离子型稀土矿山淋洗及尾水富集试验研究

对浸矿后离子型稀土原地浸矿场采用清水进行淋洗，在184天的清水淋洗过程中，尾水氨氮值从最开始的507mg/L，降低至140mg/L，淋洗尾水pH4.52~3.10。淋洗尾水采用两级反渗透膜分离，既回收有价资源稀土，又能使出水氨氮达标。结果表明，产水氨氮浓度稳定低于15mg/L，对稀土的截留率高于98.25%，浓水中稀土离子平均浓度313.4mg/L，可进一步回收稀土资源。     

A numerical model to predict the powder–binder separation during micro-powder injection molding

The micro-powder injection molding (micro-PIM) process has the potential to bridge the gap between the design and manufacturing of micro-components that are often used in small and handy devices. Numerical modeling helps to analyze and overcome various difficulties of micro-PIM. In the present work, a numerical model is developed to predict the powder–binder separation (a common defect in PIM and especially severe in micro-PIM) during the injection of an alumina feedstock. A powder–binder separation criterion is proposed dealing with applied injection pressure and friction force between the powder and binder. An indirect comparison of feedstock travel time between two locations is used to validate the model. The predicted segregation from the simulated result is supported by a qualitative experimental measurement. The developed model can be used to optimize injection parameters to get a defect-free product.     

煤矿水仓清理新工艺

通过调研现场情况以及检测煤泥特性，探寻一种实用性强、方法简单的新工艺来替代劳累的人工和繁琐的机械清淤，解决现实问题。针对实际情况开发清仓新工艺，介绍了该工艺的技术路线选择、设计依据以及实际应用效果。该新工艺具有降低清仓时间、减轻工人劳动强度、设备操作简单、实用性强等特点。     

Fluid sloshing thermo-mechanical characteristic in a cryogenic fuel storage tank under different gravity acceleration levels

Fluid sloshing usually causes serious safety issues on the dynamic stability and propellant thermal management during the powered-flight phase of launch vehicle. With the wide using of cryogenic propellants, the coupled thermo-mechanical performance during fluid sloshing becomes more prominent. In the present study, one numerical model is established to simulate fluid sloshing by using the VOF method coupled with the mesh motion treatment. The phase change occurring within the tank is considered. Both the experimental validation and mesh sensitivity analysis are made. It shows that present numerical model is acceptable. Based on the developed numerical model, the effect of different super gravity accelerations on fluid sloshing hydrodynamic characteristic is numerically researched. The fluid pressure variation, the sloshing force and sloshing moment, the interface dynamic response and the interface shape variation are investigated, respectively. It shows that the gravity acceleration has caused obvious influences on fluid sloshing characteristic. When the gravity acceleration is higher than 4g₀, fluid sloshing becomes more obvious and must be paid enough attention. With some valuable conclusions obtained, the present work is of great significance for in-depth understanding of fluid sloshing mechanism.     

Synthesis of thermoresponsive copolymer/silica-coated magnetite nanoparticle composite and its application for heavy metal ion recovery

To enhance chemical stability and suppress of aggregation of magnetite nanoparticles (MNPs), which are used as a support for thermoresponsive copolymer immobilization, silica coating of the MNPs is applied via the electrooxidation method. Although the resulting silica coated-MNPs also formed aggregates, the size distribution of the aggregate shifted to smaller size range. Because of that, the surface area available for copolymer immobilization increased approximately 6.7 times at maximum as compared with that of the uncoated MNPs. It contributed to the increase of the amount of the immobilized copolymer on the silica-coated MNPs, which is approximately four times larger than that on the uncoated MNPs. Fe₃O₄ dissolution test confirmed enhancement of chemical stability of MNPs. The thermoresponsive copolymer immobilized on the silica-coated MNPs shows the ability to recycle Cu(II) ion from Cu(II) containing solution by changing temperature with significantly shorter time than those in other thermoresponsive adsorbents in gel form.     

Synthesis,characterization, and visible-light photocatalytic activity of transition metals doped ZTO nanoparticles

Transition metals doping has been proved to be a feasible way for tuning the physical properties on the surface and bulk of nanomaterials and also for the good performance in decontamination of emerging pollutants. In this context, doped samples of zinc tin oxide or zinc stannate nanoparticles (ZTO NPs) by several transition metals were synthesized in order to enhance the optical absorbance with the aims of reducing the band gap and therefore ameliorated their photocatalytic activity. They were characterized by the X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), diffuse reflectance spectroscopy, Raman spectroscopy and photoluminescence. The XRD patterns and the microscopic observations showed the formation of spherical nanoparticles with an average size of about 30 nm and highly pure ZTO phase with an inverse spinel structure. The Raman spectra were dominated by bands relatives to the F2g (2) and A1g symmetries modes of inverse spinel structure. The band gap Eg is estimated to be 3.75 eV for the undoped sample, and 3.67, 3.64, 3.78 and 3.21 eV, for 2% Fe, 2% Mg, 2% Gd, and 2% Mn doped ZTO samples, respectively.Furthermore, the undoped ZTO NPs have the intrinsic problem of recombination of photogenerated charge carriers. We have shown that the reduction of the band gap and oxygen vacancies resulting from the doping effect could be a useful tool for trapping and avoid the recombination of electrons coming from photosensitized rhodamine B (RhB) under visible light irradiation. Owing to the structural advantages and low band gap, 2% Mn doped ZTO NPs, with the kinetic rate constants k of 0.024 min⁻¹, show enhanced performance for the elimination of RhB in aqueous solution compared to undoped and other doped ZTO NPs.     

UV curing-assisted 3D plotting of ceramic feedstock containing thermo-regulated phase-separable,photocurable vehicle for dual-scale porosity structure

We propose a novel approach for manufacturing dual-scale porosity alumina structures by UV curing-assisted 3D plotting of a specially formulated alumina feedstock using a thermo-regulated phase separable, photocurable camphene/triethylene glycol dimethacrylate (TEGDMA) vehicle. In particular, 3D plotting process was conducted at - 5 °C, and thus an alumina suspension prepared using liquid camphene/TEGDMA at room temperature could undergo phase separation, resulting in camphene crystals surrounded by walls comprised of liquid photopolymer enclosing alumina particles. To enhance the shape retention ability of extruded filaments, polystyrene (PS) polymer was used as the tackifier. The phase-separated feedrod could be extruded favorably through a nozzle and rapidly photopolymerized by UV light during the 3D plotting process. Three-dimensionally interconnected macropores were tightly constructed, which were separated by microporous alumina filaments, where micropores were created by the removal of camphene crystals via freeze-dying. The macroporosity of porous alumina ceramics was controlled by adjusting the distance between deposited filaments, while their microporosity was kept constant, leading to tightly tailored overall porosity and mechanical properties.     

Synthesis of Ionic Ultramicroporous Polymers for Selective Separation of Acetylene from Ethylene

The design of highly stable and efficient porous materials is essential for developing breakthrough hydrocarbon separation methods based on physisorption to replace currently used energy-intensive distillation/absorption technologies. Efforts to develop advanced porous materials such as zeolites, coordination frameworks, and organic polymers have met with limited success. Here, a new class of ionic ultramicroporous polymers (IUPs) with high-density inorganic anions and narrowly distributed ultramicroporosity is reported, which are synthesized by a facile free-radical polymerization using branched and amphiphilic ionic compounds as reactive monomers. A covalent and ionic dual-crosslinking strategy is proposed to manipulate the pore structure of amorphous polymers at the ultramicroporous scale. The IUPs exhibit exceptional selectivity (286.1–474.4) for separating acetylene from ethylene along with high thermal and water stability, collaboratively demonstrated by gas adsorption isotherms and experimental breakthrough curves. Modeling studies unveil the specific binding sites for acetylene capture as well as the interconnected ultramicroporosity for size sieving. The porosity-engineering protocol used in this work can also be extended to the design of other ultramicroporous materials for the challenging separation of other key gas constituents.     

气动弹片对垂直轴风力机性能影响研究

片对垂直轴风力机气动性能的影响并分析了其流动机理。结果表明：气动弹片在高尖速比下可显著抑制流动分离并改善其动态失速特性，功率系数得到极大提升；切向力和转矩系数在气动弹片作用相位角范围内，均有一定提高，而在其它相位角内，风力机性能不受影响。     

铅锌多金属矿分段浓缩选别技术的研究与应用

通过多碎细磨、原矿分级溢流优先浓缩脱水,进行了高浓度选铅银、选锌,锌尾矿再浓缩脱水选硫、选锰,同时匹配合理的选矿药剂,原矿浓缩水回用于磨矿分级和选铅,锌尾浓缩水回用于选锌,尾矿浓缩水回用于选硫、选锰,剩余各种废水经适度处理回用于选铅和磨矿分级等,使一段磨矿细度-74μm从70%提高到80%,铅、锌、硫入选初始浓度分别提高到50%、40%、50%,选矿废水全部分质回用。铅锌硫银回收率分别提高了1.5、2.83、13.57、1.01个百分点,硫精矿主品位从38.9%提高到46.5%,设备减少40%、能耗降低25%,节约了选矿药剂消耗和废水处理费用,实现了铅锌多金属矿产资源的高效回收和节能环保。