Fabrication of paper based carbon/graphene/ZnO aerogel composite decorated by polyaniline nanostructure: Investigation of electrochemical properties

The cellulose derived carbon/graphene/ZnO aerogel composite was prepared as an electrode in order to investigate the electrochemical properties. Carbon aerogel was synthesized using paper as an available cellulose source, and the composite was obtained through a new and simple preparation method including the immersion of monolithic carbon aerogel in graphene oxide/Zn²⁺ suspension and subsequent chemical reduction and freeze drying. The morphology, functional groups and crystalline structure of the samples were studied with Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Diffraction Spectroscopy (XRD), respectively. Electrochemical performance of the prepared binder free electrodes was examined using Cyclic Voltammetry (CV), Galvanostatic Charge-Discharge (GCD) and Electrochemical Impedance Spectroscopy (EIS). The data revealed that flexible carbon/graphene/ZnO composite resulted in a low density (0.035 g cm⁻³) electrode with the capacitance of 900 mF cm⁻² at a high current density of 10 mA cm⁻², lower IR drop and high cyclic stability (capacitance retention of 96%) after 1000 cycles, at 10 mA cm⁻². These features were due to the presence of 3D porous conductive network, highly reduced graphene oxide, and the formation of ZnO nanoparticles on graphene sheets. Moreover, polyaniline (PANI) was introduced to carbon/graphene/ZnO composite electrode using electro-oxidation method at different reaction time and aniline concentration in order to achieve remarkably improved capacitance of 2500 mF cm⁻² (at 10 mA cm⁻²) and low charge transfer resistance. Also, after the supercapacitor device assembly, the capacitance was retained. Based on the results, the synthesized composite is a promising material for new generation of lightweight freestanding electrodes with the high electrochemical performance.     

Chemical bond characteristics and infrared reflectivity spectrum of a novel microwave dielectric ceramic CaIn2O4 with near-zero τf

Orthorhombic-structured CaIn₂O₄ ceramics with a space group Pca2₁ were synthesized via a solid-state reaction method. A high relative density (95.6 %) and excellent microwave dielectric properties (ε_r ～11.28, Qf = 74,200 GHz, τ_f ～ ?4.6 ppm/°C) were obtained when the ceramics were sintered at 1375 °C for 6 h. The dielectric properties were investigated on the basis of the Phillips–Van Vechten–Levine chemical bond theory. Results indicated that the dielectric properties were mainly determined by the InO bonds in the CaIn₂O₄ ceramics. These bonds contributed more (74.65 %) to the dielectric constant than the CaO bonds (25.35 %). Furthermore, the intrinsic dielectric properties of the CaIn₂O₄ ceramics were investigated via infrared reflectivity spectroscopy. The extrapolated microwave dielectric properties were ε_r ～10.12 and Qf = 112,200 GHz. Results indicated that ion polarization is the main contributor to the dielectric constant in microwave frequency ranges.     

3D CaP porous scaffolds with grooved surface topography obtained by the sol-gel method

The influence of surface topography on cellular behaviour and its importance for the development of three-dimensional scaffolds for bone tissue engineering are a topic of growing interest. To date, the introduction of topographical patterns into the surface of 3D porous ceramic scaffolds has proven difficult, due partly to the brittle nature of ceramic materials as well as the currently available fabrication technologies. In this study, a grooved pattern was introduced into the surface of 3D multilayer porous ceramic scaffolds by the chemical etching technique. The patterned scaffolds were characterised by X-Ray Diffraction (XRD), Scanning Electron Microscopy with Energy Dispersive X-Ray Spectroscopy (SEM-EDX) and Digital Holographic Microscopy (DHM). Their bioactivity was also evaluated in vitro by immersion in simulated body fluid (SBF) for 12 h, 1, 7, 14 and 21 days. Scaffolds were constituted mainly with a mixture of the calcium pyrophosphate (Ca₂O₇P₂) and β-tricalcium phosphate (Ca?(PO?)?) phases. The pyrophosphate on the external layer was dissolved as a result of the etching process, leaving grooves on the surface. Ridges and grooves were nano-/micrometric, with dimensions of around 900 nm–1.5 μm in width and 200 nm–300 nm in depth. Moreover, the mechanical properties and bioactive capacity of the patterned scaffolds were not affected by chemical etching, making them suitable to be used in bone tissue engineering.     

Photoluminescence and hydrogen evolution properties of ZnS:Eu quantum dots

In the era of Photonics, design and development of novel rare earth ion-doped quantum dots (QDs) for optoelectronic applications has gained significant interest owing to their outstanding characteristics. Simultaneously, the creation of a new class of photocatalytic materials on the nanoscale is also imperative for environmental purification. Thus, we report on wet chemical synthesis, the structural, morphological, and optical characteristics, fluorescence, and hydrogen evolution of ZnS:Eu (0, 2, 4, and 6 at%) QDs for optoelectronic and photocatalytic applications. Comprehensive structural studies depicted that Eu³⁺ ions were efficiently substituted into the host matrix and altered the original structure of the ZnS compound. The emission spectra of the ZnS:Eu QDs exhibited distinctive red fluorescence owing to the transition of dopant ions in ⁵D₀ - ⁷F₁, ⁵D₀ - ⁷F₂, ⁵D₀ - ⁷F₃, and ⁵D₀ - ⁷F₄ energy levels of the 4f orbital of the Eu³⁺ ions. Moreover, the photocatalytic properties of ZnS:Eu (6 at%) QDs possess better catalytic efficiency toward hydrogen evolution through a water splitting mechanism under simulated sunlight irradiation. The observed photocatalytic phenomenon in the synthesized samples agreed well with the luminescence properties exhibited by the QDs.     

A practical development of engineering simulation-assisted educational AR environments

Engineering simulations have opened several gates for today’s chemical engineers. They are powerful tools to provide technical content as physics-based numerical solvers. Augmented reality (AR) and virtual reality (VR), on the other hand, are already underway to digitize environments in many fields. The combination of AR/VR environments and simulations in engineering education has been attracting widespread interest. Literature has demonstrated a massive amount of digital educational environments in several contexts as being complementary to conventional educational methods. Nevertheless, hosting technical content produced by engineering simulations with educational AR/VR is still challenging and requires expertise from multiple disciplines throughout the technical development. Present work provides a facile and agile methodology for low-cost hardware but content-wise rich AR software development. Inspired by the Covid-19 pandemic, a case study is developed to teach chemical-engineering concepts using a liquid-soap synthesis process. Accordingly, we assess and conclude the digital development process to guide inexperienced developers for the digitalization of teaching content. The present contribution serves as an example of the power of integrating AR/VR with traditional engineering simulations for educational purposes. The digital tool developed in this work is shared in the online version.     

A numerical study on the combustion limits of mesoscale methane jet flames with hydrogen addition

A meso-scale jet flame model was established for the flame ports of domestic gas stoves. The influences of hydrogen addition ratio (β = 0%–25%) on the combustion limits were explored. The results show that with the increase of hydrogen addition ratio, the blow-off limit increases obviously, while the extinction limit decreases slightly, namely, the combustible range expands significantly. Quantitative analysis was carried out in terms of chemical effect and thermal effect. It was found that hydrogen addition will reduce O₂ fraction in the pre-mixture for a constant equivalence ratio. Under near-extinction limit condition, since the flame is located at the nozzle exit, the external O₂ cannot be entrained into or diffuse into the upstream of the flame, which leads to the decrease of reaction rate. However, for the near-blow-off cases, the external O₂ can be entrained and diffuse into the flame, which compensates the difference of O₂ content in the pre-mixture. Therefore, the combustion reaction is enhanced by hydrogen addition because more H radicals can be produced. In addition, as the flame is located closer to the tube with the increase of hydrogen addition ratio, heat transfer between flame and tube wall is augmented and the preheating of fresh mixture is strengthened by the inner tube wall. This heat recirculation effect becomes especially notable in low velocity cases. In conclusion, the extension of extinction limit by hydrogen addition is attributed to the thermal effect, while the increase of blow-off limit is mainly due to the intensification of chemical effect.     

Crystallization and relaxation dynamics of glass-forming liquids at the Kauzmann temperature

If the entropy extrapolation of supercooled liquids (SCL) suggested by Kauzmann was correct, then they would have the same entropy as their stable crystalline phase at a certain low temperature, below the laboratory glass transition (T_g), known as the Kauzmann temperature (T_K). Extrapolating even further, the liquid entropy would be null at a temperature above absolute zero, violating the Third Law of Thermodynamics and constituting a paradox. Several possibilities have been proposed over the past 70 years to solve this paradox with different degrees of success. Our objective here is to access liquid dynamics at deep supercoolings to test the so-called crystallization solution to the paradox. By comparing the relaxation and crystallization kinetics determined above T_g and extrapolated down to T_K, a possible solution would be that the crystallization time is shorter than the relaxation time, which would mean that a SCL cannot reach the T_K. In this case, the liquid stability limit or kinetic spinodal temperature (T_ks) should be higher than T_K. We tested two fragile glass-forming liquids (diopside and wollastonite) and two strong liquids (silica and germania). For the fragile substances, T_ks ? T_K, hence such a supercooled liquid cannot exist at T_K, and the entropy crisis is averted. On the other hand, the results for the strong liquids were inconclusive. We hope the findings of this work encourage researchers to further investigate the liquid dynamics of different strong glass-forming systems at deep supercoolings.     

Structural regulation and polishing performance of dendritic mesoporous silica (D-mSiO2) supported with samarium-doped cerium oxide composites

Ceria (CeO₂) particles are prevalent polishing abrasive materials. Trivalent lanthanide ions are the popular category of dopants for enriched surface defects and thus improved physicochemical properties, since they are highly compatible with CeO₂ lattices. Herein, a series of dendritic-like mesoporous silica (D-mSiO₂)-supported samarium (Sm)-doped CeO₂ nanocrystals were synthesized via a facile chemical precipitation method. The relation of the structural characteristics and chemical mechanical polishing (CMP) performances were investigated to explore the effect of Sm-doping amounts on the D-mSiO₂/Sm_xCe_1?xO_2?δ (x = 0–1) composite abrasives. The involved low-modulus D-mSiO₂ cores aimed to eliminate surface scratch and damage, resulting from the optimized contact behavior between abrasives and surfaces. The trivalent cerium (Ce³⁺) and oxygen vacancy (V_O) at CeO₂ surfaces were expected to be reactive sites for the material removal process over SiO₂ films. The optimal oxide-CMP performances in terms of removal efficiency and surface quality were achieved by the 40% Sm-doped composite abrasives. It might be attributed to the high Ce³⁺ and V_O concentrations and the enhancement of tribochemical reactivity between CeO₂SiO₂ interfaces. Furthermore, the relationship between the surface chemistry, polishing performance as well as the actual role in oxide-CMP of the D-mSiO₂/Sm_xCe_1?xO_2?δ abrasives were also discussed.     

Influence of tef flour and its association with other flours on the nutritional,technological, and sensory quality of bakery products

The objective of this study was to investigate chemical, technological, and sensory quality of tef in products made exclusively with tef flour and tef flour associated with other flours. The selection of the studies and the extraction of information were carried out through research in several databases. Tef flour was used in cakes, cookies, breads, cupcakes, muffins, and extruded snacks. Bread was the most evaluated product with tef flour associated with other flours or exclusively. Most of the outcomes were with tef (5–50%) associated with other flours. Increased levels of fibers, minerals, antioxidant capacity, and flavonoids were noted according to the percentage of tef. Technological characteristics demonstrated that these products showed intermediate final quality, due to the characteristics of volume, specific volume, firmness, and luminosity. Regarding sensory quality, studies that used (5–35%) tef flour associated with other flours were well-accepted.     

Diluted chemical bath deposition of CdZnS as prospective buffer layer in CIGS solar cell

In this study, dilute chemical bath deposition technique has been used to deposit CdZnS thin films on soda-lime glass substrates. The structural, morphological, optoelectronic properties of as-grown films have been investigated as a function of different Zn²⁺ precursor concentrations. The X-ray diffractogram of CdS thin-film reveals a peak corresponding to (002) plane with wurtzite structure, and the peak shift has been observed with the increase of the Zn²⁺ concentration upon formation of CdZnS thin film. From morphological studies, it has been revealed that the diluted chemical bath deposition technique provides homogeneous distribution of film on the substrate even at a lower concentration of Zn²⁺. Optical characterization has shown that the transparency of the film is influenced by Zn²⁺ concentration and when the Zn²⁺ concentration is varied from 0 M to 0.0256 M, bandgap values of resulting films range from 2.42 eV to 3.90 eV while. Furthermore, electrical properties have shown that with increasing zinc concentration the resistivity of the film increases. Finally, numerical simulation validates and suggests that CdZnS buffer layer with composition of 0.0032 M Zn²⁺ concentration would be a promising candidate in CIGS solar cell.