NNI-1型C_5/C_6烷烃异构化催化剂长周期运行分析及建议

中国石化海南炼油化工有限公司0.2 Mt/a C5/C6烷烃异构化装置以连续重整装置的拔头油为原料,使用NNI-1催化剂,采用一次通过流程,不设脱异戊烷塔和稳定塔,经设在连续重整装置内的脱丁烷塔稳定处理后作为汽油调合组分。该装置于2006年9月开工投产,截至2015年3月已连续运行3个周期。长周期运行分析结果表明:前两个周期中NNI-1催化剂具有较高的异构化活性及选择性,C5异构化率为60%左右,C6异构化率为80%左右,C6选择性为15%左右,产品辛烷值基本达到技术指标要求(RON≥78);而在第三周期运行中,催化剂积炭增加等原因导致其异构化活性及选择性降低,异构化产品辛烷值提升能力呈现逐步衰减的趋势,提高反应苛刻度已不能弥补催化剂活性下降造成的产品辛烷值降低。为保证装置长周期运行,建议择机停工对催化剂进行再生,或是直接换用与装置原料性质匹配的异构化催化剂。     

Molecular structure and granule morphology of native and heat‐moisture‐treated pinhão starch

Pinhão seed is an unconventional source of starch and the pines grow up in native forests of southern Latin America. In this study, pinhão starch was adjusted at 15, 20 and 25% moisture content and heated to 100, 110 and 120 °C for 1 h. A decrease in λ max (starch/iodine complex) was observed as a result of increase in temperature and moisture content of HMT. The ratio of crystalline to amorphous phase in pinhão starch was determined via Fourier transform infra red by taking 1045/1022 band ratio. A decrease in crystallinity occurred as a result of HMT. Polarised light microscopy indicated a loss of birefringence of starch granules under 120 °C at 25% moisture content. Granule size distribution was further confirmed via scanning electron microscopy which showed the HMT effects. These results increased the understanding on molecular and structural properties of HMT pinhão starch and broadened its food and nonfood industrial applications.     

Combination of heat treatment and chitosan coating to improve postharvest quality of wolfberry (Lycium barbarum)

The synergistic application of hot water dip at 42 °C for 30 min and 1% chitosan coating on differentiation in postharvest quality traits, microstructure as well as microbiological evolution of wolfberry fruits was investigated. Fresh wolfberry fruits were stored at 2 ± 0.5 °C and 90% relative humidity (RH) for 28 days. Results indicated the combination of prestorage heat treatment and chitosan coating maintained higher levels of ascorbic acid, total phenolic contents and antioxidant capacity as well as lower decay, compared with untreated wolfberry fruits. The possible mechanism was that the heat treatment almost sealed open stomata to limit the sites of pathogen penetration into fruits independently, followed by the biofilm formed by chitosan which controlled secondary infections as well as slowed changes in fruit respiration and metabolic activity in wolfberries. The synergistically treated fruit also exhibited a higher acceptability obtained by sensory analysis after cold storage. In this sense, the integrated application of heat treatment and chitosan coating could be regarded as an effective strategy to extend storage life and maintain the postharvest quality of wolfberry fruits.     

Efficacy of alpha-cypermethrin and thiamethoxam against Trogoderma granarium Everts (Coleoptera: Dermestidae) and Tenebrio molitor L. (Coleoptera: Tenebrionidae) on concrete

Laboratory bioassays were conducted to evaluate alpha-cypermethrin and thiamethoxam for the control of adults, small larvae and large larvae of the khapra beetle Trogoderma granarium, and the yellow mealworm beetle Tenebrio molitor, on concrete. Factors such as dose (0.025 and 0.1 mg alpha-cypermethrin or thiamethoxam/cm²), exposure interval (1, 3 and 7 d), and formulation (alpha-cypermethrin SC and thiamethoxam WG) were evaluated. Apart from immediate assessment at end of exposure, an assessment of delayed mortality was performed with the survivors of the 7-d exposure by removing them from the treated substrate and keeping them on untreated surfaces for 7 more days. After the 7-d exposure, more T. granarium adults were dead on dishes treated with alpha-cypermethrin than with thiamethoxam. Small larvae were generally less susceptible than adults. After 7 d, small larval mortality reached 64.4% for alpha-cypermethrin, while for thiamethoxam it was <6%. Large T. granarium larvae were more tolerant than the small ones. Delayed mortality of T. granarium adults was generally high for both insecticides and doses, and ranged between 43.3 and 63.3% of those that were still alive immediately after the 7-d treatment. For both larval categories, delayed mortality was higher for larvae that had been previously exposed to alpha-cypermethrin, than with thiamethoxam. For T. molitor, after the 7-d exposure, significantly more adults were dead on dishes treated with alpha-cypermethrin than with thiamethoxam. For small larvae mortality was 38.9% at the lowest thiamethoxam dose, but in the other cases ranged between 88.9 and 95.6%. In the case of large larvae, the overall mortality was low in all tested combinations. Regarding delayed mortality of this species, it remained at low levels, for both adults and small larvae. Our results indicate that T. molitor was more susceptible than T. granarium in both insecticides tested, but alpha-cypermethrin was more effective than thiamethoxam.     

Seawater-softening process through formation of calcite ooids

Conventional water-softening processes usually involve the exchange of Na⁺ ions for Ca²⁺ and Mg²⁺ using commercial or synthesized ion exchangers. The differences in chemical compositions of the ooids can be attributed to the formation in different environments. In this paper, ooid grains form inside assembled semi-pilot softening unit through a continuous chemical process involving reaction between bicarbonate ions and added lime using natural seawater. Our sample of Mediterranean seawater has low Mg²⁺/Ca²⁺ ratio (1.98%) within the range chemically favorable for precipitation of low-Mg calcite ooids. Precipitation of calcite occurs around pure quartz sand grains which act as nucleation points (the bed required for sand vessel is 1.65 l). The shape of the sand grains controls the overall external morphology of the resulting ooids; they vary in size from 0.5 to 3.0 mm and have a high degree of polish due to surface abrasion caused by continuous agitation inside the softening system. Calcite ooid grains (1.53 kg) formed within the seawater-softening unit every 18 days have many of the ooid features formed in marine environments. Ooids grow to a significant size, at a rate of about 0.17 mm of one layer thickness per day inside the softening unit. The average weight percent of calcite precipitate is 35.48% after 18 days, at 10 °C, 60 l/min and pH 9.0. The pellets comprise mainly CaCO₃ and SiO₂ and some metal ions which may substitute for calcium ions in calcite are present only in trace amounts of the total composition.     

Producing fully-lamellar microstructure for wrought beta-gamma TiAl alloys without single α-phase field

Fine-grained fully-lamellar (FL) microstructure is desired for TiAl components to serve as compressor/turbine blades and turbocharger turbine wheels. This study deals with the process and phase transformation to produce FL microstructure for Mo stabilized beta-gamma TiAl alloys without single α-phase field. Unlike the α + γ two-phased TiAl or beta-gamma TiAl with single α-phase field, the wrought multi-phase TiAl–4/6Nb–2Mo–B/Y alloys exhibit special annealing process to obtain FL microstructure. Short-term annealing at temperatures slightly above β-transus is recommended to produce the desired FL microstructure. The related mechanism is to guarantee the sufficient diffusion homogenization of β stabilizers during single β-phase annealing, and further avoid α decomposition by α → γ + β when cooling through α + β + γ phase field. The colony boundary β phase contributes to fine-grained nearly FL microstructure, by retarding the coarsening of the α phase grains.     

Linear friction welding of Ti6Al4V: experiments and modelling

Linear friction welding of the Ti6Al4V alloy is studied. A new definition of the energy input rate is proposed, based on an integration over time of the in-plane force and velocity; a strong correlation with the upset rate is then found. The effective friction coefficient is estimated to be 0·5±0·1 for varying frequencies and amplitudes, with only a weak dependence on the processing conditions displayed. A model is proposed that accounts for both the conditioning and equilibrium stages of the process, which is shown to be in good agreement with the experimental data. The model is used to study the mechanism by which the flash is formed. A criterion is proposed by which the rippled nature of its morphology can be predicted.     

Thermal treatment of waste photovoltaic module for recovery and recycling: Experimental assessment of the presence of metals in the gas emissions and in the ashes

The rapid expansion of the photovoltaic (PV) module market in the last years will determine in the near future a remarkable growth of corresponding waste. Then, the hazardous materials contained in the modules, such as Cd, Pb and Cr, could be released in the environment if the waste panels will not be handled adequately. Recycling processes of silicon crystalline panels, finalized to separate PV cells from the glass, involve the removal of the EVA (Ethylene Vinyl Acetate) layer through different methods, as the thermal treatment. During this treatment, some hazardous components can be released due to thermal degradation process. In this paper the metals released in the gas emissions and in the ashes due to the thermal treatment of modules were evaluated. For this purpose, three samples of crystalline panels were heated in furnace up to 600 °C and the complete degradation of the EVA was obtained. A mass balance between the sample and its components, before and after treatment, was performed in order to assess the weight loss percentage. Finally, after thermal treatment a qualitative analysis on the separated PV cell surface was performed by SEM-EDS (Scanning Electron Microscope equipped with Energy Dispersive Spectrometer).     

轻质滤料滤池的试验与研究

轻质滤料滤池是以比水密度略小的滤料为滤床的滤池，通过以净水厂的原水和污水处理厂的二级处理出水为过滤试验对象，所取得的结果表明：下向流轻质滤料滤池对浊度和悬浮固体（SS）的去除率分别可以达到80％和45％，而滤床的水头损失不超过15cm。因此轻质滤料滤池可以以预过滤的形式配置在过滤处理的净水和污水的处理工艺中。     

Thaumasite––direct, woodfordite and other possible formation routes

Two main formation routes for thaumasite exist below 15 °C. One is the direct route from C–S–H reacting with appropriate carbonate, sulfate, Ca²⁺ ions and excess water. The other route is the woodfordite route from ettringite reacting with C–S–H, carbonate, Ca²⁺ ions and excess water, in which thaumasite arises through the intermediate formation of the solid solution woodfordite. The woodfordite route for thaumasite formation appears to be relatively quicker (although still slow) than the direct route, presumably because with the former the ettringite already has the octahedral [M(OH)₆] units that can facilitate the critical change from [Al(OH)₆]³⁻ to [Si(OH)₆]²⁻ groupings. Both routes are mutually dependent on each other. The presence of magnesium salts can modify the path to thaumasite formation. High pressure might be able to stabilise [Si(OH)₆]²⁻ groupings and allow thaumasite to become formed above 15 °C. This possibility is discussed.