%时,试验钢中不再出现铁素体。随着固溶处理温度的升高,21-6-9不锈钢的晶粒组织长大,硬度降低。N含量的增加可显著提高固溶态21-6-9不锈钢的硬度,其增加程度随固溶处理温度的升高而减弱。     

Er3+-Yb3+ ions doped fluoro-aluminosilicate glass-ceramics as a temperature-sensing material

The transparent Er³⁺-Yb³⁺-doped fluoro-aluminosilicate glass-ceramic (GC) was prepared by melt-quenching. The crystal phase, morphology, and up-conversion (UC) luminescence of as-produced GC were characterized by X-ray diffraction, scanning electron microscopy, and fluorescence spectrophotometry, respectively. The results show that BaYF₅ nanocrystals were uniformly distributed in the glass matrix of the as-produced GC. When the as-produced GC was subjected to heat treatment, the crystallinity was increased, but the crystal identity remains unchanged. Such heat-treatment doubled the intensity of the UC luminescence, and this enhancement was ascribed to the increased incorporation of both Er³⁺ and Yb³⁺ ions into the lower phonon energy environment of BaYF₅ nanocrystals. Furthermore, the heat-treated GC was stable against further crystallization, and consequently its UC luminescence was stable at the application temperature. The heat-treated GC was found to possess an outstanding temperature-sensing capability.     

Micro-expression recognition from local facial regions

MiE is a facial involuntary reaction that reflects the real emotion and thoughts of a human being. It is very difficult for a normal human to detect a Micro-Expression (MiE), since it is a very fast and local face reaction with low intensity. As a consequence, it is a challenging task for researchers to build an automatic system for MiE recognition. Previous works for MiE recognition have attempted to use the whole face, yet a facial MiE appears in a small region of the face, which makes the extraction of relevant features a hard task. In this paper, we propose a novel deep learning approach that leverages the locality aspect of MiEs by learning spatio-temporal features from local facial regions using a composite architecture of Convolutional Neural Network (CNN) and Long Short Term Memory (LSTM). The proposed solution succeeds to extract relevant local features for MiEs recognition. Experimental results on benchmark datasets demonstrate the highest recognition accuracy of our solution with respect to state-of-the-art methods.     

Cu掺杂对有序Sr3YCo4-xCuxO10.5+δ多晶的结构与物理性能的影响

采用固相反应法制备了四方Sr3YCo4-xCuxO10.5+δ(x=0~1.0)多晶。用热重-差示扫描量热分析,X射线衍射研究了多晶的有序化相变及结构。在固溶范围内(x=0~0.4),观察到有序峰(103)和(215),说明四方Sr3YCo4-xCuxO10.5+δ多晶为超结构,这是由于合成时在1000℃以上发生了吸氧(δ)有序化相变；当x=0.6~1.0时,978℃时在晶界处形成了单斜杂相,破坏了Sr3YCo4-xCuxO10.5+δ多晶的有序。当x=0~0.4时,多晶呈半导体输运行为。随着Cu掺杂量的增加,Co4+提供的空穴载流子浓度增大,电阻率明显下降；由于Cu的固溶,自旋熵增加,载流子浓度和自旋熵的共同作用使x=0~0.2多晶的热电势不变,x=0.4的热电势降低。并且Cu掺杂导致的晶格畸变使Co3+离子由高自旋态转变为高/低自旋混合态,磁化强度和铁磁转变温度(Tc)降低,磁结构由G-型反铁磁转变为铁磁。在进行二次烧结后,300K时电阻率明显降低,热电势为一次烧结的2倍,可能是二次烧结使多晶的有序化程度增大,提高了铁磁有序排列。     

Microstructure and some properties of powder-pack borided Ti–5Mo–5V–8Cr–3Al alloy with special attention to the microstructure at the interface TiB/substrate

The borided layer was prepared on the surface of the Ti–5Mo–5V–8Cr–3Al alloy by powder-pack boriding at 1000°C-10h. SEM, EPMA and TEM were used to investigate the effects of alloying elements (Al, V, Mo and Cr) on the growth of TiB whiskers in the borided Ti–5Mo–5V–8Cr–3Al alloy. Wear properties of borided Ti–5Mo–5V–8Cr–3Al alloy were investigated using dry reciprocating friction tests. SEM results show that the thickness of boride layer in Ti–5Mo–5V–8Cr–3Al alloy is thinner than that in the Cp-Ti. This is attributed to the enrichment of alloying elements especially V in TiB/substrate by TEM, which hinders the diffusion of B atoms, thus resulting in the short and thick TiB whiskers in Ti–5Mo–5V–8Cr–3Al alloy. Borided Ti–5Mo–5V–8Cr–3Al alloy has the better wear resistance than as-received alloy.     

NiFe layered double hydroxide as an efficient bifunctional catalyst for electrosynthesis of hydrogen peroxide and oxygen

Two electron oxygen reduction reaction to produce hydrogen peroxide (H₂O₂) is a promising alternative technique to the multistep and high energy consumption anthraquinone process. Herein, Ni–Fe layered double hydroxide (NiFe-LDH) has been firstly demonstrated as an efficient bifunctional catalyst to prepare H₂O₂ by electrochemical oxygen reduction (2e^? ORR) and oxygen evolution reaction (OER). Significantly, the NiFe-LDH catalyst possesses a high faraday efficiency of 88.75% for H₂O₂ preparation in alkaline media. Moreover, the NiFe-LDH catalyst exhibits excellent OER electrocatalytic property with small overpotential of 210 mV at 10 mA cm^?2 and high stability in 1 M KOH solution. On this basis, a new reactor has been designed to electrolyze oxygen and generate hydrogen peroxide. Under the ultra-low cell voltage of 1 V, the H₂O₂ yield reaches to 47.62 mmol g_cat^?1 h^?1. In order to evaluate the application potential of the bifunctional NiFe-LDH catalyst for H₂O₂ preparation, a 1.5 V dry battery has been used as the power supply, and the output of H₂O₂ reaches to 83.90 mmol g_cat^?1 h^?1. The excellent electrocatalytic properties of 2e^? ORR and OER make NiFe-LDH a promising bifunctional electrocatalyst for future commercialization. Moreover, the well-designed 2e^? ORR-OER reactor provides a new strategy for portable production of H₂O₂.     

Investigation into adsorption equilibrium and thermodynamics for water vapor on montmorillonite clay

The isothermal adsorption curves for water vapor on montmorillonite were measured by a gravimetric adsorption system. Dent's model was employed to estimate the adsorption behaviors of water vapor on primary adsorption sites and secondary adsorption sites. The thermodynamics analysis of water vapor adsorption was performed. At low vapor pressure region, primary adsorption predominates, and with increasing vapor pressure, secondary adsorption becomes notable. Primary adsorption sites have an evidently stronger adsorption affinity than secondary adsorption sites. With increasing vapor pressure, Gibbs free energy variation rapidly increases and then reduces slowly. Although increasing vapor pressure raises adsorption spontaneity on primary adsorption sites, the enhancement in vapor pressure decreases the spontaneity of water vapor adsorption on secondary adsorption sites. As adsorbed loading increases, isosteric heat of adsorption and entropy loss decrease first and then increase quickly. The gradually growing water clusters are responsible for the increase of entropy loss at late stage.     

机械活化对粉煤灰提铝影响研究

为提高粉煤灰中铝提取率, 采用机械活化对粉煤灰进行预处理, 探讨了机械活化对粉煤灰焙烧-酸浸效果的影响。结果表明: 机械活化能提高粉煤灰比表面积、增加反应活性点, 促进活化反应的进行; 通过机械活化, 在Na₂CO₃与Al₂O₃物质的量比1.6、850 ℃下焙烧50 min后酸浸, 铝浸出率达到91.58%。     

Designing independent water transport channels to improve water flooding in ultra-thin nanoporous film cathodes for PEMFCs

Utilization of 3D nanostructured Pt cathodes could obviously improve performances of proton exchange membrane fuel cells (PEMFCs) owing to the reduced tortuosity and the bi-continuous nanoporous structure. However, these cathodes usually suffer from the flooding problem ascribed to the ionomer-free and nanoscale pores which are more susceptible to water condensation. In this paper, ultra-thin nanoporous metal films (100 nm) were utilized to construct PEMFC cathodes and independent transport channels were designed separately for water and gas aiming at the flooding problem. Nanoporous gold (NPG) film was used as the model support for loading Pt nanoparticles owing to its controllable and stable structure. After optimizing the polytetrafluoroethylene (PTFE) content and carbon loading in the gas diffusion layer (GDL), plasma treatment under O₂ atmosphere was used to pattern the GDL with independent water transport channels. The obtained liquid permeation coefficients and oxygen gains demonstrated the obviously improved water and O₂ transport. By using a home-made optimized GDL and a nanoporous film cathode with pore size ～60 nm, the flooding problem could be facilely solved. With a Pt loading of ～16 μg cm^?2, this 3D nanostructured cathode exhibits a PEMFC performance of ～957 mW cm^?2 at 80 °C. The Pt power efficiency is about 4 times higher than that of the commercial Pt/C cathode (50 μg cm^?2, 756 mW cm^?2). Obviously, this study provides a simple but effective methodology to solve the water flooding problem in the ultra-thin nanoporous film cathodes which is applicable for other types of 3D nanostructured PEMFC cathodes.