Effects of different metal corrosion inhibitors on hydrogen suppression and film formation with Mg–Zn alloy dust in NaCl solutions

To improve the safety of wet dust removal systems for processing magnesium-based alloys, a new method is proposed for preventing hydrogen generation. In this paper, hydrogen generation by Mg–Zn alloy dust was inhibited with six common metal corrosion inhibitors. The results showed that sodium dodecylbenzene sulfonate was the best hydrogen inhibitor, while CeCl₃ enhanced hydrogen precipitation. The film-forming stability of sodium dodecylbenzene sulfonate was tested with different contents, temperatures, Cl^? concentrations and perturbation rates. The results showed that this inhibitor formed stable protective films on the surfaces of Mg–Zn alloy particles, and adsorption followed the Langmuir adsorption model.     

Effect of impact angle on wear behavior of Mo2NiB2–Ni cermets with different Ni content

Herein, the influence of the impact angle and Ni content on the wear behavior of Mo₂NiB₂–Ni cermets was studied using an erodent-carrying slurry comprising artificial seawater and SiO₂ sands. The results reveal that the material loss may be attributed to the wear damage caused by SiO₂ sands because cermets are expected to exhibit good corrosion resistance in artificial seawater. The relative density of cermets markedly influences their resistance to wear damage, and the material loss experienced by cermets with poor relative density is 2–4 times higher than that of cermets with good relative density; this occurs because a higher relative density can markedly enhance the mechanical properties and reduce the defects in the cermets. Moreover, the results indicate that as the impact angle increases from 0° to 60°, the manifestation of the wear mechanism changes from damaging the Ni binder phase (caused by single cutting wear) to damaging both the Mo₂NiB₂ ceramic and Ni binder phases due to the combination of cutting wear and impact wear. The wear damage is dominated by the cutting wear and impact wear from SiO₂ sand at the low and high impact angles, respectively. Furthermore, the severe deterioration of the single ceramic skeleton at high impact angles indicates that the synergistic influence of the Mo₂NiB₂ ceramic and Ni binder phases on enhancing the wear resistance of the cermets intensifies at high impact angles.     

大豆预处理车间除尘风网及防燃、防爆措施

大豆预处理车间的粉尘分为干式粉尘和湿式粉尘。粉尘易引起设备故障和车间污染,在限定空间和条件下会发生粉尘阴燃、起火甚至爆炸，给安全生产带来隐患。针对这些问题，根据大豆预处理工艺和设备的特点设计除尘风网和工艺风网。对大豆预处理车间的除尘风网和工艺风网进行了介绍。为减少含尘气体排放，除尘风网采取循环风设计，对可能出现阴燃、起火的溜管、弯头、设备的下料接管积尘处，以及可能出现粉尘爆炸的筒仓进行防燃、防爆和抑爆处理。通过对4 000 t/d 大豆压榨厂含尘气体排放实测表明，预处理车间的风网运行稳定，实现了安全和清洁生产。     

综采工作面活性磁化水防尘技术研究

煤矿生产是环境较为封闭的井下作业，具有一定的特殊性，作业空间湿度高、生产环境复杂，其中粉尘是危害最大的因素之一，会对机器和人体造成不同程度的损害。粉尘的危害主要由两方面决定:煤尘能够燃烧，在浓度较高时还会爆炸；粉尘会危害人的身体健康。以平煤股份十矿-320 m水平己四采区东翼下段的己_15-16-24130工作面为研究对象，研究磁化水除尘的方法及原理，通过对比分析优选出活性磁化水添加剂，在该工作面试验后具有良好的除尘效果，大大增加了可见度、降低了空气中悬浮的煤尘。研究对该矿井其他工作面除尘工作具有指导意义。     

采煤工作面煤层注水工艺优化与应用

针对目前煤层注水存在的施工钻孔效率低、钻孔深度达不到要求、注水钻孔封孔不严、封孔器回收困难等问题，研究注水工艺的改进优化，对钻机、钻具及封孔器进行重新设计选型，形成了一整套的注水装备。该装备的应用提高了施工效率，为降低工作面粉尘危害、抑制工作面瓦斯涌出、防治煤炭自然发火等危害探索出了更加高效的途径和方法。现场应用表明，煤层注水有效地改善了工作面作业环境，为工作面实现高产高效奠定了基础。     

安家岭储煤场输煤暗道通风除尘技术应用研究

针对输煤暗道的生产工艺现状，提出了采用通风与密闭抽尘净化技术，结合转载落料点密闭干雾降尘等技术措施，实现了输煤暗道内粉尘的的综合治理，通过粉尘浓度在线监测系统进行智能化控制，实现对输煤暗道通风除尘系统的远程连续监测监控，输煤暗道转载点下风侧5 m作业人员通行的位置总粉尘浓度由380.8 mg/m3降至19.8 mg/m3，降尘效率达94.8%，呼吸性粉尘浓度从96.7 mg/m3降至8.4 mg/m3，降尘效率达91.3%，降尘效果较好，有效地解决了输煤暗道及其转载落料点的粉尘污染问题，为输煤暗道内的粉尘防治提供参考依据。     

四台矿均压硐室的优化与研究

四台矿属于近距离容易自燃煤层开采,综采工作面采用均压通风系统。在进风顺槽中布置的本巷均压硐室,风机吸风口距离均压风门近,吸风风流经过带式输送机,往往会造成均压风门漏风严重,均压硐室周围温度较高、煤尘较大。据此四台矿优化均压硐室布置方式,采用独立均压硐室代替先前的本巷均压硐室。对优化前后的数据进行研究分析,得出独立均压硐室的应用在减少风门漏风量,降低温度,抑制煤尘方面均有很大改善,实践证明了采用独立均压硐室的可行性及优点。     

缓冲套对停止器挡杆防撞性能影响的测试与分析

对停止器挡杆的碰撞力进行了计算,在此基础上,对缓冲套对停止器挡杆防撞性能的影响进行测试与有限元分析。通过测试与分析确认,带聚氨酯缓冲套的停止器挡杆,碰撞力小,碰撞时间短,强度满足要求,且挡杆中铜套的变形小。在不考虑其它因素的前提下,优先选用带聚氨酯缓冲套的停止器挡杆。     

Extensive evaluation and classification of low-cost dust sensors in laboratory using a newly developed test method

An extensive evaluation of low-cost dust sensors was performed using an exponentially decaying particle concentration. A total of 264 sensors including 27 sensors with light-emitting diodes (LEDs) and 237 sensors with laser lighting sources were tested. Those tested sensors were classified into 4 groups based on the deviation from the reference data obtained by a reference instrument. The response linearities of all the tested samples for PM₁, PM_2.5, and PM₁₀ were in excellent agreement with the reference instrument, except a few samples. For the measurements of PM₁ and PM_2.5, the lighting source, that is, LED or laser, did not show any significant difference in overall sensor performance. However, LED-based sensors did not perform well for PM₁₀ measurements. The 32, 24, and 16% of all the tested sensors for PM₁, PM_2.5, and PM₁₀ measurement, respectively, are in the category of Class 1 (reference instrument reading ± 20%) requirement. The performance of the low-cost dust sensors for PM₁₀ measurement was relatively less satisfactory.     

河津腾晖煤业智能化降尘技术实践

以河津腾晖煤业为研究对象,基于智能化工作面开采及安全生产的需要,设计了智能化降尘系统,对该系统智能化控制关键技术进行了分析,提出了降尘点优化布置方案。该智能化降尘系统能较好地适应智能化开采技术的要求,实现了与综采智能控制系统的联动控制,降尘效果理想,为智能化开采提供了安全保障。